Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 4WD)

FRONT DRIVE SHAFT ASSEMBLY (for 4WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT


F042771
  1. Coat the spline of the inboard joint shaft with gear oil.

  1. Align the shaft splines and install the front drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing downward.
    2. Be careful not to damage the oil seal.

    HINT:
    Whether the inboard joint shaft is in contact with the pinion shaft or not can be confirmed from the sound or feeling when driving it.



2. INSTALL FRONT SUSPENSION LOWER ARM
  1. Install the front lower ball joint attachment with the 2 bolts.

    Torque:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }



3. INSTALL FRONT AXLE HUB NUT
  1. Install the front axle hub nut.

    Torque:
    235 N*m{ 2396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and a new cotter pin.

  1. Install the front axle hub grease cap.



4. INSTALL TIE ROD END SUB-ASSEMBLY
  1. Install the tie rod end sub-assembly to the steering knuckle.

  1. Install the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.



5. INSTALL FRONT SPEED SENSOR
  1. Install the speed sensor wire harness to the steering knuckle with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Engage the 2 clamps.

  1. Install the front speed sensor with the bolt.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }



6. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1152 kgf*cm , 83 ft.*lbf }



7. ADD DIFFERENTIAL OIL


D025304E37
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the differential carrier assembly with differential gear oil.

    Oil type and viscosity:
    Toyota Genuine Differential gear oil LT APL 75W-85 GL-5 or equivalent.

    Capacity:
    Front differential carrier assembly:
    1.45 to 1.55 liters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)
    Rear differential carrier assembly (for 2WD):
    3.26 to 3.36 liters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Rear differential carrier assembly (for Pre, 4WD):
    2.75 to 2.85 liters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



8. INSPECT DIFFERENTIAL OIL


D025304E37
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the differential carrier assembly with differential gear oil.

    Oil type and viscosity:
    Toyota Genuine Differential gear oil LT APL 75W-85 GL-5 or equivalent.

    Capacity:
    Front differential carrier assembly:
    1.45 to 1.55 liters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)
    Rear differential carrier assembly (for 2WD):
    3.26 to 3.36 liters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Rear differential carrier assembly (for Pre, 4WD):
    2.75 to 2.85 liters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



9. INSPECT SPEED SENSOR SIGNAL (for Hydraulic Brake Booster)
(Click here)


10. INSPECT SPEED SENSOR SIGNAL (for Vacuum Brake Booster)
(Click here)


11. INSPECT FOR DIFFERENTIAL OIL LEAK


12. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)