Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › VALVE BODY ASSEMBLY

VALVE BODY ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


F051845E01
  1. Install the shift solenoid valve SLU with the bolt.

    Torque:
    6.4 N*m{ 65 kgf*cm , 56 in.*lbf }

  1. Install the shift solenoid valves S1 and S2 with the bolt.

    Torque:
    6.4 N*m{ 65 kgf*cm , 56 in.*lbf }

  1. Install the shift solenoid valve SLT with the bolt.

    Torque:
    6.4 N*m{ 65 kgf*cm , 56 in.*lbf }



    AT08393E01
  1. Align the groove of the manual valve with the pin of the lever.



    D029011E02
  1. Install the 20 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A: 23 mm (0.91 in.)
    Bolt B: 28 mm (1.10 in.)
    Bolt C: 36 mm (1.42 in.)



2. INSTALL TRANSMISSION WIRE


Q000625
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV or equivalent, and install it onto the solenoid wiring.

  1. Install the solenoid wiring onto the case, and install the stopper plate.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    D029778E03
  1. Connect the connectors to each shift solenoid valve.



3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


D005554
  1. Install 5 new gaskets.



    D005550E02
  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 100 kgf*cm , 7 ft.*lbf }

    Bolt length:
    Bolt A: 14 mm (0.55 in.)
    Bolt B: 20 mm (0.79 in.)
    Bolt C: 23 mm (0.91 in.)



4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


D029014

HINT:
Remove any packing material and be careful not to drop oil on the contact surfaces of the transmission case and oil pan sub-assembly.

  1. Install the 3 magnets onto the oil pan sub-assembly, in the portions indicated in the illustration.



    D028715
  1. Apply seal packing to the oil pan, as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent Seal
    Seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

  1. Install the oil pan sub-assembly with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



5. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
  1. Coat new O-ring with Toyota Genuine ATF Type T-IV or equivalent and install it onto the oil filler tube.

  1. Install the oil filler tube with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



6. ADD AUTOMATIC TRANSMISSION FLUID


7. INSPECT AUTOMATIC TRANSMISSION FLUID

HINT:
Drive the vehicle until the engine and transmission are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)



    F051843E01
  1. Park the vehicle on a level surface and engage the parking brake.

  1. With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L, and then return it to the P position.

  1. Pull out the oil level gage and wipe it clean.

  1. Push it back fully into the pipe.

  1. Pull it out and check that the fluid level is within the HOT range.
    If there is any leakage, repair or replace O-rings, seal packings, oil seals, plugs or other parts.



8. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK