Home › STEERING › POWER STEERING › POWER STEERING LINK (for 2WD)

POWER STEERING LINK (for 2WD) > DISASSEMBLY

for Preparation Click here



1. REMOVE STEERING GEAR OUTLET RETURN TUBE


F051685E02
  1. Using union nut wrench, remove the return tube.



2. REMOVE STEERING TURN PRESSURE TUBE


F051693E02
  1. Using union nut wrench, remove the 2 pressure tubes.

  1. Remove the 4 O-rings from the pressure tubes.



3. FIX POWER STEERING LINK


F051694E01
  1. Using SST, fix the power steering link between aluminium plates in a vise, as shown in the illustration.

    SST
    09612-00012  

    NOTICE:
    When using a vise, do not over tighten it.



4. REMOVE TIE ROD END SUB-ASSEMBLY LH


F051695E01
  1. Place matchmarks on the tie rod end, lock nut and rack end.

  1. Loosen the lock nut and remove the tie rod end and lock nut.



5. REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



6. REMOVE STEERING RACK BOOT CLIP
  1. Remove the 2 rack boot clips.



7. REMOVE STEERING RACK BOOT NO. 1 CLAMP
  1. Using pliers, remove the rack boot No. 1 clamp.

    NOTICE:
    Be careful not to damage the steering rack boot No. 1.



8. REMOVE STEERING RACK BOOT NO. 2 CLAMP

HINT:
The removal procedure for the No. 2 side is the same as that for the No. 1 side.



9. REMOVE STEERING RACK BOOT NO. 1


10. REMOVE STEERING RACK BOOT NO. 2


11. REMOVE STEERING RACK END SUB-ASSEMBLY


F051704E01
  1. Using a screwdriver and hammer, unstake the claw washer.

    NOTICE:
    Avoid any impact to the power steering rack.



    F051737E01
  1. Using 2 SSTs, remove the 2 steering rack ends and 2 claw washers.

    SST
    09922-10010  

    NOTICE:
    1. Turn SST 09922-10010 in the direction shown in the illustration.
    2. Securely hold the steering rack end with SST.



12. REMOVE STEERING GEAR RACK GUIDE


F051738E01
  1. Using SST, remove the rack guide spring cap nut.

    SST
    09922-10010  

    NOTICE:
    Turn SST 09922-10010 in the direction shown in the illustration.



    F051739E01
  1. Using SST, remove the rack guide spring cap.

    SST
    09631-10021  

  1. Remove the rack guide spring and rack guide.



13. REMOVE POWER STEERING CONTROL VALVE ASSEMBLY


F051740E01
  1. Wind vinyl tape around the serrated portion of the control valve.

  1. Remove the dust cover from the control valve housing.



    F051709
  1. Remove the 2 bolts and control valve w/ control valve housing.

  1. Remove the O-ring from the control valve housing.



    F051710E01
  1. To prevent the oil seal lip form getting damaged, wind vinyl tape around the serrated portion of the control valve.

  1. Using a plastic hammer, remove the control valve from the control valve housing.



    F051711E01
  1. Using a screwdriver, remove the 4 control valve rings.

    NOTICE:
    Be careful not to damage the grooves for the control valve rings.



14. REMOVE POWER STEERING CONTROL VALVE UPPER OIL SEAL


F051712E01
  1. Using SST and a press, remove the control valve upper bearing and control valve upper oil seal from the control valve housing.

    SST
    09950-60010   (09951-00250)
    09950-70010   (09951-07150)



15. REMOVE CYLINDER END STOPPER


F051713E01
  1. Using a screwdriver and hammer, turn the cylinder end stopper clockwise until the wire end can be seen through the service hole.

  1. Using a screwdriver and hammer, turn the cylinder end stopper counterclockwise, and remove the wire and cylinder end stopper.



16. REMOVE POWER STEERING RACK


17. REMOVE POWER STEERING RACK BUSH
  1. Remove the rack bush from the power steering rack.

  1. Using a screwdriver, remove the O-ring from the rack bush.



    F051714E01
  1. Using SST, remove the rack bush oil seal.

    SST
    09527-21011  
    09612-24014   (09613-22011)



18. REMOVE POWER STEERING CYLINDER TUBE OIL SEAL


F051741E01
  1. Using SST and a press, remove the cylinder tube oil seal.

    SST
    09950-60010   (09951-00290)
    09950-70010   (09951-07360)



19. REMOVE RACK STEERING PISTON RING


R010955
  1. Using a screwdriver, remove the piston ring and O-ring.

    NOTICE:
    Be careful not to damage the groove for the piston ring.