FRONT DOOR (w/ Power Window) > DISASSEMBLY |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH |
![]() |
Disengage the 3 clips and remove the front door lower frame bracket garnish LH.
| 3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Double Cab) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and clip, then remove the power window regulator master switch assembly.
Disconnect the connector.
| 4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Access Cab) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and clip, then remove the power window regulator master switch assembly.
Disconnect the connector.
| 5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and clip, then remove the power window regulator switch assembly.
Disconnect the connector.
| 6. REMOVE FRONT DOOR TRIM PANEL ASSEMBLY LH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, open the cover.
![]() |
Remove the 2 screws.
![]() |
Disengage the 10 clips and remove the front door trim panel assembly LH.
| 7. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY |
| 8. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY |
| 9. REMOVE FRONT NO. 1 SPEAKER BRACKET |
![]() |
Disconnect the wire harness clamp and connector.
Remove the 3 screws and front No. 1 speaker bracket.
| 10. REMOVE NO. 1 DOOR TRIM BRACKET RH |
![]() |
Remove the 2 screws and No. 1 door trim bracket.
| 11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage claw A as shown in the illustration.
Move the front door inside handle sub-assembly LH in the direction indicated by the arrow mark in the illustration. This will release the claw and allow the removal of the front door inside handle sub-assembly LH.
![]() |
Disconnect the 2 cables from the front door inside handle sub-assembly LH.
| 12. REMOVE FRONT DOOR SERVICE HOLE COVER LH |
![]() |
Remove the front door service hole cover LH.
| 13. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH |
![]() |
Disconnect the outer rear view mirror connector (w/ Power mirror).
Remove the 3 nuts.
Disengage the claw and remove the outer rear view mirror.
| 14. REMOVE FRONT DOOR BELT MOULDING LH |
![]() |
Apply protective tape to the outer circumference of the front door belt moulding, as shown in the illustration.
Using a moulding remover, disengage the 5 claws and remove the front door belt moulding.
| 15. REMOVE FRONT DOOR INSIDE PANEL PLATE LH |
![]() |
Remove the 4 screws and front door inside panel plate LH.
| 16. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH |
![]() |
Driver side: Connect the power window regulator master switch.
Passenger side: Connect the power window regulator switch.
Move the front door glass sub-assembly LH until the 2 bolts appear in the service holes.
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly LH in the direction indicated by the arrow marks in the illustration.
Driver side: Disconnect the power window regulator master switch.
Passenger side: Disconnect the power window regulator switch.
| 17. REMOVE FRONT DOOR GLASS RUN LH |
![]() |
Remove the front door glass run LH.
| 18. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
![]() |
Disconnect the front door power window regulator connector.
Loosen bolt A.
Remove the 5 bolts, then remove the front door window regulator sub-assembly LH.
| 19. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
![]() |
Place matchmarks on the power window regulator motor gear and regulator gear.
Using a torx driver T25, remove the 3 screws and power window regulator motor assembly LH.
| 20. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH |
![]() |
Remove the 2 bolts, then remove the front door rear lower frame sub-assembly LH.
| 21. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH |
![]() |
Remove the 2 nuts, then remove the front door front lower frame sub-assembly LH.
| 22. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH |
![]() |
Remove the hole plug.
Using a torx socket wrench T30, loosen the screw and remove the front door outside handle cover LH.
| 23. REMOVE FRONT DOOR LOCK ASSEMBLY LH |
![]() |
Disconnect the front door lock connector.
Using a torx socket wrench T30, remove the 3 screws, then remove the front door lock assembly LH.
| 24. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH |
![]() |
Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow mark in the illustration.
![]() |
Disengage the 3 claws and remove the front door outside handle front pad.
![]() |
Disengage the 2 claws and remove the front door outside handle rear pad.
| 25. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH |
![]() |
Using a torx socket wrench T30, loosen the screw.
Slide the outside handle frame sub-assembly to remove it.
| 26. REMOVE FRONT DOOR CHECK ASSEMBLY LH |
![]() |
Remove the 2 nuts and bolt, then remove the front door check assembly LH.
| 27. REMOVE FRONT DOOR WEATHERSTRIP LH (for Double Cab) |
![]() |
Disengage the 34 clips and remove the front door weatherstrip LH.
| 28. REMOVE FRONT DOOR WEATHERSTRIP LH (for Access Cab) |
![]() |
Disengage the 36 clips and remove the front door weatherstrip LH.