Home › BRAKE › BRAKE › BRAKE BOOSTER

BRAKE BOOSTER > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY


    C189746
  1. Install a new grommet onto the brake booster assembly.

  1. Install the vacuum check valve onto the brake booster assembly.



2. INSTALL BRAKE BOOSTER ASSEMBLY
  1. Install the push rod clevis.

  1. Install a new gasket onto the brake booster assembly.



    C187273
  1. Install the brake booster assembly with the 4 nuts.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }



    C187256
  1. Connect the vacuum hose to the brake booster assembly.



3. INSTALL MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.

  1. Install the push rod clevis onto the brake pedal lever with the push rod pin and clip.



4. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
  1. Install a new O-ring onto the brake master cylinder sub-assembly.



    C187255
  1. Install the brake master cylinder sub-assembly with the 2 nuts onto the brake booster.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    C187280E01
  1. Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 187 kgf*cm , 13 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 20 mm (0.787 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



    C189743
  1. Connect the brake fluid level warning switch connector to the brake master cylinder sub-assembly.



5. INSTALL CLUTCH RESERVOIR TUBE (for Manual Transmission)


    C187253
  1. Connect the clutch reservoir tube to the reservoir.



6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



7. FILL RESERVOIR WITH BRAKE FLUID


C187250

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



8. BLEED MASTER CYLINDER
Click here

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C187279
  1. Using a union nut wrench, separate the brake tubes from the master cylinder.



    C187251
  1. Slowly depress the brake pedal and hold it there (Step A).



    C187252
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C187280E01
  1. Using a union nut wrench, install the brake tubes into the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 187 kgf*cm , 13 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 20 mm (0.787 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



9. BLEED BRAKE LINE


C187268
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



10. BLEED BRAKE ACTUATOR

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with the Techstream by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the Techstream to the DLC3, and turn the ignition switch ON.

    NOTICE:
    Do not start the engine.

  1. Select "Air Bleeding" on the Techstream.

    HINT:
    Refer to the Techstream operator's manual for further details.



  1. Bleed the air out of the brake line when Step 1: Increase appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to either one of the bleeder plugs.



    2. C187268
    3. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    4. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    5. Repeat steps E and F until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug completely.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2: Inhalation appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the Techstream (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the Techstream display and tighten the bleeder plug (Step H).

    4. Repeat steps G and H until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the Techstream, operate the brake actuator assembly, completely depress the brake pedal and hold it there (Step J).

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, and then release the brake pedal (Step K).

    5. Repeat steps I to K until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.



  1. Bleed the air out of the brake line again when Step 4: Increase appears on the Techstream display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to either one of the bleeder plugs.



    2. C187268
    3. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step L).

    4. When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step M).

    5. Repeat steps L and M until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    8. Make sure that the air bleeding is complete by referring to the Techstream display and turn off the Techstream.

    9. Disconnect the Techstream from the DLC3.

    10. Turn the ignition switch off.



11. INSPECT FLUID LEVEL IN RESERVOIR


A261799
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



12. INSPECT FOR BRAKE FLUID LEAK


13. INSPECT BRAKE PEDAL HEIGHT


C187248E01
  1. Check the brake pedal height.

    Pedal height from dash panel:
    Type
    Pedal Height
    Hydraulic brake booster
    158.6 to 168.6 mm (6.25 to 6.63 in.)
    Vacuum brake booster,
    Automatic transmission
    159.8 to 169.8 mm (6.30 to 6.68 in.)
    Vacuum brake booster,
    Manual transmission
    156.6 to 166.6 mm (6.17 to 6.55 in.)

    NOTICE:
    Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

    If the pedal height is incorrect, adjust the rod operating adapter length.



    C189741E01
  1. Adjust the rod operating adapter length.

    1. Remove the clip and clevis pin.

    2. Loosen the clevis lock nut.

    3. Adjust the rod operating adapter length by turning the pedal push rod clevis.

      Rod operating adapter length A:
      for Hydraulic brake booster:
      214 to 224 mm (8.425 to 8.818 in.)
      for Vacuum brake booster:
      213 to 223 mm (8.386 to 8.780 in.)

    4. Tighten the clevis lock nut.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

    5. Install the clip and clevis pin.

      1. If the pedal height is incorrect even when the rod operating adapter is adjusted, check that there is no damage in the brake pedal, brake pedal lever, brake pedal bracket or dash panel.
      2. Even if there is damage, there is no problem if the reserve distance is within the standard value.
      3. If necessary, replace the parts.



14. INSPECT PEDAL FREE PLAY


C189744E01
  1. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.

  1. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

    Pedal free play:
    1 to 6 mm (0.04 to 0.24 in.)



15. INSPECT PEDAL RESERVE DISTANCE


R000934E10
  1. Release the parking brake pedal.
    With the engine running, depress the pedal and measure the pedal reserve distance as shown.

    Pedal reserve distance from asphalt sheet at 490 N (50 kgf, 110.2 lbf):
    More than 55 mm (2.17 in.)

    If incorrect, troubleshoot the brake system.



16. INSTALL DRIVER SIDE JUNCTION BLOCK

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



17. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. Engage the 3 clips and install the lower NO. 1 instrument panel finish panel sub-assembly.

  1. Install the 2 bolts <B>.



18. INSTALL INSTRUMENT PANEL UNDER TRAY (for Automatic Transmission)
  1. Engage the 4 clips and 2 claws, and install the instrument panel under tray.



19. INSTALL INSTRUMENT PANEL HOLE COVER (for Manual Transmission)
  1. Engage the 4 clips and install the instrument panel hole cover.



20. INSTALL COWL SIDE TRIM BOARD LH (for Regular Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



21. INSTALL COWL SIDE TRIM BOARD LH (for Access Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



22. INSTALL COWL SIDE TRIM BOARD LH (for Double Cab)
  1. Engage the 2 clips and install the cowl side trim board.

  1. Install the clip.



23. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)
  1. Engage the 8 claws and clip, and install the front door scuff plate.



24. INSTALL FRONT DOOR SCUFF PLATE LH (for Access Cab)
  1. Engage the 9 claws and clip, and install the front door scuff plate.



25. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab)
  1. Engage the 9 claws and install the front door scuff plate.



26. INSTALL FRONT FLOOR FOOTREST


    B087437E01
  1. Engage the 2 clips and install the front floor footrest.