Home › BRAKE › BRAKE › BRAKE PEDAL

BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL PAD
  1. Install the brake pedal pad onto the brake pedal.



2. INSTALL BRAKE PEDAL LEVER
  1. Apply lithium soap base glycol grease to the 2 brake pedal link pins, 2 pedal shaft collars and 2 brake pedal links.

  1. Install the brake pedal lever with the 2 brake pedal link pins, 2 brake pedal shaft collars and 2 brake pedal links onto the brake pedal.

  1. Install 2 new E-rings onto each brake pedal link pin.



3. INSTALL BRAKE PEDAL
  1. Apply lithium soap base glycol grease to the 2 collars and 4 brake pedal bushes.

  1. Install the 2 collars and 4 brake pedal bushes onto the brake pedal and brake pedal lever.



    C187264
  1. Install the brake pedal with the bolt and nut onto the brake pedal support.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



4. INSTALL STOP LIGHT SWITCH ASSEMBLY


C187267E01
  1. Insert the stop light switch until the body comes into contact with the cushion.

    NOTICE:
    When inserting the stop light switch, support the pedal from behind so that the pedal is not pushed in.



    C187262E01
  1. Make a quarter turn clockwise to install the stop light switch.

    NOTICE:
    The turning torque for installing the stop light switch:

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

  1. Check the protrusion of the rod.

    Protrusion of the rod:
    0.5 to 2.6 mm (0.020 to 0.102 in.)



5. INSTALL BRAKE PEDAL RETURN SPRING
  1. Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal support and brake pedal.

  1. Install the return spring onto the brake pedal support and brake pedal.



6. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY


C187263
  1. Install the 4 nuts and brake pedal support.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

  1. Connect the stop light switch connector to the stop lamp switch.



7. INSTALL BRAKE PEDAL SUPPORT REINFORCEMENT
  1. Install the reinforcement onto the brake pedal support.



    C187271
  1. Temporarily install the bolt and nut to the brake pedal support, reinforcement and brake pedal lever.



    C187270
  1. Install the bolt onto the reinforcement.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }

  1. Tighten the bolt and nut to the brake pedal support, reinforcement and brake pedal lever.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



8. INSTALL MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.

  1. Install the push rod clevis onto the brake pedal lever with the push rod pin and clip.



9. INSPECT BRAKE PEDAL HEIGHT


C187248E01
  1. Check the brake pedal height.

    Pedal height from dash panel:
    Type
    Pedal Height
    Hydraulic brake booster
    158.6 to 168.6 mm (6.25 to 6.63 in.)
    Vacuum brake booster,
    Automatic transmission
    159.8 to 169.8 mm (6.30 to 6.68 in.)
    Vacuum brake booster,
    Manual transmission
    156.6 to 166.6 mm (6.17 to 6.55 in.)

    NOTICE:
    Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

    If the pedal height is incorrect, adjust the rod operating adapter length.



    C189741E01
  1. Adjust the rod operating adapter length.

    1. Remove the clip and clevis pin.

    2. Loosen the clevis lock nut.

    3. Adjust the rod operating adapter length by turning the pedal push rod clevis.

      Rod operating adapter length A:
      for Hydraulic brake booster:
      214 to 224 mm (8.425 to 8.818 in.)
      for Vacuum brake booster:
      213 to 223 mm (8.386 to 8.780 in.)

    4. Tighten the clevis lock nut.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

    5. Install the clip and clevis pin.

      1. If the pedal height is incorrect even when the rod operating adapter is adjusted, check that there is no damage in the brake pedal, brake pedal lever, brake pedal bracket or dash panel.
      2. Even if there is damage, there is no problem if the reserve distance is within the standard value.
      3. If necessary, replace the parts.



10. INSPECT PEDAL FREE PLAY


C189744E01
  1. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.

  1. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

    Pedal free play:
    1 to 6 mm (0.04 to 0.24 in.)



11. INSPECT PEDAL RESERVE DISTANCE


R000934E10
  1. Release the parking brake pedal.
    With the engine running, depress the pedal and measure the pedal reserve distance as shown.

    Pedal reserve distance from asphalt sheet at 490 N (50 kgf, 110.2 lbf):
    More than 55 mm (2.17 in.)

    If incorrect, troubleshoot the brake system.



12. INSTALL DRIVER SIDE JUNCTION BLOCK

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



13. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



14. INSTALL INSTRUMENT PANEL UNDER TRAY (for Automatic Transmission)
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



15. INSTALL INSTRUMENT PANEL HOLE COVER (for Manual Transmission)
  1. Engage the 4 clips and install the instrument panel hole cover.



16. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



17. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



18. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



19. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)
  1. Engage the 8 claws and clip, and install the front door scuff plate.



20. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab)
  1. Engage the 9 claws and clip, and install the front door scuff plate.



21. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab)
  1. Engage the 9 claws and install the front door scuff plate.



22. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.



23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }