Home › SUSPENSION & AXLE › AXLE › REAR AXLE SHAFT

REAR AXLE SHAFT > INSTALLATION

for Preparation Click here



1. INSTALL REAR AXLE SHAFT OIL SEAL


F052141E01
  1. Using SST and a hammer, install a new oil seal.

    SST
    09950-60020   (09951-00770)
    09950-70010   (09951-07150)



2. INSTALL REAR AXLE SHAFT WITH BACKING PLATE


F052131
  1. Install a new O-ring.

  1. Install the rear axle shaft with backing plate with the 4 nuts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



3. INSTALL REAR BRAKE TUBE NO. 8


F052272
  1. Using a union nut wrench, connect the brake tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



4. INSTALL PARKING BRAKE CABLE ASSEMBLY NO. 3


D028121
  1. Install the parking brake cable with the 2 bolts onto the backing plate.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL REAR SPEED SENSOR


F050583
  1. Install the rear speed sensor with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Make sure that the sensor tip is clean.

  1. Connect the speed sensor connector.



6. APPLY HIGH TEMPERATURE GREASE


C179335E01
  1. Apply high temperature grease to the shoe attached surface of the backing plate.



7. INSTALL REAR BRAKE SHOE


C179336E01
  1. Apply high temperature grease to the adjusting bolt.



    F050550
  1. Install the parking brake shoe lever LH and parking brake shoe strut set with the shoe return spring onto the rear brake shoe.



    F050544
  1. Using pliers, install the parking brake shoe strut set, parking brake reaction lever and parking brake shoe lever LH with 2 new C-washers.



    F042688
  1. Using needle-nose pliers, connect the parking brake cable No. 3 to the parking brake shoe lever LH.



    F050543E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



8. INSTALL FRONT BRAKE SHOE
  1. Install the automatic adjust lever LH, automatic adjust lever spring and parking brake shoe strut lower onto the front brake shoe.



    F050542E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



    F042698
  1. Install the tension spring onto the front brake shoe and rear brake shoe.



    F050551
  1. Using needle-nose pliers, install the return spring.



    F050540E01
  1. Using SST, install the shoe return spring onto the front brake shoe.

    SST
    09921-00010  



9. INSPECT REAR DRUM BRAKE INSTALLATION


  1. Check that each part is installed properly.


    F050552E01



    F050553E01
  1. Measure the brake drum inside diameter and the diameter of the brake shoes. Check that difference between the diameters is the specified shoe clearance.

    Shoe clearance:
    0.5 mm (0.0197 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and the drum.



10. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
  1. Install a new drum gasket onto the rear brake drum.

  1. Install the rear brake drum.



11. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


F040023E02
  1. Provisionally install the hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 15 notches.

  1. Install the hole plug.



12. INSTALL REAR WHEEL

Torque:
113 N*m{ 1152 kgf*cm , 83 ft.*lbf }



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

(Click here)


14. FILL RESERVOIR WITH BRAKE FLUID (for Hydraulic Brake Booster)

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



15. FILL RESERVOIR WITH BRAKE FLUID (for Vacuum Brake Booster)


C187250

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



16. BLEED MASTER CYLINDER (for Vacuum Brake Booster)
Click here

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C187279
  1. Using a union nut wrench, separate the brake tubes from the master cylinder.



    C187251
  1. Slowly depress the brake pedal and hold it there (Step A).



    C187252
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C187280E01
  1. Using a union nut wrench, install the brake tubes into the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 187 kgf*cm , 13 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 20 mm (0.787 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



17. BLEED BRAKE LINE (for Hydraulic Brake Booster)
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



18. BLEED BRAKE LINE (for Vacuum Brake Booster)


C187268
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



19. INSPECT FLUID LEVEL IN RESERVOIR (for Hydraulic Brake Booster)


    C172184
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 40 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



20. INSPECT FLUID LEVEL IN RESERVOIR (for Vacuum Brake Booster)


A261799
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



21. INSPECT FOR BRAKE FLUID LEAK


22. INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission)
  1. Slowly depress the parking brake pedal to the fully applied position, and count the number of clicks.

    Parking brake pedal travel at 300 N (31 kgf, 67 lbf):
    7 to 10 clicks



23. INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transmission)
  1. Slowly pull the parking brake lever to the fully applied position, and count the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    7 to 10 clicks



24. ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transmission)
  1. Confirm that the parking brake pedal is released.



    F050697E01
  1. Loosen the lock nut (labeled A) and turn the adjusting nut (labeled B) until the parking brake pedal travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on.



25. ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transmission)
  1. Confirm that the parking brake lever is released.



    F050697E01
  1. Loosen the lock nut (labeled A) and turn the adjusting nut (labeled B) until the parking brake lever travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the parking brake lever indicator light comes on.



26. CHECK VSC SENSOR SIGNAL (for Hydraulic Brake Booster)
(Click here)


27. CHECK VSC SENSOR SIGNAL (for Vacuum Brake Booster)
(Click here)