Home › ENGINE ยท 1GR-FE › LUBRICATION › ENGINE OIL COOLER

ENGINE OIL COOLER > INSTALLATION

for Preparation Click here



1. INSTALL OIL COOLER ASSEMBLY
  1. Clean the oil cooler contact surface on the cooler mounting.

  1. Install a new O-ring onto the oil cooler.

  1. Apply a light coat of engine oil to the threads of the union bolt.



    A076454E01
  1. Install the oil cooler and plate washer with the union bolt.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

  1. Connect the 2 oil cooler hoses to the oil cooler.



2. INSTALL OIL FILTER SUB-ASSEMBLY


A076324E01
  1. Clean the oil filter contact surface on the oil filter bracket.

  1. Apply clean engine oil to the rubber gasket of a new oil filter.

  1. Tighten the oil filter by hand until the rubber gasket comes into contact with the seat of the filter bracket.



    A076325E05
  1. Using SST, tighten it an additional 3/4 turn to set the filter.
    Text in Illustration 
    *a
    3/4 Turn

    SST
    09228-07501  

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



3. ADD ENGINE COOLANT
  1. Pour coolant into the radiator until it overflows.

    Capacity:

    Transmission
    Capacity
    Manual Transmission
    9.7 liters (10.3 Us qts, 8.5 Imp. qts)
    Automatic Transmission
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Condition
      Fan Speed
      Any setting except OFF
      Temperature
      Toward WARM
      Air Conditioning Switch
      OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warming up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (a) through (h) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.



4. ADD ENGINE OIL
  1. Fill with fresh engine oil.

    Standard engine oil:

    Oil grade
    Oil viscosity (SAE)
    ILSAC multigrade engine oil
    5W-30


    Standard capacity (for 2WD):

    Item
    Specified Condition
    Drain and refill with oil filter change
    4.5 liters (4.8 US qts, 4.0 lmp. qts)
    Drain and refill without oil filter change
    4.2 liters (4.4 US qts, 3.7 lmp. qts)
    Dry fill
    5.6 liters (5.9 US qts, 4.9 lmp. qts)


    Standard capacity (for PRE RUNNER and 4WD):

    Item
    Specified Condition
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 lmp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 lmp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 lmp. qts)

  1. Reinstall the oil filler cap.



5. CHECK ENGINE OIL LEVEL


6. CHECK FOR ENGINE OIL LEAKAGE


7. CHECK FOR ENGINE COOLANT LEAKAGE
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.



8. INSTALL V-BANK COVER
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }