HOOD > DISASSEMBLY |
| 1. REMOVE CENTER HOOD CUSHION |
![]() |
Remove the 2 center hood cushions.
| 2. REMOVE HOOD BUMPER CUSHION |
![]() |
Rotate counterclockwise and remove the 2 hood bumper cushions.
| 3. REMOVE HOOD TO RADIATOR SUPPORT SEAL |
![]() |
Using a clip remover, remove the 7 clips and hood to radiator support seal.
| 4. REMOVE HOOD BULGE (w/ Hood Bulge) |
![]() |
Remove the 4 nuts.
![]() |
Disengage the 3 clips from the back side of the hood panel.
![]() |
Disengage the 3 guides and remove the hood bulge together with the air intake guide as shown in the illustration.
| 5. REMOVE HOOD AIR INTAKE GUIDE (w/ Hood Bulge) |
![]() |
Disengage the 4 claws and remove the hood air intake guide.
| 6. REMOVE NO. 1 HOOD BULGE PROTECTOR (w/ Hood Bulge) |
![]() |
Remove the 2 No. 1 hood bulge protectors.
| 7. REMOVE NO. 2 HOOD BULGE PROTECTOR (w/ Hood Bulge) |
![]() |
Remove the 2 No. 2 hood bulge protectors.
| 8. REMOVE NO. 3 HOOD BULGE PROTECTOR (w/ Hood Bulge) |
![]() |
Remove the No. 3 hood bulge protector.
| 9. REMOVE WASHER NOZZLE SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and remove the washer nozzle sub-assembly.
Disconnect the washer hose.
| 10. REMOVE WASHER HOSE ASSEMBLY |
![]() |
Separate the washer hose.
Disengage the 3 guides and remove the washer hose.
![]() |
Disengage the 3 claws and remove the washer hose clamps.
![]() |
Disconnect the washer hose.
![]() |
Disengage the claw and remove the windshield washer hose joint.
| 11. REMOVE RADIATOR GRILLE |
![]() |
Remove the 2 screws.
Using a clip remover, remove the 2 clips.
Disengage the 8 guides and remove the radiator grille.
| 12. REMOVE NO. 2 HOOD LOCK RELEASE LEVER PROTECTOR |
![]() |
Adjust the hood position.
Loosen the 4 hinge bolts on the hood side.
Move the hood to adjust the clearance to within the standard range (Step 1).
Tighten the 4 hood side hinge bolts after the adjustment.
![]() |
Adjust the cushion rubber so that the heights of the hood and the fender are aligned.
Raise or lower the hood front end by turning the cushion rubber. Make sure that the clearance is within the standard range.
![]() |
Adjust the hood lock.
Remove the 2 bolts and No. 2 hood lock release lever protector.
![]() |
Loosen the 3 bolts.
![]() |
Adjust the hood lock position so that the striker can enter it smoothly.
![]() |
Tighten the 3 bolts after the adjustment.
![]() |
Install the No. 2 hood lock release lever protector.
| 13. REMOVE HOOD LOCK ASSEMBLY |
![]() |
Remove the 3 bolts.
![]() |
Disconnect the hood lock control cable assembly, then remove the hood lock assembly.
| 14. REMOVE HOOD SUPPORT |
![]() |
Remove the hood support.
Remove the grommet.
![]() |
Using a clip remover, disengage the 2 claws and remove the hood stay holder.
| 15. REMOVE HOOD LOCK CONTROL CABLE PROTECTOR SUB-ASSEMBLY |
![]() |
Remove the 2 nuts, then remove the hood lock control cable protector sub-assembly.
| 16. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the 2 claws.
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.
| 17. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY |
![]() |
Tie a piece of string to the tip of the hood lock control cable assembly.
Remove the hood lock control cable assembly referring to the illustration.
