Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER OIL SEAL

DIFFERENTIAL CARRIER OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new rear differential drive pinion bearing spacer.



2. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
  1. Using a brass bar and a hammer, install a new oil storage ring.

  1. Using SST and a hammer, install the front bearing outer race.

  1. Install the front bearing.

    SST
    09316-60011   (09316-00011, 09316-00021)



3. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER (w/ Differential Lock)


4. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


F040719E02
  1. Using SST and a hammer, install a new oil seal.

    SST
    09554-30011  

    Oil seal drive in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

  1. Coat oil seal lip with MP grease.



5. INSTALL REAR DRIVE COMPANION FLANGE SUB-ASSEMBLY REAR


F040716E02
  1. Using SST, install the companion flange.

  1. Coat the threads of a new nut with hypoid gear oil LSD.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)



    C088916E02
  1. Using SST to hold the companion flange, tighten the nut.

    SST
    09330-00021  

    Torque:
    451 N*m{ 4,599 kgf*cm , 333 ft.*lbf }



6. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C089308
  1. Using a torque wrench, measure the preload of backlash between the drive pinion and ring rear.

    New bearing:
    1.27 to 1.86 N*m (13 to 19 kgf*cm, 11 to 16 in.*lbf)

    Reused bearing:
    0.76 to 1.07 N*m (7.7 to 11 kgf*cm, 6.7 to 9.5 in.*lbf)

    If necessary, disassemble and inspect the differential assembly.



7. INSTALL REAR DRIVE PINION NUT


C089310
  1. Using a chisel and a hammer, stake the nut.



8. INSTALL PROPELLER SHAFT ASSEMBLY (for 2WD Regular Cab)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft assembly into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



9. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 2WD Except Regular Cab)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with the 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.



    F052184E02
  1. Adjust the center support bearing.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing to keep the intervals, as shown.
    2. In the same condition, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.039 to 0.039 in.) of each other in the vehicle's longitudinal direction when the vehicle is unladen.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



10. INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD Regular Cab)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C060588E01
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



11. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (4WD Except Regular Cab)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098708E02
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



12. ADD DIFFERENTIAL OIL


D025304E37
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the differential carrier assembly with differential gear oil.

    Oil type and viscosity:
    Toyota Genuine Differential gear oil LT APL 75W-85 GL-5 or equivalent.

    Capacity:
    Front differential carrier assembly:
    1.45 to 1.55 liters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)
    Rear differential carrier assembly (for 2WD):
    3.26 to 3.36 liters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Rear differential carrier assembly (for Pre, 4WD):
    2.75 to 2.85 liters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



13. INSPECT DIFFERENTIAL OIL


D025304E37
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the differential carrier assembly with differential gear oil.

    Oil type and viscosity:
    Toyota Genuine Differential gear oil LT APL 75W-85 GL-5 or equivalent.

    Capacity:
    Front differential carrier assembly:
    1.45 to 1.55 liters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)
    Rear differential carrier assembly (for 2WD):
    3.26 to 3.36 liters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Rear differential carrier assembly (for Pre, 4WD):
    2.75 to 2.85 liters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



14. INSPECT FOR DIFFERENTIAL OIL LEAKAGE