Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE PROPELLER SHAFT ASSEMBLY (for Regular Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    D033911E01
  1. Remove the propeller shaft.

  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



3. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Except Regular Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts and 4 washers, and remove the propeller shaft.



    D033912
  1. Remove the 2 center support bearing bolts from the frame crossmember.



    D033911E01
  1. Pull out the propeller shaft.

  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



4. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug, gasket and drain ATF.

  1. Install a new gasket and drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



5. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY


6. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


F050819
  1. Remove the 2 bolts and oil filler tube.



7. REMOVE NO.1 OIL COOLER OUTLET TUBE


F050803
  1. Remove the 3 bolts and 3 clamps.



    F050820E02
  1. Using a union nut wrench, disconnect the oil cooler outlet tube No. 1.



8. REMOVE NO.1 OIL COOLER INLET TUBE
  1. Using a union nut wrench, disconnect the oil cooler inlet tube No. 1.



9. REMOVE MANIFOLD STAY


F050821
  1. Remove the 3 bolts and manifold stay.



10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


F050822
  1. CABLE TYPE:

    1. Remove the nut and disconnect the transmission control cable.

    2. Remove the clip and disconnect the transmission control cable.



11. SEPARATE FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY


F050829
  1. ROD TYPE:

    1. Remove the clip and separate the floor shift gear shifting rod from the automatic transmission.



12. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


Z035558
  1. Support the automatic transmission assembly with a transmission jack.



13. REMOVE FRONT SUSPENSION MEMBER BRACKET RH


F050831
  1. Remove the 8 bolts and 2 front suspension member brackets.



14. REMOVE NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


F050823
  1. Disconnect the heated oxygen sensor connector.



    F050824
  1. Remove the 4 bolts from the frame crossmember sub-assembly No. 3.

  1. Remove the 4 nuts, 4 bolts and frame crossmember sub-assembly No. 3.



15. REMOVE STARTER ASSEMBLY


G037949E01
  1. Remove the terminal cap.

  1. Remove the nut, then remove the starter wire harness.

  1. Disconnect the starter connector.



    G037950E01
  1. Remove the 2 bolts, then remove the starter.



16. DISCONNECT CONNECTOR


Q006925
  1. Tilt down the transmission.

    NOTICE:
    Take care so that the cooling fan does not come in contact with the fan shroud.

  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the transmission wire connector.

  1. Disconnect the 2 speed sensor connectors.

  1. Disconnect the temperature sensor connector.



17. DISCONNECT WIRE HARNESS


18. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


F050825
  1. Remove flywheel housing dust seal.

  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley bolt with a wrench and remove the 6 bolts.



    F050826
  1. Remove the 7 bolts.

  1. Separate and remove the automatic transmission.



19. REMOVE NO.1 TRANSMISSION CONTROL CABLE BRACKET


F050827
  1. Remove the 2 bolts and transmission control cable bracket No. 1.



20. REMOVE REAR NO.1 ENGINE MOUNTING INSULATOR


F050828
  1. Remove the 4 bolts and engine mounting insulator rear No. 1.



21. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY