Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock) > DISASSEMBLY

for Preparation Click here



1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY


F051367
  1. Fix the rear differential carrier assembly to the overattachment.



2. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F001237E20
  1. Using a dial indicator, measure the vertical and lateral runout of the rear drive pinion companion flange.
    Text in Illustration 
    *a
    Vertical Runout
    *b
    Lateral Runout

    Distance from center to runout measurement point:
    30 mm (1.18 in.)

    Maximum Runout:
    Item
    Specified Condition
    Vertical runout
    0.09 mm (0.00354 in.)
    Lateral runout
    0.09 mm (0.00354 in.)

    If the runouts are not within the specifications, replace the companion flange.



3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


F051355
  1. Using a dial indicator, check the runout of the differential ring gear.

    Maximum runout:
    0.05 mm (0.00197 in.)

    If the runout is greater than the maximum, replace the ring gear with a new one.



4. INSPECT DIFFERENTIAL RING GEAR BACKLASH


F051386
  1. Using a dial indicator, check the backlash of the differential ring gear.

    Standard backlash:
    0.13 to 0.18 mm (0.00512 to 0.00708 in.)

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.



5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C003092
  1. Using a torque wrench, measure the preload of the backlash between the differential drive pinion and differential ring gear.

    Standard preload (at starting):
    0.78 to 1.05 N*m (8.0 to 11 kgf*cm, 6.9 to 9.3 in.*lbf)



6. INSPECT TOTAL PRELOAD


C003092
  1. Using a torque wrench, measure the preload with the teeth of the differential drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Total preload (at starting):
    Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)

    If necessary, disassemble and inspect the differential.



7. REMOVE REAR DRIVE PINION NUT


F044346E02
  1. Using SST and a hammer, loosen the staked part of the rear drive pinion nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered end facing the shaft.
    2. Do not grind SST tip with a grinder, etc.



    SA02349E10
  1. Using SST to hold the rear drive pinion companion flange sub-assembly, remove the nut.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09330-00021  



8. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F052175E10
  1. Using SST, remove the rear drive pinion companion flange sub-assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)



9. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR


F040564E04
  1. Using SST and a press, remove the rear differential dust deflector.

    SST
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)
    09950-00020  



10. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


SA02348E09
  1. Using SST, remove the rear differential carrier oil seal from the rear differential carrier assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09308-10010  



11. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


C228009E01
  1. Using SST, remove the rear drive pinion front tapered roller bearing from the rear differential pinion.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09556-22010  



12. REMOVE DIFFERENTIAL CASE ASSEMBLY


C250225E01
  1. Place matchmarks on the differential bearing cap and the rear differential carrier.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 bolts and the differential bearing cap.



    F051358E01
  1. Using SST and a plastic hammer, remove the 2 side bearing plate washers.

    SST
    09504-22011  

    HINT:
    Measure the plate washer thickness and note it down.

  1. Remove the differential case assembly with the bearing outer races from the rear differential carrier.

    HINT:
    Tag the disassembled parts to show the locations for reassembly.



13. REMOVE DIFFERENTIAL DRIVE PINION


C030540
  1. Remove the differential drive pinion and the rear differential drive pinion bearing spacer from the rear differential carrier assembly.



14. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


R010668E02
  1. Using SST and a press, remove the rear drive pinion rear tapered roller bearing from the differential drive pinion.

    SST
    09950-00020  

    HINT:
    If either the drive pinion or ring gear are damaged, replace them as a set.



15. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER


16. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


C249347E01
  1. Using SST, remove the rear drive pinion front tapered roller bearing from the carrier.

    SST
    09308-00010  



17. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


C091047
  1. Using a brass bar and a hammer, remove the rear tapered roller bearing and the rear differential drive pinion plate washer from the carrier.



18. REMOVE DIFFERENTIAL RING GEAR


C249394E01
  1. Place matchmarks on the differential ring gear and the differential case assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the 12 bolts.



    C014054
  1. Using a plastic hammer, tap on the differential ring gear to separate it from the differential case assembly.



19. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT


F051361
  1. Install the rear differential case bearing to the differential case assembly.

  1. Install the differential case to the rear differential carrier.

  1. Using a dial indicator, measure the differential case runout.

    Maximum case runout:
    0.05 mm (0.00197 in.)

  1. Remove the differential case.



20. REMOVE REAR DIFFERENTIAL CASE BEARING


C228401E01
  1. Using SST, remove the 2 rear differential case bearings from the differential case.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00480)

    HINT:
    Fix the claws of SST into the notch in the differential case.



21. DISASSEMBLE DIFFERENTIAL CASE ASSEMBLY


F051388
  1. Using a pin punch and hammer, remove the straight pin.

  1. Remove the pinion shaft, 2 pinion gears, 2 pinion gear thrust washers, 2 side gears and the 2 side gear thrust washers from the differential case.