MANUAL TRANSMISSION UNIT > REASSEMBLY |
| 1. INSTALL OUTPUT SHAFT ASSEMBLY |
![]() |
Apply gear oil to the sliding part of the output shaft assembly.
Using a plastic hammer, install the output shaft assembly by tapping the intermediate plate.
| 2. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING |
![]() |
Using a snap ring expander, install the output shaft bearing shaft snap ring to the output shaft assembly.
| 3. INSTALL INPUT SHAFT ASSEMBLY |
![]() |
Apply gear oil to the input shaft assembly and the No. 2 synchronizer ring, and install them to the output shaft assembly.
| 4. INSTALL COUNTER GEAR ASSEMBLY |
![]() |
Temporarily install the counter gear assembly to the intermediate plate.
| 5. INSTALL COUNTER SHAFT CENTER BEARING |
![]() |
Using SST and a hammer, install a new counter shaft center bearing to the intermediate plate.
![]() |
Using a snap ring expander, install the snap ring.
| 6. INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY |
![]() |
Apply gear oil to each sliding part of the reverse idler gear sub-assembly and the reverse idler gear shaft, and install them to the intermediate plate.
| 7. INSTALL OUTPUT SHAFT REAR BEARING RETAINER |
![]() |
Install the output shaft rear bearing retainer into the groove of the reverse idler gear shaft with the 4 bolts.
| 8. INSTALL 5TH GEAR THRUST WASHER PIN |
![]() |
Apply MP grease to the 5th gear thrust washer pin, and install it to the counter gear assembly.
| 9. INSTALL 5TH GEAR THRUST WASHER |
![]() |
Apply gear oil to the 5th gear thrust washer, and install it to the counter gear assembly.
| 10. INSTALL NO. 3 TRANSMISSION HUB SLEEVE |
1-piece Type Key Spring:
Apply gear oil to the sliding part of No. 3 transmission hub sleeve, and install it to the counter shaft 5th gear.
![]() |
Install the 2 No. 3 synchromesh shifting keys and the No. 3 synchromesh shifting key spring to the counter shaft 5th gear as shown in the illustration.
| *1 | No. 3 Synchromesh Shifting Key |
| *2 | No. 3 Synchromesh Shifting Key Spring |
![]() |
Using a snap ring expander, install the snap ring to the counter shaft 5th gear.
2-piece Type Key Spring:
Apply gear oil to the sliding part of No. 3 transmission hub sleeve, and install it to the counter shaft 5th gear.
![]() |
Install the 2 No. 3 synchromesh shifting keys and the 2 No. 3 synchromesh shifting key springs to the counter shaft 5th gear as shown in the illustration.
| *1 | No. 3 Synchromesh Shifting Key |
| *2 | No. 3 Synchromesh Shifting Key Spring |
![]() |
Using a snap ring expander, install the snap ring to the counter shaft 5th gear.
| 11. INSTALL COUNTER 5TH GEAR BEARING |
![]() |
Apply gear oil to the counter 5th gear bearing and install it to the counter shaft 5th gear.
| 12. INSTALL COUNTER SHAFT 5TH GEAR |
![]() |
Apply gear oil to the counter shaft 5th gear and the No. 3 transmission hub sleeve, and install them to the counter gear assembly.
| 13. INSTALL NO. 3 SYNCHRONIZER RING |
![]() |
Apply gear oil to the No. 3 synchronizer ring, and install it to the counter gear assembly.
| 14. INSTALL NO. 5 GEAR SPLINE PIECE |
![]() |
Using SST and a press, install the No. 5 gear spline piece to the counter gear assembly.
| 15. INSTALL COUNTER GEAR REAR SHAFT SNAP RING |
Select a counter gear rear shaft snap ring so that the thrust clearance between the No. 5 gear spline piece and the counter gear rear shaft snap ring is within the specified values.
| Part No. | Mark | Thickness mm (in.) |
| 90520-22016 | A | 2.85 (0.112) |
| 90520-22017 | B | 2.90 (0.114) |
| 90520-22018 | C | 2.95 (0.116) |
| 90520-22019 | D | 3.00 (0.118) |
| 90520-22020 | E | 3.05 (0.120) |
| 90520-22021 | F | 3.10 (0.122) |
| 90520-22022 | G | 3.15 (0.124) |
![]() |
Using a brass bar and hammer, install the counter gear rear shaft snap ring to the counter gear assembly.
| 16. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the thrust clearance.
| 17. INSPECT COUNTER SHAFT 5TH GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the radial clearance.
| 18. INSTALL OUTPUT SHAFT REAR BEARING |
![]() |
Using SST and a press, install the output shaft spacer and a new output shaft rear bearing to the output shaft assembly.
| 19. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING |
Select an output shaft bearing shaft snap ring so the thrust clearance between the output shaft bearing shaft snap ring and the output shaft rear bearing is within the specified values.
| Part No. | Mark | Thickness mm (in.) |
| 90520-28031 | A | 2.65 (0.104) |
| 90520-28032 | B | 2.70 (0.106) |
| 90520-28033 | C | 2.75 (0.108) |
| 90520-28034 | D | 2.80 (0.110) |
| 90520-28035 | E | 2.85 (0.112) |
| 90520-28037 | F | 2.90 (0.114) |
| 90520-28039 | G | 2.95 (0.116) |
| 90520-28042 | H | 3.00 (0.118) |
| 90520-28043 | J | 3.05 (0.120) |
| 90520-28045 | K | 3.10 (0.122) |
| 90520-28046 | L | 3.15 (0.124) |
| 90520-28047 | M | 3.20 (0.126) |
| 90520-28048 | N | 3.25 (0.128) |
| 90520-28049 | P | 3.30 (0.130) |
| 90520-28050 | Q | 3.35 (0.132) |
| 90520-28051 | R | 3.40 (0.134) |
| 90520-28052 | S | 3.45 (0.136) |
![]() |
Using a brass bar and hammer, install the output shaft bearing shaft snap ring to the output shaft assembly.
| 20. INSTALL SPEEDOMETER DRIVE GEAR |
![]() |
Using a snap ring expander, install the snap ring.
Install the ball and the speedometer drive gear.
Using a snap ring expander, install the snap ring.
| 21. INSTALL REVERSE SHIFT ARM BRACKET |
![]() |
Install the reverse shift arm bracket to the intermediate plate with the 2 bolts.
| 22. INSTALL REVERSE SHIFT FORK |
![]() |
Install the reverse shift arm to the reverse shift fork.
Using a screwdriver and a hammer, install the E-ring.
![]() |
Install the tip of the reverse shift arm to the reverse idler gear sub-assembly. Align the cut end of the reverse shift arm with the reverse shift arm bracket pin, and install them.
| 23. INSTALL NO. 4 GEAR SHIFT FORK SHAFT |
![]() |
Install the reverse shift fork return compression spring and the reverse shift fork ball to the reverse shift fork.
![]() |
Apply gear oil to the sliding part of the No. 4 gear shift fork shaft.
Using a screwdriver, install the No. 4 gear shift fork shaft by pushing the reverse shift fork ball gently.
![]() |
Using a brass bar and hammer, install the shift fork shaft snap ring to the No. 4 gear shift fork shaft.
| 24. INSTALL REVERSE SHIFT FORK SHAFT |
![]() |
Install the reverse shift fork ball to the reverse shift fork.
![]() |
Install the No. 1 shift interlock roller to the intermediate plate.
![]() |
Install the No. 3 shift fork to the No. 3 transmission hub sleeve. Then apply gear oil to the reverse shift fork shaft and install it to the intermediate plate from the front side.
![]() |
Using a brass bar and hammer, install the shift fork shaft snap ring to the reverse shift fork shaft.
![]() |
Using a pin punch (5 mm) and hammer, install the shift fork set slotted spring pin to the No. 3 shift fork.
| 25. INSTALL NO. 1 GEAR SHIFT FORK SHAFT |
![]() |
Install the No. 1 shift interlock roller to the intermediate plate.
![]() |
Install the No. 1 shift fork to the reverse gear.
![]() |
Apply gear oil to the No. 1 gear shift fork shaft and install it to the intermediate plate from the rear side.
![]() |
Install a new bolt to the No. 1 shift fork.
![]() |
Using a brass bar and hammer, install the shift fork shaft snap ring to the No. 1 gear shift fork shaft.
| 26. INSTALL NO. 2 GEAR SHIFT FORK SHAFT |
![]() |
Install the shift interlock pin and the No. 1 shift interlock roller to the intermediate plate.
![]() |
Install the No. 2 shift fork to the No. 2 transmission hub sleeve.
![]() |
Apply gear oil to the No. 2 gear shift fork shaft and install it to the intermediate plate from the rear side.
![]() |
Install a new bolt to the No. 2 shift fork.
![]() |
Using a brass bar and hammer, install the shift fork shaft snap ring to the No. 2 gear shift fork shaft.
| 27. INSTALL NO. 1 SHIFT DETENT BALL SPRING SEAT |
![]() |
Install the 2 shift detent balls and the 2 shift detent ball low side compression springs to the intermediate plate.
![]() |
Apply adhesive to 2 or 3 threads on the 2 No. 1 shift detent ball spring seats.
Using "TORX" socket wrench T40, install the 2 No. 1 shift detent ball spring seats to the intermediate plate.
![]() |
Install the shift detent ball and the shift detent ball low side compression spring to the intermediate plate.
![]() |
Apply adhesive to 2 or 3 threads on the No. 1 shift detent ball spring seat.
Using "TORX" socket wrench T40, install the No. 1 shift detent ball spring seat to the intermediate plate.
| 28. INSTALL TRANSMISSION MAGNET |
![]() |
Clean the transmission magnet and install it to the intermediate plate.
| 29. INSTALL MANUAL TRANSMISSION CASE |
![]() |
Apply seal packing to the manual transmission case as shown in the illustration.
| *1 | Seal Packing |
![]() |
Using a plastic hammer, tap the manual transmission case to attach it to the intermediate plate.
| 30. INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING |
![]() |
Using a snap ring expander, install the No. 1 counter gear front bearing snap ring to the manual transmission case.
| 31. INSTALL FRONT BEARING SHAFT SNAP RING |
![]() |
Using a snap ring expander, install the front bearing shaft snap ring to the manual transmission case.
| 32. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL |
![]() |
Using SST and a hammer, install a new transmission front bearing retainer oil seal to the front bearing retainer.
Coat the lip of the transmission front bearing retainer oil seal with MP grease.
| 33. INSTALL FRONT BEARING RETAINER |
![]() |
Apply seal packing to the front bearing retainer as shown in the illustration.
| *1 | Seal Packing |
![]() |
Apply adhesive to 2 or 3 threads on the end of the 8 bolts.
Install the front bearing retainer to the manual transmission case with the 8 bolts.
Check that the input shaft assembly and the output shaft assembly rotate smoothly.
| 34. INSTALL MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL |
![]() |
Using SST and a hammer, install a new manual transmission extension housing oil seal to the extension housing sub-assembly.
Coat the lip of the manual transmission extension housing oil seal with MP grease.
| 35. INSTALL REVERSE RESTRICT PIN |
![]() |
Install the reverse restrict pin to the extension housing sub-assembly.
![]() |
Using a pin punch (5 mm) and hammer, install the reverse restrict slotted pin to the extension housing sub-assembly.
Apply adhesive to 2 or 3 threads on the 2 plugs.
Using "TORX" socket wrench T40, install the 2 plugs to the extension housing sub-assembly.
| 36. INSTALL EXTENSION HOUSING OIL RECEIVER PIPE |
Install the extension housing oil receiver pipe to the extension housing sub-assembly with the bolt.
| 37. INSTALL OIL RECEIVER PIPE |
![]() |
Install the oil receiver pipe to the extension housing sub-assembly.
| 38. INSTALL EXTENSION HOUSING SUB-ASSEMBLY |
![]() |
Apply seal packing to the extension housing sub-assembly as shown in the illustration.
| *1 | Seal Packing |
Insert the shift and select lever to the extension housing sub-assembly.
![]() |
Connect the shift and select lever to the shift fork shaft and put in the shift lever housing.
Align the shift and select lever to the extension housing installation hole and push in the extension housing sub-assembly.
![]() |
Install the extension housing sub-assembly to the manual transmission case with the 10 bolts.
![]() |
Apply adhesive to 2 or 3 threads on the end of the bolt.
Install the bolt to the shift lever housing.
| 39. INSTALL REVERSE RESTRICT PIN ASSEMBLY |
![]() |
Install the 2 reverse restrict pin assemblies to the extension housing sub-assembly.
| *a | Identification Paint Color: White |
| *b | Identification Paint Color: Green |
| 40. INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY |
![]() |
Install a new control shift lever retainer gasket and the floor shift control shift lever retainer sub-assembly to the extension housing sub-assembly with the 6 bolts.
| 41. INSTALL SPEEDOMETER DRIVEN GEAR SUB-ASSEMBLY |
Install a new O-ring to the speedometer driven gear sub-assembly.
Install the speedometer driven gear sub-assembly to the extension housing sub-assembly with the bolt.
| 42. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY |
![]() |
Using SST, install a new gasket and the back-up light switch assembly to the manual transmission case.
| 43. INSTALL CLUTCH HOUSING |
![]() |
Install the clutch housing to the manual transmission case with the 9 bolts.
| 44. INSTALL CLUTCH RELEASE FORK BOOT |
| 45. INSTALL RELEASE FORK SUPPORT |
Install the release fork support onto the transaxle assembly.
| 46. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY |
![]() |
Apply release hub grease to the release fork and release bearing assembly contact surfaces, release fork and push rod contact surface and release fork pivot point.
| *1 | Release hub grease |
Install the release fork onto the release bearing assembly.
| 47. INSTALL CLUTCH RELEASE BEARING ASSEMBLY |
Apply clutch spline grease to the input shaft spline.
Install the bearing onto the release fork, and then install them onto the transaxle assembly.
| 48. INSTALL DRAIN PLUG |
![]() |
Install a new gasket and the drain plug to the manual transmission case.
| 49. INSTALL FILLER PLUG |
![]() |
Install a new gasket and the filler plug to the manual transmission case.