Home › BRAKE › BRAKE › FRONT BRAKE (for 2WD)

FRONT BRAKE (for 2WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DISC
  1. Aligning the matchmarks, install the front disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the minimum runout.



2. INSPECT DISC RUNOUT


C179332
  1. Provisionally fasten the disc with the hub nuts.

    Torque:
    113 N*m{ 1152 kgf*cm , 83 ft.*lbf }

  1. Using a dial indicator, measure the disc runout 10 mm (0.394 in.) away from the outer edge of the disc.

    Maximum disc runout:
    0.05 mm (0.00197 in.)

  1. If the disc runout is the maximum value or greater, check the bearing play in the axial direction and check the axle hub runout . If the bearing play and axle hub runout are normal, adjust the disc runout or grind it on an on-car brake lathe.



3. INSTALL FRONT DISC BRAKE BUSH DUST BOOT


F051233
  1. Place soft jaws on a vise and hold the disc brake cylinder mounting in the vise through aluminum plates.

  1. Apply lithium soap base glycol grease to the sealing surface of 2 new front disc brake bush dust boots.

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bush dust boot.

  1. Using a socket wrench (19 mm) and hammer, tap the 2 disc brake bush dust boots into the disc brake cylinder mounting.



4. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING


F051225
  1. Install the disc brake cylinder mounting with the 2 bolts.

    Torque:
    108 N*m{ 1101 kgf*cm , 80 ft.*lbf }



5. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH
  1. Apply lithium soap base glycol grease to a new disc brake cylinder slide bush.

  1. Install the disc brake cylinder slide bush to the bottom side of the disc brake cylinder slide pin (No. 2).



6. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN


    C190224E02
  1. Apply lithium soap base glycol grease to the sliding part and the sealing surface of the disc brake cylinder slide pin.



    F051223E01
  1. Install the disc brake cylinder slide pin onto the disc brake cylinder mounting.



7. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
  1. Install the 2 disc brake pad support plates onto the disc brake cylinder mounting.



8. INSTALL ANTI SQUEAL SHIM KIT FRONT

NOTICE:
If necessary, replace the anti-squeal shim kit when replacing the brake pad.



    C190225E01
  1. Apply disc brake grease to the both surfaces of the 2 anti-squeal shims and install them.

  1. Install the 2 outside anti-squeal shims onto the brake pads.

  1. Install the pad wear indicator plate facing upward, and install each pad.



9. INSTALL DISC BRAKE PAD KIT FRONT
  1. Install the 2 disc brake pads with anti-squeal shim onto the disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the brake pads or the front disc.



10. INSTALL DISC BRAKE CYLINDER ASSEMBLY


F051222
  1. Install the disc brake cylinder with the 2 bolts.

    Torque:
    36 N*m{ 370 kgf*cm , 27 ft.*lbf }



    F050588
  1. Install the flexible hose with a new union bolt and a new gasket.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



11. FILL RESERVOIR WITH BRAKE FLUID


C187250

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



12. BLEED MASTER CYLINDER
Click here

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C187279
  1. Using a union nut wrench, separate the brake tubes from the master cylinder.



    C187251
  1. Slowly depress the brake pedal and hold it there (Step A).



    C187252
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C187280E01
  1. Using a union nut wrench, install the brake tubes into the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 187 kgf*cm , 13 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 20 mm (0.787 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



13. BLEED BRAKE LINE


C187268
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



14. BLEED BRAKE ACTUATOR

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with the Techstream by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the Techstream to the DLC3, and turn the ignition switch ON.

    NOTICE:
    Do not start the engine.

  1. Select "Air Bleeding" on the Techstream.

    HINT:
    Refer to the Techstream operator's manual for further details.



  1. Bleed the air out of the brake line when Step 1: Increase appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to either one of the bleeder plugs.



    2. C187268
    3. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    4. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    5. Repeat steps E and F until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug completely.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2: Inhalation appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the Techstream (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the Techstream display and tighten the bleeder plug (Step H).

    4. Repeat steps G and H until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the Techstream, operate the brake actuator assembly, completely depress the brake pedal and hold it there (Step J).

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, and then release the brake pedal (Step K).

    5. Repeat steps I to K until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.



  1. Bleed the air out of the brake line again when Step 4: Increase appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to either one of the bleeder plugs.



    2. C187268
    3. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step L).

    4. When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step M).

    5. Repeat steps L and M until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    8. Make sure that the air bleeding is complete by referring to the Techstream display and turn off the Techstream.

    9. Disconnect the Techstream from the DLC3.

    10. Turn the ignition switch off.



15. INSPECT CHECK FLUID LEVEL IN RESERVOIR


A261799
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



16. INSPECT FOR BRAKE FLUID LEAK


17. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1152 kgf*cm , 83 ft.*lbf }