Home › TRANSMISSION ยท A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ASSEMBLY


F050671
  1. Install the transfer assembly with the 8 bolts.

    Torque:
    24 N*m{ 244 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Take care not to damage the adaptor rear oil seal with the transfer input gear spline.



2. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY


D029376E01


  1. Inspect the one-way clutch.

    1. Install SST into the inner race of the one-way clutch.

      SST
      09350-32014   (09351-32010)

    2. Set SST so that it fits in the notch of the converter hub and outer race of the one-way clutch.

      SST
      09350-32014   (09351-32020)



    3. D029377E04
    4. With the torque converter standing on its side, check that the clutch locks when turned counterclockwise and rotates freely and smoothly clockwise.
      If necessary, clean the converter and check the one-way clutch again.
      Replace the converter if the one-way clutch still does not operate as specified.
      Text in Illustration 
      V100135
      Lock
      V100136
      Free



    C197457E04
  1. Check the condition of the torque converter clutch assembly.
    Text in Illustration 
    *a
    Sample showing maximum allowable amount of powder in ATF

    1. If the inspection result of the torque converter clutch assembly matches any of the cases mentioned below, replace the torque converter clutch.

      Malfunction item:
      Any metallic sound is heard from the torque converter clutch during stall test or when the shift lever is in N.
      One-way clutch is free or locked in both directions. Fine powder exceeding the sample limit are identified in ATF. (See the sample.)

      HINT:
      The sample shows the auto fluid of approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) that is taken out from the removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter clutch and drain it with the installation surface facing up.



    C011090
  1. Clean and then check the oil cooler and oil pipe line.

    1. If inspecting the torque converter clutch or exchanging the ATF, clean the oil cooler and oil pipe line.

      HINT:
      1. Apply compressed air of 196 kPa (2 kgf/cm2, 28 psi) from the inlet hose.
      2. If excessive fine powder is found in the ATF, add new ATF using a bucket pump and clean the ATF again.

    2. If the ATF is cloudy, inspect the oil cooler (radiator).



    D025368E29
  1. Be careful not to deform the torque converter clutch or damage the oil pump gear.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect
    *c
    Bottom is damaged

    1. When any marks due to interference are found on the end of the bolt on the torque converter clutch and on the bottom of the bolt hole, replace the bolt and the torque converter clutch.

    2. All the bolts should be the same length.

    3. Do not lose any spring washers.



3. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
  1. Install the engine mounting insulator with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



4. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
  1. Install the No. 1 transmission control cable bracket with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



5. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


    C229014
  1. Engage the splines of the input shaft and turbine runner.



    C229015
  1. Engage the splines of stator shaft and the stator while turning the torque converter clutch assembly.

    HINT:
    If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm (0.394 in.) and engage the splines while rotating the torque converter clutch.



    C229016
  1. Turn the torque converter clutch assembly to engage the key of oil pump drive gear into the slot on the torque converter clutch assembly.

  1. Clean the torque converter clutch set bolt holes.



    C191485E04
  1. Using a vernier caliper and a straightedge, measure dimension "A" between the automatic transmission fitting surface of the engine and the torque converter fitting surface of the drive plate.
    Text in Illustration 
    *a
    Automatic Transmission Fitting Surface
    *b
    Torque Converter Fitting Surface



    D025545E05
  1. Using a vernier caliper and a straightedge, measure the dimension B shown in the illustration and check that dimension B is greater than dimension A, which was measured in step (e).

    Standard:
    B: 31.75 mm (1.250 in.) or more

    NOTICE:
    1. Make sure to deduct the thickness of the straightedge.
    2. If the automatic transmission is installed to the engine with the torque converter clutch not sufficiently inserted, the torque converter clutch may be damaged.



6. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


    C228892E01
  1. Confirm that the 2 knock pins are on the automatic transmission contact surface of the engine cylinder block before automatic transmission installation.
    Text in Illustration 
    *1
    Knock Pin

  1. Apply clutch spline grease to the round of the crankshaft contact surface with the torque converter centerpiece.
    Text in Illustration 
    *2
    Crankshaft
    *a
    Crankshaft Contact surface

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent

    Maximum spread:
    Approximately 1 g (0.0353 oz)



    C226899E01
  1. Install the automatic transmission with the 8 bolts. Install bolt A together with the transfer breather bracket.

    Torque:
    Bolt A, B:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    Bolt C:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    P000601E07
  1. Clean and degrease the 6 torque converter setting bolts.

  1. Apply a few drops of adhesive to 2 or 3 threads of the tips of the 6 torque converter setting bolts.
    Text in Illustration 
    *1
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, three Bond 1324 or equivalent.



    G038107E01
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Install the 6 torque converter setting bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    First install the black colored bolt, and then the remaining 5 silver colored bolts.

  1. Install the flywheel housing under cover.



7. CONNECT TRANSFER BREATHER HOSE
  1. Connect the transfer breather hoses to the breather bracket.



8. INSTALL STARTER ASSEMBLY


G037950E01
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    G037949E01
  1. Connect the starter connector.

  1. Install the starter wire harness with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.



9. CONNECT WIRE HARNESS AND CONNECTORS
  1. Connect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connector.

  1. Attach the connector clamp and 8 harness clamps.

    NOTICE:
    Clamp the transmission wire and transfer breather hose clamps to the sections of the transfer breather hoses marked with red paint.

  1. Tilt up the transmission.



10. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



11. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Connect the transmission control cable assembly to the transmission control cable bracket with a new clip, and connect the cable end to the control shaft lever with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



12. INSTALL MANIFOLD STAY


F050821E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    Bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    Bolt B:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }
    Bolt C:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



13. CONNECT NO. 1 OIL COOLER INLET TUBE
  1. Provisionally install the No. 1 oil cooler inlet tube.

  1. Provisionally install the No. 1 oil cooler outlet tube.



    C227724E01
  1. Install the 3 clamps and 3 bolts.

    Torque:
    Bolt A:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }
    Bolt B:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    C226905
  1. Using a union nut wrench, tighten No. 1 the oil cooler inlet tube.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

    HINT:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



14. CONNECT NO. 1 OIL COOLER OUTLET TUBE
  1. Using a union nut wrench, tighten the No. 1 oil cooler outlet tube.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



15. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV or equivalent and install it onto the oil filler tube.

  1. Install the oil filler tube with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



16. INSTALL TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY


17. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


C098708E03
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



18. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Access Cab)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098708E02
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



19. INSTALL PROPELLER SHAFT ASSEMBLY (for Regular Cab)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C060588E01
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



20. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A077857E01
  1. Check the free length.

    1. Using vernier calipers, measure the free length of the compression spring.

      Minimum:
      40.5 mm (1.594 in.)

      If the free length is less than the minimum, replace the compression spring.



    A076194E06
  1. Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the exhaust manifold.

    NOTICE:
    1. Make sure that the gasket is in the correct angle when installing.
    2. Do not reuse the removed gasket.
    3. Never push a new gasket into the exhaust manifold by installing the exhaust pipe front into the exhaust manifold.

  1. Install the exhaust pipe front into the exhaust pipe support.

  1. Tighten the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



21. CONNECT WIRE HARNESS AND CONNECTOR
  1. Connect the heated oxygen sensor connector and the oxygen sensor harness clamp.

  1. Connect the air fuel ratio sensor connector and the air fuel ratio sensor harness clamp.



22. ADJUST SHIFT LEVER POSITION


    F050822
  1. Remove the nut and clip, and disconnect the transmission control cable assembly from the automatic transmission.



    C213714E03
  1. Turn the control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.
    Text in Illustration 
    *a
    N Position
    *b
    P Position
    *c
    R Position

  1. Connect the transmission control cable assembly to the transmission control cable bracket with a new clip, and connect the cable end to the control shaft lever with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



23. INSTALL FRONT FENDER SEAL LH
  1. Install the front fender seal LH with the 5 clips.



24. INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (for Regular Cab)
  1. Install the engine under cover No. 2 with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



25. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the engine under cover No. 1 with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



27. ADD AUTOMATIC TRANSMISSION FLUID


28. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
  1. Drive the vehicle so that the engine and transmission are at the normal operating temperature.

    Standard ATF temperature:
    70 to 80°C (158 to 176°F)

  2. The ATF temperature can be checked with the Techstream.
    Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 3.

  1. Park the vehicle on a level surface and set the parking brake.

  1. With the engine idling and the brake pedal depressed, move the shift lever into all positions from P to L. Then return it to P.

  1. Pull out the dipstick and wipe it clean.

  1. Push it back fully into the pipe.



    G036408E02
  1. Pull it out and check that the fluid level is in the HOT range.
    Text in Illustration 
    *a
    OK
    *b
    Add
    If the level is not in the HOT range, add transmission fluid.



29. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK


30. INSPECT SHIFT LEVER POSITION
  1. Check that the shift lever moves smoothly and appropriately from P to R, only when the ignition switch is turned to ON and the brake pedal is depressed.

  1. When starting the engine, make sure that the vehicle moves forward when shifting the lever from N to D and moves rearward when shifting the lever to R.