BRAKE PEDAL > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT FLOOR FOOTREST |
![]() |
Disengage the 2 clips and remove the front floor footrest.
| 3. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
![]() |
Disengage the 8 claws and clip, and remove the front door scuff plate.
| 4. REMOVE FRONT DOOR SCUFF PLATE LH (for Access Cab) |
![]() |
Disengage the 9 claws and clip, and remove the front door scuff plate.
| 5. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab) |
![]() |
Disengage the 9 claws and remove the front door scuff plate.
| 6. REMOVE COWL SIDE TRIM BOARD LH (for Regular Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 7. REMOVE COWL SIDE TRIM BOARD LH (for Access Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 8. REMOVE COWL SIDE TRIM BOARD LH (for Double Cab) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim board.
| 9. REMOVE INSTRUMENT PANEL UNDER TRAY (for Automatic Transmission) |
![]() |
Disengage the 4 clips and 2 claws, and remove the instrument panel under tray.
| 10. REMOVE INSTRUMENT PANEL HOLE COVER (for Manual Transmission) |
![]() |
Disengage the 4 clips and remove the instrument panel hole cover.
| 11. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
![]() |
Remove the 2 bolts <B>.
Disengage the 3 clips and remove the lower No. 1 instrument panel finish panel.
Disconnect the connectors.
| 12. SEPARATE DRIVER SIDE JUNCTION BLOCK |
| 13. SEPARATE MASTER CYLINDER PUSH ROD CLEVIS |
![]() |
Remove the clip and push rod pin, and then separate the push rod clevis.
| 14. REMOVE BRAKE PEDAL SUPPORT REINFORCEMENT |
![]() |
Remove the bolt from the reinforcement.
![]() |
Remove the bolt and nut, and then remove the reinforcement from the brake pedal support.
| 15. REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY |
Disconnect the stop light switch connector from the stop lamp switch.
![]() |
Remove the 4 nuts and brake pedal support.
| 16. REMOVE BRAKE PEDAL RETURN SPRING |
![]() |
Remove the return spring from the brake pedal support and brake pedal.
| 17. REMOVE STOP LIGHT SWITCH ASSEMBLY |
Turn the stop light switch counterclockwise, and remove the stop light switch.
Remove the stop light switch mounting adjuster from the brake pedal support.
| 18. REMOVE BRAKE PEDAL |
![]() |
Remove the bolt and nut, and then remove the brake pedal from the brake pedal support.
Remove the 4 brake pedal bushes from the brake pedal and brake pedal lever.
Remove the 2 collars from the brake pedal and brake pedal lever.
| 19. REMOVE BRAKE PEDAL LEVER |
![]() |
Using a screwdriver, remove the 2 E-rings from the brake pedal link pin.
Remove the 2 brake pedal link pins, 2 brake pedal shaft collars and 2 brake pedal links.
Remove the brake pedal lever from the brake pedal.
| 20. REMOVE BRAKE PEDAL PAD |
Remove the brake pedal pad from the brake pedal.