Home › STEERING › POWER STEERING › POWER STEERING LINK (for 4WD and Pre-Runner)

POWER STEERING LINK (for 4WD and Pre-Runner) > INSTALLATION

for Preparation Click here



1. INSTALL POWER STEERING LINK


F051684E01
  1. Install the power steering link with the 2 bolts and 2 nuts.

    Torque:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }

    NOTICE:
    Never turn the nut since it has a detent. Be sure to turn only the bolt.



2. INSTALL PRESSURE FEED TUBE ASSEMBLY


F051683E01
  1. Connect the return hose with the clip.



    F051698E02
  1. Using union nut wrench, tighten the flare nut and connect the pressure feed tube.

    Torque:
    for use without union nut wrench:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    for use with union nut wrench:
    22 N*m{ 222 kgf*cm , 16 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when union nut wrench is parallel to a torque wrench.



    F051680E01
  1. for 2TR-FE:

    1. Install the tube support bracket with the bolt.

      Torque:
      28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    F051681E01
  1. for 1GR-FE:

    1. Install the tube support brackets with the 2 bolts.

      Torque:
      28 N*m{ 286 kgf*cm , 21 ft.*lbf }



3. INSTALL TIE ROD END SUB-ASSEMBLY LH
  1. Install the tie rod end onto the steering knuckle arm.

  1. Install the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.



4. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.



5. INSTALL STEERING INTERMEDIATE SHAFT NO. 2


F051678E02
  1. Align the matchmarks on the steering intermediate shaft No. 2 and power steering link.

  1. Install the steering intermediate shaft No. 2 onto the power steering link with bolt C.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    F051677E01
  1. Align the matchmarks on the steering intermediate shaft and steering sliding yoke.

  1. Install the steering sliding yoke onto the steering intermediate shaft and slide it upward.

  1. Align the matchmarks on the steering sliding yoke and steering intermediate shaft No. 2.

  1. Install the steering sliding yoke with bolts A and B.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



6. INSTALL FRONT STABILIZER BAR


7. INSTALL FRONT STABILIZER BRACKET NO. 1 LH


G020162
  1. Install the front stabilizer bracket with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



8. INSTALL FRONT STABILIZER BRACKET NO. 1 RH

HINT:
The installation procedure for the RH is the same as that for the LH side.



9. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


C099158
  1. Connect the stabilizer link to the steering knuckle with the nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH is the same as that for the LH side.



11. INSTALL FRAME CROSSMEMBER SUB-ASSEMBLY NO. 3


G021429
  1. Install the frame crossmember sub-assembly No. 3 with the 8 bolts and nuts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the 4 bolts onto the engine mounting insulator rear No. 1.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



12. INSTALL PROPELLER SHAFT ASSEMBLY (for Regular Cab Pre-Runner)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft assembly into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



13. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Except Regular Cab Pre-Runner)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with the 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.



    F052184E02
  1. Adjust the center support bearing.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing to keep the intervals, as shown.
    2. In the same condition, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.039 to 0.039 in.) of each other in the vehicle's longitudinal direction when the vehicle is unladen.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



14. INSTALL PROPELLER SHAFT ASSEMBLY (for Regular Cab 4WD)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C060588E01
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



15. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Except Regular Cab 4WD)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098708E02
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



16. INSTALL PROPELLER SHAFT ASSEMBLY FRONT (for 4WD)


C098708E03
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



17. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for 2TR-FE)


A077857E01
  1. Check the free length.

    1. Using vernier calipers, measure the free length of the compression spring.

      Minimum:
      40.5 mm (1.594 in.)

      If the free length is less than the minimum, replace the compression spring.



    A076194E06
  1. Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the exhaust manifold.

    NOTICE:
    1. Make sure that the gasket is in the correct angle when installing.
    2. Do not reuse the removed gasket.
    3. Never push a new gasket into the exhaust manifold by installing the exhaust pipe front into the exhaust manifold.

  1. Install the exhaust pipe front into the exhaust pipe support.

  1. Tighten the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



18. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for 1GR-FE)
  1. Install a new gasket onto the exhaust manifold RH.

  1. Install the exhaust front pipe with the new 2 nuts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }



19. INSTALL EXHAUST FRONT PIPE ASSEMBLY NO. 2 (for 1GR-FE)
  1. Install a new gasket onto the exhaust manifold LH.

  1. Install a new gasket onto the exhaust front pipe.

  1. Install the exhaust front pipe No. 2 onto the insulator.

  1. Install the exhaust front pipe No. 2 onto the exhaust manifold LH with the new 2 nuts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }

  1. Install the exhaust front pipe No. 2 onto the exhaust front pipe with the 2 bolts and 2 nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



    G036129E02
  1. Install a new gasket onto the exhaust front pipe No. 2.

    1. Using a wooden block and plastic- faced hammer, tap in a new gasket until it is flush with the exhaust front pipe No. 2.

      NOTICE:
      1. Make sure that the gasket is in the correct direction when installing.
      2. Do not reuse the removed gasket.



20. INSTALL FRONT WHEELS

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



21. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


22. INSPECT STEERING WHEEL CENTER POINT


23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

(Click here)


24. ADD POWER STEERING FLUID


25. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds. Then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds (step A).

    2. Repeat step A several times.

  1. Stop the engine.



    C114971E01
  1. Check for foaming or emulsification.
    Especially, if the system has to be bled twice because of foaming or emulsification, check for fluid leakage in the system.

  1. Check the fluid level.



26. CHECK FOR POWER STEERING FLUID LEAKAGE


27. CHECK FOR EXHAUST GAS LEAKAGE


28. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


29. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY NO. 1

Torque:
30 N*m{ 306 kgf*cm , 22 ft.*lbf }