Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY


D029376E01


  1. Inspect the one-way clutch.

    1. Install SST into the inner race of the one-way clutch.

      SST
      09350-32014   (09351-32010)

    2. Set SST so that it fits in the notch of the converter hub and outer race of the one-way clutch.

      SST
      09350-32014   (09351-32020)



    3. D029377E02
    4. With the torque converter standing on its side, check that the clutch locks when turned counterclockwise and rotates freely and smoothly clockwise.
      If necessary, clean the converter and check the one-way clutch again.
      Replace the converter if the one-way clutch still doesn't operate as specified.



    D025367E08
  1. Check the condition of the torque converter clutch assembly.

    1. If the inspection result of the torque converter clutch assembly matches any of the cases mentioned below, replace the torque converter clutch.

      Malfunction item:
      Any metallic sound is heard from the torque converter clutch during stall test or when the shift lever is in the neutral position.
      One-way clutch is free or locked in both directions. Fine powders exceeding the sample limit are identified in ATF. (See the sample.)

      HINT:
      The sample shows the auto fluid of approximately 0.25 liters (0.26 US qts, 0.22 Imp. qts) that is taken out from the removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter clutch and drain it with the installation surface facing up.



    C011090
  1. Clean and then check the oil cooler and oil pipe line.

    1. If inspecting the torque converter clutch or exchanging the ATF, clean the oil cooler and oil pipe line.

      HINT:
      1. Apply compressed air of 196 kPa (2 kgf/cm2, 28 psi) from the inlet hose.
      2. If plenty of fine powders are identified in the ATF, add new ATF using a bucket pump and clean the ATF again.

    2. If the ATF is cloudy, inspect the oil cooler (radiator).



    D025368E06
  1. Be careful not to deform the torque converter clutch or damage the oil pump gear.

    1. When any marks due to interference are found on the end of the bolt on the torque converter clutch and on the bottom of the bolt hole, replace the bolt and the torque the converter clutch.

    2. All the bolts should be the same length.

    3. Do not lose any spring washers.



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Install the torque converter clutch onto the automatic transmission.



    D025544E05
  1. Using calipers and a straight edge, measure dimension A, between the transmission and the end surface of the drive plate, as shown in the illustration.

    Standard:
    A: 22.28 mm (0.8772 in.)



    D025545E05
  1. Using calipers and a straight edge, measure the dimension B shown in the illustration and check that B is greater than A measured in (b).

    Standard:
    23.28 mm (0.9165 in.) or more



3. INSTALL REAR NO.1 ENGINE MOUNTING INSULATOR
  1. Install the engine mounting insulator with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



4. INSTALL NO.1 TRANSMISSION CONTROL CABLE BRACKET
  1. Install the transmission control cable bracket No. 1 with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


F050826E01
  1. Install the automatic transmission with the 7 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf } for bolt A
    37 N*m{ 377 kgf*cm , 27 ft.*lbf } for bolt B

  1. Install the 6 torque converter clutch mounting bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    HINT:
    First install the black bolt and then the other 5 bolts.

  1. Install the flywheel housing under cover.



6. INSTALL WIRE HARNESS


7. INSTALL STARTER ASSEMBLY


G037950E01
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    G037949E01
  1. Connect the starter connector.

  1. Install the starter wire harness with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.



8. INSTALL NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Install the frame crossmember sub-assembly No. 3 with the 4 bolts and 4 nuts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the frame crossmember sub-assembly No. 3 with the 4 bolts.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }

  1. Connect the heated oxygen sensor connector.



9. INSTALL FRONT SUSPENSION MEMBER BRACKET RH
  1. Install the 2 front suspension member brackets with the 8 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



10. INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY


F050829
  1. ROD TYPE:

    1. Install the floor shift gear shifting rod, then install the clip.



11. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. CABLE TYPE:

    1. Connect the transmission control cable with the clip.

    2. Connect the transmission control cable with the nut.

      Torque:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }



12. INSTALL MANIFOLD STAY


F050821E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf } for bolt A
    44 N*m{ 449 kgf*cm , 33 ft.*lbf } for bolt B
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for bolt C



13. INSTALL NO.1 OIL COOLER INLET TUBE
  1. Provisionally install the oil cooler inlet tube No. 1.

  1. Provisionally install the oil cooler outlet tube No. 1.



    F050803E01
  1. Install the 3 clamps and 3 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for bolt A
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf } for bolt B

  1. Using a union nut wrench, tighten the oil cooler inlet tube No. 1.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



14. INSTALL NO.1 OIL COOLER OUTLET TUBE
  1. Using a union nut wrench, tighten the oil cooler outlet tube No. 1.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



15. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
  1. Coat new O-ring with Toyota Genuine ATF Type T-IV or equivalent and install it onto the oil filler tube.

  1. Install the oil filler tube with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



16. INSTALL TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY


17. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Except Regular Cab)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with the 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.



    F052184E02
  1. Adjust the center support bearing.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing to keep the intervals, as shown.
    2. In the same condition, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.039 to 0.039 in.) of each other in the vehicle's longitudinal direction when the vehicle is unladen.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



18. INSTALL PROPELLER SHAFT ASSEMBLY (for Regular Cab)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft assembly into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



19. ADJUST SHIFT LEVER POSITION


D028682E02
  1. Push the control shaft fully rearward.

  1. Turn the control shaft lever 2 notches counterclockwise to the N position.

  1. Set the shift lever to the N position.



20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



21. ADD AUTOMATIC TRANSMISSION FLUID


22. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
Drive the vehicle until the engine and transmission are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)



    F051843E01
  1. Park the vehicle on a level surface and engage the parking brake.

  1. With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L, and then return it to the P position.

  1. Pull out the oil level gage and wipe it clean.

  1. Push it back fully into the pipe.

  1. Pull it out and check that the fluid level is within the HOT range.
    If there is any leakage, repair or replace O-rings, seal packings, oil seals, plugs or other parts.



23. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK


24. INSPECT SHIFT LEVER POSITION
  1. Check that the shift lever moves smoothly and appropriately from the P to R position, only when the ignition switch is turned to ON and the brake pedal is depressed.

  1. When starting the engine, make sure that the vehicle moves forward when shifting the lever from the N to D position and moves rearward when shifting the lever to the R position.