HYDRAULIC BRAKE BOOSTER > INSTALLATION |
| 1. INSTALL HYDRAULIC BRAKE BOOSTER |
![]() |
Install a new brake booster gasket onto the hydraulic brake booster.
Install the hydraulic brake booster with the 4 nuts.
![]() |
Using a union nut wrench, connect the 4 brake lines to the correct positions of the hydraulic brake booster, as shown in the illustration.
![]() |
Connect the 3 connectors.
| 2. INSTALL MASTER CYLINDER PUSH ROD CLEVIS |
Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.
Install the push rod clevis onto the brake pedal lever with the push rod pin and clip.
| 3. INSTALL DRIVER SIDE JUNCTION BLOCK |
| 4. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Connect the connectors.
Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.
Install the 2 bolts <B>.
| 5. INSTALL INSTRUMENT PANEL UNDER TRAY (for Automatic Transmission) |
Engage the 4 clips and 2 claws, and install the instrument panel under tray.
| 6. INSTALL INSTRUMENT PANEL HOLE COVER (for Manual Transmission) |
Engage the 4 clips and install the instrument panel hole cover.
| 7. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 8. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 9. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab) |
Engage the 2 clips and install the cowl side trim board.
Install the clip.
| 10. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
Engage the 8 claws and clip, and install the front door scuff plate.
| 11. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab) |
Engage the 9 claws and clip, and install the front door scuff plate.
| 12. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab) |
Engage the 9 claws and install the front door scuff plate.
| 13. INSTALL FRONT FLOOR FOOTREST |
![]() |
Engage the 2 clips and install the front floor footrest.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 15. INSPECT BRAKE PEDAL HEIGHT |
![]() |
Check the brake pedal height.
| Type | Pedal Height |
| Hydraulic brake booster | 158.6 to 168.6 mm (6.25 to 6.63 in.) |
| Vacuum brake booster, Automatic transmission | 159.8 to 169.8 mm (6.30 to 6.68 in.) |
| Vacuum brake booster, Manual transmission | 156.6 to 166.6 mm (6.17 to 6.55 in.) |
![]() |
Adjust the rod operating adapter length.
Remove the clip and clevis pin.
Loosen the clevis lock nut.
Adjust the rod operating adapter length by turning the pedal push rod clevis.
Tighten the clevis lock nut.
Install the clip and clevis pin.
| 16. INSPECT PEDAL FREE PLAY |
![]() |
Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.
Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.
| 17. INSPECT PEDAL RESERVE DISTANCE |
![]() |
Release the parking brake pedal.
With the engine running, depress the pedal and measure the pedal reserve distance as shown.
| 18. FILL RESERVOIR WITH BRAKE FLUID |
| 19. BLEED BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY |
Turn the ignition switch to ON, and wait until the pump motor has stopped (step A).
Turn the ignition switch to OFF, and depress the brake pedal more than 20 times (step B).
Repeat step A and B 5 times (step C).
Turn the ignition switch to ON, and check that the pump stops after approximately 8 to 14 seconds.
| 20. BLEED BRAKE LINE |
Turn the ignition switch to ON, and wait until the pump motor has stopped.
![]() |
Front brake line.
Connect the vinyl tube to the brake caliper.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).
At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).
Repeat step D and E until all the air in the fluid has been bled out.
Repeat the above procedures to bleed the other brake line.
![]() |
Rear brake line.
Connect the vinyl tube to the wheel cylinder.
Depress the brake pedal, hold it, and then loosen the bleeder plug.
Loosen the bleeder plug and release air.
When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.
Repeat the above procedures to bleed the other brake line.
| 21. BLEED MASTER CYLINDER SOLENOID |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select "Active Test" mode on the Techstream.
![]() |
Connect the vinyl tube to the rear wheel cylinder.
Loosen the bleeder plug.
Select "TRAC Solenoid (SRMF & SRMR)" to drive the solenoids and bleed air from the rear wheel cylinder (step F).
Repeat step F until all the air in the brake fluid is bled out.
When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.
Repeat the above procedures to bleed the other brake line.
Turn the ignition switch to OFF.
Turn the ignition switch to ON.
Clear DTC (Click here).
| 22. INSPECT FLUID LEVEL IN RESERVOIR |
![]() |
Turn the ignition switch to OFF, and depress the brake pedal more than 40 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.
When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).
| 23. INSPECT FOR BRAKE FLUID LEAKAGE |
| 24. INSPECT BRAKE MASTER CYLINDER OPERATION |
Inspect the battery positive voltage.
Turn the ignition switch to OFF, and depress the brake pedal more than 20 times.
Check that the brake pedal becomes easy to depress.
If the pedal does not become easy to depress, check and replace the brake line and hydraulic brake booster.
Turn the ignition switch to ON and check the pump motor operation noise.
If the pump motor does not operate, check and replace the wire harness and pump motor .
Connect the Techstream.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select "Active Test" mode on the Techstream.
Check the master cylinder solenoid operation.

| Inspection Order (Step) | SOL Selected By Active Test | SOL To Be Activated |
| D | TRAC Solenoid (SRCF) | SMCF |
| E | TRAC Solenoid (SRCF & SRCR) | SREA and SMCF |
| F | ABS Solenoid (SFRH) | SFRH |
| G | ABS Solenoid (SFLH) | SFLH |
| H | ABS Solenoid (SFRR & SFRH) | SFRR and SFRH |
| I | ABS Solenoid (SFLR & SFLH) | SFLR and SFLH |
| J | TRAC Solenoid (SRMF) | SREC |
| K | TRAC Solenoid (SRMF & SRMR) | STR and SREC |
| L | ABS Solenoid (SRRH) | SRRH |
| M | ABS Solenoid (SRLH) | SRLH |
| N | ABS Solenoid (SRRR & SRRH) | SRRR and SRRH |
| O | ABS Solenoid (SRLR & SRLH) | SRLR and SRLH |
Inspect front VSC solenoid (SMCF) operation (step D).
Select "TRAC Solenoid (SRCF)" on the Techstream.
Turn the "TRAC Solenoid (SRCF)" on by the Techstream, then depress the brake pedal with stable force and check that the pedal cannot be depressed.
If the pedal can be depressed, replace the hydraulic brake booster.
Release the brake pedal.
When the solenoid is off, depress the brake pedal again and check that the brake pedal can be depressed.
If the pedal can be depressed, replace the hydraulic brake booster.
Prepare the vehicle.
Jack up and support the vehicle.
Release the parking brake pedal (lever).
Shift the shift lever to the "N" position and check the rear wheels by rotating them by hand.
Inspect front VSC solenoid (SREA) operation (step E).
Select "TRAC Solenoid (SRCF & SRCR)" on the Techstream.
Turn the "TRAC Solenoid (SRCF & SRCR)" on simultaneously by the Techstream, then depress the brake pedal with stable force.
When the solenoids are on, check that the front wheels do not rotate by hand.
If the front wheels rotate, replace the brake master cylinder.
When the solenoids are off, turn the "TRAC Solenoid (SRCF)" on again, then depress the brake pedal and check the front wheels by rotating them by hand.
If front wheels stop, replace the hydraulic brake booster.
When the "TRAC Solenoid (SRCF)" is off, depress the brake pedal again and check that the brake pedal can be depressed.
If the pedal can be depressed, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFRH) operation (step F).
Select "ABS Solenoid (SFRH)" on the Techstream.
Turn the "ABS Solenoid (SFRH)" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the right front wheel by rotating it by hand.
If the right front wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
If the right front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFLH) operation (step G).
Select "ABS Solenoid (SFLH)" on the Techstream.
Turn the "ABS Solenoid (SFLH)" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the left front wheel by rotating it by hand.
If the left front wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
If the left front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFRR) operation (step H).
Select "ABS Solenoid (SFRR & SFRH)" on the Techstream.
Depress the brake pedal with stable force, then turn the "ABS Solenoid (SFRR & SFRH)" on simultaneously by the Techstream.
When the solenoids are on, check the right front wheel by rotating it by hand.
If the right front wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
If the right front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFLR) operation (step I).
Select "ABS Solenoid (SFLR & SFLH)" on the Techstream.
Depress the brake pedal with stable force, then turn the "ABS Solenoid (SFLR & SFLH)" on simultaneously by the Techstream.
When the solenoids are on, check the left front wheel by rotating it by hand.
If the left front wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
If the left front wheel rotates, replace the hydraulic brake booster.
Inspect rear VSC solenoid (SREC) operation (step J).
Select "TRAC Solenoid (SRMF)" on the Techstream.
Depress the brake pedal with stable force, then turn the "TRAC Solenoid (SRMF)" on by the Techstream.
Release the brake pedal when the solenoid is on, and check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.
When the solenoid is off, check the rear wheels by rotating them by hand.
If the rear wheels stop, replace the hydraulic brake booster.
Inspect rear VSC solenoid (STR) operation (step K).
Select "TRAC Solenoid (SRMR)" on the Techstream.
Turn the "TRAC Solenoid (SRMR)" on simultaneously by the Techstream.
When the solenoids are on , check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.
When the solenoids are off, check the rear wheels by rotating them by hand.
If the rear wheels stop, replace the hydraulic brake booster.
When the "TRAC Solenoid (SRMF)" is off, depress the brake pedal again and check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRRH) operation (step L).
Select "ABS Solenoid (SRRH)" on the Techstream.
Turn the "ABS Solenoid (SRRH)" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the right rear wheel by rotating it by hand.
If the right rear wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
If the right rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRLH) operation (step M).
Select "ABS Solenoid (SRLH)" on the Techstream.
Turn the "ABS Solenoid (SRLH)" on by the Techstream, then depress the brake pedal with stable force.
When the solenoid is on, check the left rear wheel by rotating it by hand.
If the left rear wheel stops, replace the hydraulic brake booster.
When the solenoid is off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
If the left rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRRR) operation (step N).
Select "ABS Solenoid (SRRR & SRRH)" on the Techstream.
Depress the brake pedal with stable force, then turn the "ABS Solenoid (SRRR & SRRH)" on simultaneously by the Techstream.
When the solenoids are on, check the right rear wheel by rotating it by hand.
If the right rear wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
If the right rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRLR) operation (step O).
Select "ABS Solenoid (SRLR & SRLH)" on the Techstream.
Depress the brake pedal with stable force, then turn the "ABS Solenoid (SRLR & SRLH)" on simultaneously by the Techstream.
When the solenoids are on, check the left rear wheel by rotating it by hand.
If the left rear wheel stops, replace the hydraulic brake booster.
When the solenoids are off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
If the left rear wheel rotates, replace the hydraulic brake booster.
Lower the vehicle.
Disconnect the Techstream.