Home › BRAKE › BRAKE › FRONT BRAKE (for 4WD and Pre-Runner)

FRONT BRAKE (for 4WD and Pre-Runner) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DISC
  1. Aligning the matchmarks, install the front disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the minimum runout.



2. INSPECT DISC RUNOUT


C179333
  1. Provisionally fasten the disc with the hub nuts.

    Torque:
    113 N*m{ 1152 kgf*cm , 83 ft.*lbf }

  1. Using a dial indicator, measure the disc runout 10 mm (0.394 in.) away from the outer edge of the disc.

    Maximum disc runout:
    0.05 mm (0.00197 in.)

  1. If the disc runout is the maximum value or greater, check the bearing play in the axial direction and check the axle hub runout . If the bearing play and axle hub runout are normal, adjust the disc runout or grind it on an on-car brake lathe.



3. INSTALL DISC BRAKE CYLINDER ASSEMBLY


F043121
  1. Install the disc brake cylinder assembly with the 2 bolts.

    Torque:
    123 N*m{ 1254 kgf*cm , 91 ft.*lbf }



    F043120
  1. Using a union nut wrench, connect the brake tube to the disc brake cylinder.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



4. INSTALL ANTI SQUEAL SHIM KIT FRONT

NOTICE:
If necessary, replace the anti-squeal shim kit when replacing the brake pad.

  1. Install the anti-squeal shims on to each brake pad.



5. INSTALL DISC BRAKE PAD KIT FRONT
  1. Install the 2 disc brake pads with anti-squeal shim onto the disc brake cylinder.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the brake pads and the front disc.



6. INSTALL FRONT DISC BRAKE ANTI RATTLE WITH HOLE PIN


F043185E01
  1. Install the 2 anti rattle w/ hole pins and anti-rattle spring onto the disc brake cylinder.

    HINT:
    The anti-rattle spring is installed onto the lower anti-rattle w/ hole pin.

  1. Install the 2 new pin hold clips with the anti-rattle w/ hole pin.

    NOTICE:
    Be sure to install the pin hold clip with the handle facing to the vehicle center.



7. FILL RESERVOIR WITH BRAKE FLUID (for Hydraulic Brake Booster)

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



8. FILL RESERVOIR WITH BRAKE FLUID (for Vacuum Brake Booster)


C187250

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



9. BLEED BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY (for Hydraulic Brake Booster)

HINT:
If the brake master cylinder is disassembled, the brake line is disconnected from the brake master cylinder or if the reservoir becomes empty, bleed the brake master cylinder.

  1. Turn the ignition switch to ON, and wait until the pump motor has stopped (step A).

    HINT:
    Pump operating sound can be heard.

  1. Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (step B).

    HINT:
    When pressure in the accumulator is released, the reaction force becomes lighter and the stroke becomes longer.

  1. Repeat step A and B 5 times (step C).

  1. Turn the ignition switch to ON, and check that the pump stops after approximately 8 to 14 seconds.

    NOTICE:
    If the pump does not stop, repeat step C again.



10. BLEED MASTER CYLINDER (for Vacuum Brake Booster)
Click here

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C187279
  1. Using a union nut wrench, separate the brake tubes from the master cylinder.



    C187251
  1. Slowly depress the brake pedal and hold it there (Step A).



    C187252
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C187280E01
  1. Using a union nut wrench, install the brake tubes into the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 187 kgf*cm , 13 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 20 mm (0.787 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



11. BLEED BRAKE LINE (for Hydraulic Brake Booster)
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



12. BLEED BRAKE LINE (for Vacuum Brake Booster)


C187268
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



13. BLEED MASTER CYLINDER SOLENOID (for Hydraulic Brake Booster)

HINT:
If the brake master cylinder is disassembled, the brake line is disconnected from the brake master cylinder or if the reservoir become empty, bleed the brake master cylinder.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select "Active Test" mode on the Techstream.



    C187268
  1. Connect the vinyl tube to the rear wheel cylinder.

  1. Loosen the bleeder plug.

  1. Select "TRAC Solenoid (SRMF & SRMR)" to drive the solenoids and bleed air from the rear wheel cylinder (step F).

    NOTICE:
    1. Do not depress the brake pedal.
    2. Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    HINT:
    1. Brake fluid is sent through the pump.
    2. To protect the solenoids, the Techstream turns OFF automatically 2 seconds after every solenoid has been turned ON.

  1. Repeat step F until all the air in the brake fluid is bled out.

  1. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedures to bleed the other brake line.

  1. Turn the ignition switch to OFF.

  1. Turn the ignition switch to ON.

  1. Clear DTC (Click here).



14. BLEED BRAKE ACTUATOR (for Vacuum Brake Booster)

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with the Techstream by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the Techstream to the DLC3, and turn the ignition switch ON.

    NOTICE:
    Do not start the engine.

  1. Select "Air Bleeding" on the Techstream.

    HINT:
    Refer to the Techstream operator's manual for further details.



  1. Bleed the air out of the brake line when Step 1: Increase appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to either one of the bleeder plugs.



    2. C187268
    3. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    4. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    5. Repeat steps E and F until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug completely.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2: Inhalation appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the Techstream (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the Techstream display and tighten the bleeder plug (Step H).

    4. Repeat steps G and H until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the Techstream, operate the brake actuator assembly, completely depress the brake pedal and hold it there (Step J).

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, and then release the brake pedal (Step K).

    5. Repeat steps I to K until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.



  1. Bleed the air out of the brake line again when Step 4: Increase appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to either one of the bleeder plugs.



    2. C187268
    3. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step L).

    4. When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step M).

    5. Repeat steps L and M until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    8. Make sure that the air bleeding is complete by referring to the Techstream display and turn off the Techstream.

    9. Disconnect the Techstream from the DLC3.

    10. Turn the ignition switch off.



15. INSPECT FLUID LEVEL IN RESERVOIR (for Hydraulic Brake Booster)


    C172184
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 40 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



16. INSPECT FLUID LEVEL IN RESERVOIR (for Vacuum Brake Booster)


A261799
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



17. INSPECT FOR BRAKE FLUID LEAK


18. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1152 kgf*cm , 83 ft.*lbf }