Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB (for 4WD and Pre-Runner)

FRONT AXLE HUB (for 4WD and Pre-Runner) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT AXLE HUB


2. INSTALL FRONT SUSPENSION UPPER ARM


G020157
  1. Install a new nut and clip.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }



3. INSTALL FRONT SUSPENSION LOWER ARM


F051497
  1. Install the front suspension lower arm with the 2 bolts.

    Torque:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }



4. INSTALL TIE ROD END SUB-ASSEMBLY


F043604
  1. Install the tie rod end with the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes in the cotter pin are not aligned, tighten the nut an additional 60°.



5. INSTALL FRONT STABILIZER LINK ASSEMBLY


C099158
  1. Install the stabilizer link onto the steering knuckle with the nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud.



6. INSTALL FRONT AXLE HUB NUT (for 4WD)


F042732
  1. Install the hub nut.

    Torque:
    235 N*m{ 2396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and cotter pin.



7. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)


8. INSTALL FRONT DISC


9. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


F043121
  1. Install the front disc brake caliper with the 2 bolts.

    Torque:
    123 N*m{ 1254 kgf*cm , 91 ft.*lbf }



    F052164
  1. Install the brake tube bracket onto the steering knuckle with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    F043120
  1. Using a union nut wrench, connect the brake tube to the disc brake cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



10. INSTALL FRONT SPEED SENSOR


F052163E03
  1. Install the speed sensor wire harness onto the steering knuckle with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Engage the 2 clips.

  1. Install the speed sensor with the bolt.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }



11. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1152 kgf*cm , 83 ft.*lbf }



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

(Click here)


13. FILL RESERVOIR WITH BRAKE FLUID (for Hydraulic Brake Booster)

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



14. FILL RESERVOIR WITH BRAKE FLUID (for Vacuum Brake Booster)


C187250

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



15. BLEED MASTER CYLINDER (for Vacuum Brake Booster)
Click here

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C187279
  1. Using a union nut wrench, separate the brake tubes from the master cylinder.



    C187251
  1. Slowly depress the brake pedal and hold it there (Step A).



    C187252
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C187280E01
  1. Using a union nut wrench, install the brake tubes into the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 187 kgf*cm , 13 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 20 mm (0.787 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



16. BLEED BRAKE LINE (for Hydraulic Brake Booster)
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



17. BLEED BRAKE LINE (for Vacuum Brake Booster)


C187268
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



18. INSPECT FLUID LEVEL IN RESERVOIR (for Hydraulic Brake Booster)


    C172184
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 40 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



19. INSPECT FLUID LEVEL IN RESERVOIR (for Vacuum Brake Booster)


A261799
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



20. INSPECT FOR BRAKE FLUID LEAK


21. CHECK VSC SENSOR SIGNAL (for Hydraulic Brake Booster)
(Click here)


22. CHECK VSC SENSOR SIGNAL (for Vacuum Brake Booster)
(Click here)


23. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)