Home › SUSPENSION & AXLE › SUSPENSION › FRONT WHEEL ALIGNMENT (for 2WD)

FRONT WHEEL ALIGNMENT (for 2WD) > ADJUSTMENT

for Preparation Click here



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Standard Cold Tire Inflation Pressure:

    Tire Size
    Front Wheel
    kPa (kgf/cm2, psi)
    Rear Wheel
    kPa (kgf/cm2, psi)
    Spare Wheel
    kPa (kgf/cm2, psi)
    P215/70R15 97S
    210 (2.1, 30)
    230 (2.3, 33)
    230 (2.3, 33)
    P245/75R16 109S
    210 (2.1, 30)
    210 (2.1, 30)
    210 (2.1, 30)
    P265/70R16 111T
    200 (2.0, 29)
    220 (2.2, 32)
    220 (2.2, 32)
    P265/65R17 110S
    200 (2.0, 29)
    200 (2.0, 29)
    200 (2.0, 29)
    P255/45R18 99V
    240 (2.4, 35)
    240 (2.4, 35)
    240 (2.4, 35)
    P265/60R18 109H
    200 (2.0, 29)
    200 (2.0, 29)
    200 (2.0, 29)



    C164558
  1. Using a dial indicator, check the tire runout.

    Standard Tire Runout:
    Vertical
    3.0 mm (0.118 in.) or less
    Lateral
    3.0 mm (0.118 in.) or less



2. MEASURE VEHICLE HEIGHT

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.



  1. Measure the vehicle height.


    F051670E02


    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side

    Measuring points:
    A:
    Ground clearance of front wheel center
    B:
    Ground clearance of adjustment cam bolt center (front side)
    C:
    Ground clearance of rear wheel center
    D:
    Ground clearance of rear leaf spring front side bush center


    Vehicle Height (Unloaded Vehicle):

    Vehicle Model
    Tire Size
    A - B
    C - D
    TRN220L-TRMDKA
    P215/70R15
    89 mm (3.50 in.)
    49 mm (1.93 in.)
    TRN220L-TRPDKA
    P215/70R15
    91 mm (3.58 in.)
    50 mm (1.97 in.)
    TRN225L-CRMDKA
    P215/70R15
    85 mm (3.35 in.)
    54 mm (2.13 in.)
    TRN225L-CRPDKA
    P215/70R15
    87 mm (3.43 in.)
    54 mm (2.13 in.)
    TRN225L-PRPDKA
    P215/70R15
    89 mm (3.50 in.)
    59 mm (2.32 in.)
    GRN225L-CRFDKA
    P255/45R18
    117 mm (4.61 in.)
    86 mm (3.39 in.)

    NOTICE:
    The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


Z003382E25
  1. Install the camber-caster-kingpin gauge and position the front wheel on the wheel alignment tester.
    Text in Illustration 
    *1
    Wheel Alignment Tester
    *2
    Gauge

  1. Inspect the camber, caster and steering axis inclination.

    Camber, Caster and Steering Axis Inclination (Unloaded Vehicle):

    Vehicle Model
    Tire Size
    Camber
    Caster
    Steering Axis Inclination
    TRN220L-TRMDKA
    P215/70R15
    0°10' +/- 45'
    (0.17° +/- 0.75°)
    3°58' +/- 45'
    (3.96° +/- 0.75°)
    10°45' +/- 45'
    (10.75° +/- 0.75°)
    TRN220L-TRPDKA
    P215/70R15
    0°08' +/- 45'
    (0.13° +/- 0.75°)
    3°57' +/- 45'
    (3.95° +/- 0.75°)
    10°48' +/- 45'
    (10.80° +/- 0.75°)
    TRN225L-CRMDKA
    P215/70R15
    0°14' +/- 45'
    (0.24° +/- 0.75°)
    4°09' +/- 45'
    (4.15° +/- 0.75°)
    10°41' +/- 45'
    (10.69° +/- 0.75°)
    TRN225L-CRPDKA
    P215/70R15
    0°12' +/- 45'
    (0.20° +/- 0.75°)
    4°11' +/- 45'
    (4.18° +/- 0.75°)
    10°44' +/- 45'
    (10.73° +/- 0.75°)
    TRN225L-PRPDKA
    P215/70R15
    0°09' +/- 45'
    (0.15° +/- 0.75°)
    4°19' +/- 45'
    (4.31° +/- 0.75°)
    10°46' +/- 45'
    (10.77° +/- 0.75°)
    GRN225L-CRFDKA
    P255/45R18
    -0°37' +/- 45'
    (-0.62° +/- 0.75°)
    5°09' +/- 45'
    (5.15° +/- 0.75°)
    11°32' +/- 45'
    (11.53° +/- 0.75°)

    NOTICE:
    1. Perform the inspection while the vehicle is empty (without spare tires or tools on board).
    2. The tolerance for the difference between the left and right wheels is 0°30' (0.50°) or less for both the camber and caster.

    If the steering axis inclination is not as specified after the camber and caster have been correctly adjusted, recheck the steering knuckle and front wheel for distortion and slack.



4. ADJUST CAMBER AND CASTER

NOTICE:
Inspect the toe-in after the camber has been adjusted.

  1. Loosen the 2 nuts.



  1. Turn the camber adjust cam and adjust the camber and caster.

    HINT:
    Try to adjust the camber and caster to the central values.



    F051672E02


    Text in Illustration 
    *1
    Front Cam (LH)
    *2
    Front Cam (RH)
    *3
    Rear Cam (LH)
    *4
    Rear Cam (RH)
    *a
    Front of the Vehicle
    -
    -



    F051673E01
  1. How to read the adjustment chart (using examples).

    1. Measure the present alignment.

      Camber:
      -0°17' (0.28°)

      Caster:
      3°30' (3.50°)

    2. Calculate the difference between the standard value (A) and the measured value (B) on the adjustment chart.

      Standard value:
      Camber:
      0°13' (0.22°)
      Caster:
      3°50' (3.84°)
      Formula:
      B - A = C
      Camber:
      -0°17' - 0°13' = -0°30'
      Caster:
      3°30' - 3°50' = -0°20'



    3. As shown in the chart, read the distance from the marked point to the 0 point, and adjust the front and/or rear adjusting cams accordingly.

      Front adjust cam:
      - (Shorter) 1.9

      Rear adjust cam:
      - (Shorter) 0.8



      C163774E01



5. INSPECT TOE-IN


SA03213E21
Text in Illustration 
*a
Front of the Vehicle

Toe-in (Unloaded Vehicle):

Vehicle Model
Tire Size
A + B
C - D
TRN220L-TRMDKA
P215/70R15
0°04' +/- 0°06' (0.065° +/- 0.108°)
0.77 +/- 2 mm (0.030 +/- 0.08 in.)
TRN220L-TRPDKA
P215/70R15
0°03' +/- 0°06' (0.049° +/- 0.108°)
0.58 +/- 2 mm (0.023 +/- 0.08 in.)
TRN225L-CRMDKA
P215/70R15
0°05' +/- 0°06' (0.089° +/- 0.108°)
1.06 +/- 2 mm (0.042 +/- 0.08 in.)
TRN225L-CRPDKA
P215/70R15
0°04' +/- 0°06' (0.073° +/- 0.108°)
0.86 +/- 2 mm (0.034 +/- 0.08 in.)
TRN225L-PRPDKA
P215/70R15
0°03' +/- 0°06' (0.057° +/- 0.108°)
0.67 +/- 2 mm (0.026 +/- 0.08 in.)
GRN225L-CRFDKA
P255/45R18
0°02' +/- 0°06' (0.038° +/- 0.108°)
0.45 +/- 2 mm (0.018 +/- 0.08 in.)

If the toe-in is not within the specified range, adjust it at the rack ends.


6. ADJUST TOE-IN
  1. Remove the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Turn the right and left rack ends uniformly to adjust the toe-in.

    HINT:
    Try to adjust the toe-in to the middle of the specified range.



    F051671
  1. Make sure that the lengths of the right and left rack ends are the same.

  1. Tighten the tie rod end lock nuts.

    Torque:
    56 N*m{ 566 kgf*cm , 41 ft.*lbf }

  1. Install the boots onto the seats with the clips.

    HINT:
    Make sure that the boots are not twisted.



7. INSPECT WHEEL TURNING ANGLE


SA00028E18
  1. Turn the steering wheel fully, and measure the turning angle.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    *c
    Front of the Vehicle

    Wheel Turning Angle (Unloaded Vehicle):
    Inside Wheel
    Outside Wheel (Reference)
    38°48' (36°48' to 39°48')
    38.80° (36.80° to 39.80°)
    32°30' (30°30' to 33°30')
    32.50° (30.50° to 33.50°)

    If the right and left turning angles of the inside and outside wheels are not within the specified ranges, check the right and left rack end lengths.