Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD

RADIO ANTENNA CORD > INSTALLATION

for Preparation Click here



1. INSTALL RADIO ANTENNA CORD SUB-ASSEMBLY



E075961E01

  1. Engage the 4 claws and install the Radio antenna cord.



2. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY


3. INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
  1. Install the instrument panel sub-assembly with passenger airbag assembly with the 8 bolts and nut.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. Engage the 5 clamps and connect the 4 connectors.

  1. Remove the protective tape from the steering column cover upper and steering wheel sub-assembly.



4. CONNECT PASSENGER AIRBAG CONNECTOR


    F050426E02
  1. Connect the passenger airbag connector and clamp.



5. INSTALL INSTRUMENT SIDE PANEL RH


    B085791E01
  1. Engage the 3 claws and install the instrument side RH.



6. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 5 clips and install the instrument lower cover.

  1. Install the bolt <B>.



7. INSTALL LOWER INSTRUMENT PANEL LH
  1. Install the lower instrument panel LH with the 3 bolts <B>.



8. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH
  1. Engage the 2 clips and install the instrument panel lower finish panel sub-assembly RH.

  1. Install the bolt <B>.



9. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B290404
  1. Pull the bottom of the stopper.



    B290405
  1. Attach the stopper to the glove compartment door as shown in the illustration.



    E232355
  1. Install the glove compartment door assembly with 3 hinges, holding it horizontal.



    E232356
  1. Slightly deform the upper part of the glove compartment door assembly, and install the glove compartment door assembly.



10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Engage the 10 clips and install the instrument cluster center finish panel sub-assembly.



11. INSTALL COMBINATION METER ASSEMBLY


B085782E01
  1. Connect the 2 connectors.

  1. Install the combination meter assembly with the 4 screws.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }



12. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Connect the connectors.

  1. Engage the 6 clips and install the instrument cluster finish panel sub-assembly.

  1. Install the 2 clips.



13. INSTALL NO. 1 LOWER INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



14. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B088394
  1. Connect the hood lock control cable assembly.



    B088397E01
  1. Engage the 2 claws and install the hood lock control lever sub-assembly.



15. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)
  1. Connect all the connectors.

  1. Connect the plug.

  1. Engage the 5 clips and install the radio receiver assembly with bracket.

  1. Install the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



16. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. Connect all the connectors.

  1. Engage the 5 clips and install the radio and display receiver assembly with bracket.

  1. Install the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



17. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    E212050
  1. Connect the 2 connectors.

  1. Engage the 4 clips and install the air conditioning control assembly.



18. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Bench Seat Type)
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B290406
  1. Install the 2 instrument panel cup holders.

  1. Install the box bottom mat.

  1. Install the shift knob.



19. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Bench Seat Type)
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the clip and 2 bolts <A>.



    B290407
  1. Install the 2 instrument panel cup holders.

  1. Install the box bottom mat.

  1. Install the shift knob.



20. INSTALL FRONT CONSOLE BOX (for Manual Transmission on Separate Seat Type)


    E232357
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.

  1. Install the shift knob.



21. INSTALL FRONT CONSOLE BOX (for Automatic Transmission on Separate Seat Type)
  1. Engage the 2 clips and claw, and install the front console box.

  1. Install the 2 screws <F>.



22. INSTALL INSTRUMENT PANEL CUP HOLDER TRAY (for Automatic Transmission on Separate Seat Type)
  1. Engage the 2 clips and 4 claws, and install the instrument panel cup holder tray.

  1. Install the 2 instrument panel cup holders.



23. INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B290408
  1. Engage the 4 claws and install the console box rear.

  1. Install the 2 screws <F> and 2 bolts <B>.

  1. Install the console box carpet.



24. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Manual Transmission on Separate Seat Type)
  1. Engage the 4 clips and claw, and install the console upper panel sub-assembly.



25. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Automatic Transmission on Separate Seat Type)


    B290409
  1. Engage the 6 clips and claw, and install the console upper rear panel.

  1. Install the shift knob.



26. INSTALL INSTRUMENT PANEL HOLE COVER (for Lever Type Parking Brake)
  1. Engage the 4 clips and install the instrument panel hole cover.



27. INSTALL INSTRUMENT PANEL UNDER TRAY (for Pedal Type Parking Brake)
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



28. INSTALL FRONT PILLAR GARNISH RH

HINT:
Follow the same procedures as for the front pillar garnish LH.



29. INSTALL FRONT PILLAR GARNISH LH
  1. Install the 3 wire harness clamps (LH side only).

  1. Engage the claw and clip, and install the front pillar garnish.

  1. Tighten the 2 screws.



    B087471E01
  1. Engage the 2 claws and install the assist grip plug.

    HINT:
    Follow the same procedures as for the opposite side.



30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Follow the same procedures as for the front door opening trim weatherstrip.



31. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



32. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Follow the same procedures as for the cowl side trim board LH.



33. INSTALL COWL SIDE TRIM BOARD LH
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



34. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Follow the same procedures as for the front door scuff plate LH.



35. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 9 claws and install the front door scuff plate.



36. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



37. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }