REAR DOOR (for Double Cab) > REASSEMBLY |
| 1. INSTALL REAR DOOR WEATHERSTRIP LH |
![]() |
Engage the 32 clips and install a new rear door weatherstrip LH.
![]() |
Engage the 2 clips.
Remove the tab tape at both ends of 2-sided tape attached to the weather strip, and attach the weather strip to the door panel with the 2-sided tape.
| 2. INSTALL REAR DOOR CHECK ASSEMBLY LH |
![]() |
Apply MP grease to the sliding areas of the check.
Install the rear door check assembly onto the door panel with the 2 nuts.
Apply adhesive to the threads of the bolt.
Install the rear door check assembly onto the body panel with the bolt.
| 3. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH |
Apply MP grease to the sliding areas of the rear door outside handle frame sub-assembly LH.
![]() |
Using a torx socket wrench T30 , install the handle frame sub-assembly with the screw.
| 4. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH |
![]() |
Engage the 2 claws and install the outside handle rear pad.
![]() |
Engage the 3 claws and install the outside handle front pad.
![]() |
Pushing the outside handle in the direction of the arrow marks shown in the illustration, install the outside handle.
| 5. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH |
![]() |
Using a torx socket wrench T30 , install the rear door outside handle cover with the screw.
| 6. INSTALL REAR DOOR LOCK ASSEMBLY LH |
Apply MP grease to the sliding and rotating areas of the rear door lock assembly.
Install a new door lock wire harness packing.
![]() |
Pull and hold the release plate of the outside handle frame, as shown in the illustration.
![]() |
Apply adhesive to the threads of the 3 screws.
Using a torx socket wrench T30 , install the rear door lock with the 3 screws.
Connect the connector.
| 7. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
![]() |
Using a torx socket wrench T25 , install the power window regulator motor assembly LH with the 3 screws.
| 8. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly LH.
![]() |
Loosely screw bolt A onto the rear door window regulator sub-assembly LH.
Insert the rear door window regulator into the door panel. Use bolt A to hang the rear door window regulator on the door panel.
Install the rear door window regulator with the 5 bolts, and tighten bolt A.
| 9. INSTALL REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH |
![]() |
Install the rear door front window guide sub-assembly LH with the bolt.
| 10. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH |
![]() |
Install the rear door rear lower window frame sub-assembly LH with the 2 bolts.
![]() |
Install the hole plug.
| 11. INSTALL REAR DOOR GLASS RUN LH |
![]() |
Install the rear door glass run LH.
| 12. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH |
![]() |
Install the rear door glass sub-assembly LH onto the rear door window regulator sub-assembly LH with the 2 bolts.
| 13. INSTALL REAR DOOR BELT MOULDING LH |
![]() |
Engage the 6 claws and install a new front door belt molding.
| 14. INSTALL REAR DOOR SERVICE HOLE COVER LH |
![]() |
Apply butyl tape to the door panel, then install the rear door service hole cover LH as shown in the illustration.
| 15. INSTALL NO. 2 REAR DOOR TRIM BRACKET |
![]() |
Install the No. 2 rear door trim bracket with the 3 screws.
| 16. INSTALL REAR SPEAKER ASSEMBLY |
![]() |
Install the rear speaker assembly with the 3 screws.
Connect the connector.
| 17. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH |
![]() |
Connect the 2 cables to the rear door inside handle sub-assembly LH.
![]() |
Engage the 3 claws and install the rear door inside handle sub-assembly LH onto the door panel.
| 18. INSTALL REAR DOOR TRIM PANEL ASSEMBLY LH |
![]() |
Engage the 9 clips and install the rear door trim panel assembly LH.
Install the door assist grip assembly LH with the screw.
| 19. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY |
![]() |
Connect the connector.
![]() |
Engage the 2 claws and install the rear power window regulator switch assembly.
| 20. INSTALL REAR DOOR FRAME GARNISH LH |
![]() |
Engage the 4 clips and install the rear door frame garnish LH.
| 21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |