Home › DRIVE LINE › PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY (for Access Cab 2WD and Double Cab 2WD)

PROPELLER SHAFT ASSEMBLY (for Access Cab 2WD and Double Cab 2WD) > DISASSEMBLY

for Preparation Click here



1. INSPECT PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING
  1. Check the spider bearings for wear and damage.

  1. Check each spider bearings axial play by turning the yoke while holding the shaft tightly.

    Maximum bearing axial play:
    0 to 0.05 mm (0 to 0.002 in.)

    If the bearing axial play is greater than the maximum, replace the spider bearing.



2. REMOVE PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING


D033920E01
  1. Place matchmarks on the propeller shaft and universal joint yoke.



    D033913
  1. Using a brass bar and hammer, slightly tap in the spider bearing.

  1. Using needle-nose pliers, remove the 4 snap rings from the grooves.



    D033914E01
  1. Clamp the propeller shaft in a vise between aluminum plates.

  1. Using SST, push the spider bearing out of the propeller shaft.

    SST
    09332-25010  

    HINT:
    Sufficiently raise the part indicated by (A) so that it does not come into contact with the spider bearing.



    D033915E01
  1. Clamp the removed spider bearing outer race in a vise and tap the propeller shaft to remove the spider bearing.

    NOTICE:
    Do not tap the shaft tube.

    HINT:
    Remove the spider bearing from the opposite side of the spider using the same procedure.

  1. Separate the propeller with center bearing shaft assembly from the propeller shaft assembly.



    D033916E01
  1. Reinstall the 2 removed spider bearings onto the spider and clamp the spider bearings in a vise.

  1. Using SST, push the bearing out of the yoke.

    SST
    09332-25010  

    HINT:
    Sufficiently raise the part indicated by (A) so that it does not come into contact with the bearing.



    D033917E01
  1. Clamp the outer bearing race in a vise and tap off the yoke with a hammer.

  1. Remove the spider.



3. REMOVE PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING


D033919E01
  1. Place matchmarks on the flange yoke and sleeve yoke.



    D033918
  1. Using a brass bar and hammer, slightly tap in the spider bearing.

  1. Using 2 needle-nose pliers, remove the 4 snap rings from the grooves.



    F015025E03
  1. Clamp the propeller shaft in a vise between the aluminum plates.

  1. Using SST, push the spider bearing out of the propeller shaft.

    SST
    09332-25010  

    HINT:
    Sufficiently raise the part indicated by (A) so that it does not come into contact with the bearing.



    F044192E01
  1. Clamp the removed spider bearing outer race in a vise and tap the propeller shaft to remove the spider bearing.

    NOTICE:
    Do not tap the shaft tube.

    HINT:
    Remove the spider bearing from the opposite side of the spider using the same procedure.

  1. Separate the flange yoke and spider from the propeller shaft.



    F015030E03
  1. Reinstall the 2 removed spider bearings onto the spider and clamp the spider bearings in a vise.

  1. Using SST, push the bearing out of the yoke.

    SST
    09332-25010  

    HINT:
    Sufficiently raise the part indicated by (A) so that it does not come into contact with the bearing.



    F044193E01
  1. Clamp the outer bearing race in a vise and tap off the yoke with a hammer.

  1. Remove the spider.



4. REMOVE CENTER SUPPORT BEARING ASSEMBLY NO. 2


D033921E01
  1. Fix the yoke at the center bearing section in a vice.

  1. Using a chisel and a hammer, loosen the staked part of the lock nut.

  1. Place matchmarks on the yoke and shaft.

  1. Using a brass bar and hammer, remove the center yoke, spacer and center support bearing from the intermediate shaft.