Home › TRANSMISSION ยท R155F MANUAL TRANSMISSION › MANUAL TRANSMISSION UNIT

MANUAL TRANSMISSION UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL OUTPUT SHAFT ASSEMBLY


D029112E01
  1. Apply gear oil to the sliding part of the output shaft assembly.

  1. Using a plastic hammer, install the output shaft assembly by tapping the intermediate plate.



2. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING


D029064E01
  1. Using a snap ring expander, install the output shaft bearing shaft snap ring to the output shaft assembly.



3. INSTALL INPUT SHAFT ASSEMBLY


D026006E01
  1. Apply gear oil to the input shaft assembly and the No. 2 synchronizer ring, and install them to the output shaft assembly.

    NOTICE:
    1. Install the No. 2 synchronizer ring so that its groove fits into the No. 2 synchromesh shifting key.
    2. Check that the input shaft assembly rotates smoothly.



4. INSTALL COUNTER GEAR ASSEMBLY


D026005E01
  1. Temporarily install the counter gear assembly to the intermediate plate.



5. INSTALL COUNTER SHAFT CENTER BEARING


D029113E01
  1. Using SST and a hammer, install a new counter shaft center bearing to the intermediate plate.

    SST
    09316-60011   (09316-00011)

    HINT:
    Install the bearing while tapping the tip of the counter gear assembly so that the counter gear assembly is not pushed forward into the side wall of the output shaft gear.



    D029260E01
  1. Using a snap ring expander, install the snap ring.



6. INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY


D026002E07
  1. Apply gear oil to each sliding part of the reverse idler gear sub-assembly and the reverse idler gear shaft, and install them to the intermediate plate.

    NOTICE:
    Orient the groove side of the reverse idler gear shaft to the rear side and install it from the rear side.



7. INSTALL OUTPUT SHAFT REAR BEARING RETAINER


D026001E01
  1. Install the output shaft rear bearing retainer into the groove of the reverse idler gear shaft with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



8. INSTALL 5TH GEAR THRUST WASHER PIN


D026000E01
  1. Apply MP grease to the 5th gear thrust washer pin, and install it to the counter gear assembly.



9. INSTALL 5TH GEAR THRUST WASHER


D025999E01
  1. Apply gear oil to the 5th gear thrust washer, and install it to the counter gear assembly.

    NOTICE:
    Install the thrust washer so that its chamfer side faces to the front side.



10. INSTALL NO. 3 TRANSMISSION HUB SLEEVE


  1. 1-piece Type Key Spring:

    1. Apply gear oil to the sliding part of No. 3 transmission hub sleeve, and install it to the counter shaft 5th gear.

      NOTICE:
      Make sure that the No. 3 transmission hub sleeve and counter shaft 5th gear are oriented in the correct direction.



    2. C247404E01
    3. Install the 2 No. 3 synchromesh shifting keys and the No. 3 synchromesh shifting key spring to the counter shaft 5th gear as shown in the illustration.
      Text in Illustration 
      *1
      No. 3 Synchromesh Shifting Key
      *2
      No. 3 Synchromesh Shifting Key Spring



    4. C247403
    5. Using a snap ring expander, install the snap ring to the counter shaft 5th gear.



  1. 2-piece Type Key Spring:

    1. Apply gear oil to the sliding part of No. 3 transmission hub sleeve, and install it to the counter shaft 5th gear.

      NOTICE:
      Make sure that the No. 3 transmission hub sleeve and counter shaft 5th gear are oriented in the correct direction.



    2. C247406E01
    3. Install the 2 No. 3 synchromesh shifting keys and the 2 No. 3 synchromesh shifting key springs to the counter shaft 5th gear as shown in the illustration.
      Text in Illustration 
      *1
      No. 3 Synchromesh Shifting Key
      *2
      No. 3 Synchromesh Shifting Key Spring



    4. C247405
    5. Using a snap ring expander, install the snap ring to the counter shaft 5th gear.



11. INSTALL COUNTER 5TH GEAR BEARING


D026020E01
  1. Apply gear oil to the counter 5th gear bearing and install it to the counter shaft 5th gear.



12. INSTALL COUNTER SHAFT 5TH GEAR


D025996E01
  1. Apply gear oil to the counter shaft 5th gear and the No. 3 transmission hub sleeve, and install them to the counter gear assembly.



13. INSTALL NO. 3 SYNCHRONIZER RING


D029060E01
  1. Apply gear oil to the No. 3 synchronizer ring, and install it to the counter gear assembly.

    NOTICE:
    Install the No. 3 synchronizer ring so that its groove fits into the No. 3 synchromesh shifting key.



14. INSTALL NO. 5 GEAR SPLINE PIECE


D026022E01
  1. Using SST and a press, install the No. 5 gear spline piece to the counter gear assembly.

    SST
    09316-60011   (09316-00011)

    NOTICE:
    Check that the gear rotates smoothly.



15. INSTALL COUNTER GEAR REAR SHAFT SNAP RING
  1. Select a counter gear rear shaft snap ring so that the thrust clearance between the No. 5 gear spline piece and the counter gear rear shaft snap ring is within the specified values.

    Standard clearance:
    0.10 mm (0.00393 in.) or less

    Counter Gear Rear Shaft Snap Ring Thickness:
    Part No.
    Mark
    Thickness
    mm (in.)
    90520-22016
    A
    2.85 (0.112)
    90520-22017
    B
    2.90 (0.114)
    90520-22018
    C
    2.95 (0.116)
    90520-22019
    D
    3.00 (0.118)
    90520-22020
    E
    3.05 (0.120)
    90520-22021
    F
    3.10 (0.122)
    90520-22022
    G
    3.15 (0.124)



    D026023E01
  1. Using a brass bar and hammer, install the counter gear rear shaft snap ring to the counter gear assembly.



16. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE


D025991E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.00394 to 0.0137 in.)

    If the clearance is not as specified, replace the counter shaft 5th gear.



17. INSPECT COUNTER SHAFT 5TH GEAR RADIAL CLEARANCE


D025992E01
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    If the clearance is not as specified, replace the counter 5th gear bearing with a new one.



18. INSTALL OUTPUT SHAFT REAR BEARING


D026024E01
  1. Using SST and a press, install the output shaft spacer and a new output shaft rear bearing to the output shaft assembly.

    SST
    09309-35010  



19. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING
  1. Select an output shaft bearing shaft snap ring so the thrust clearance between the output shaft bearing shaft snap ring and the output shaft rear bearing is within the specified values.

    Standard clearance:
    0.10 mm (0.00393 in.) or less

    Output Shaft Bearing Shaft Snap Ring Thickness:
    Part No.
    Mark
    Thickness
    mm (in.)
    90520-28031
    A
    2.65 (0.104)
    90520-28032
    B
    2.70 (0.106)
    90520-28033
    C
    2.75 (0.108)
    90520-28034
    D
    2.80 (0.110)
    90520-28035
    E
    2.85 (0.112)
    90520-28037
    F
    2.90 (0.114)
    90520-28039
    G
    2.95 (0.116)
    90520-28042
    H
    3.00 (0.118)
    90520-28043
    J
    3.05 (0.120)
    90520-28045
    K
    3.10 (0.122)
    90520-28046
    L
    3.15 (0.124)
    90520-28047
    M
    3.20 (0.126)
    90520-28048
    N
    3.25 (0.128)
    90520-28049
    P
    3.30 (0.130)
    90520-28050
    Q
    3.35 (0.132)
    90520-28051
    R
    3.40 (0.134)
    90520-28052
    S
    3.45 (0.136)



    D025988E01
  1. Using a brass bar and hammer, install the output shaft bearing shaft snap ring to the output shaft assembly.



20. INSTALL REVERSE SHIFT ARM BRACKET


D025985E01
  1. Install the reverse shift arm bracket to the intermediate plate with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



21. INSTALL REVERSE SHIFT FORK


D026025E01
  1. Install the reverse shift arm to the reverse shift fork.

  1. Using a screwdriver and a hammer, install the E-ring.



    D026026E01
  1. Install the tip of the reverse shift arm to the reverse idler gear sub-assembly. Align the cut end of the reverse shift arm with the reverse shift arm bracket pin, and install them.



22. INSTALL NO. 4 GEAR SHIFT FORK SHAFT


D026027E01
  1. Install the reverse shift fork return compression spring and the reverse shift fork ball to the reverse shift fork.



    D025981E02
  1. Apply gear oil to the sliding part of the No. 4 gear shift fork shaft.

  1. Using a screwdriver, install the No. 4 gear shift fork shaft by pushing the reverse shift fork ball gently.



    D026028E01
  1. Using a brass bar and hammer, install the shift fork shaft snap ring to the No. 4 gear shift fork shaft.



23. INSTALL REVERSE SHIFT FORK SHAFT


D025979E01
  1. Install the reverse shift fork ball to the reverse shift fork.



    D025975E01
  1. Install the No. 1 shift interlock roller to the intermediate plate.



    D029058E01
  1. Install the No. 3 shift fork to the No. 3 transmission hub sleeve. Then apply gear oil to the reverse shift fork shaft and install it to the intermediate plate from the front side.



    D029114E01
  1. Using a brass bar and hammer, install the shift fork shaft snap ring to the reverse shift fork shaft.



    D029056E01
  1. Using a pin punch (5 mm) and hammer, install the shift fork set slotted spring pin to the No. 3 shift fork.



24. INSTALL NO. 1 GEAR SHIFT FORK SHAFT


D025975E01
  1. Install the No. 1 shift interlock roller to the intermediate plate.



    D029055E01
  1. Install the No. 1 shift fork to the reverse gear.



    D029054E01
  1. Apply gear oil to the No. 1 gear shift fork shaft and install it to the intermediate plate from the rear side.



    D029053E01
  1. Install a new bolt to the No. 1 shift fork.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



    D029115E01
  1. Using a brass bar and hammer, install the shift fork shaft snap ring to the No. 1 gear shift fork shaft.



25. INSTALL NO. 2 GEAR SHIFT FORK SHAFT


D025967E01
  1. Install the shift interlock pin and the No. 1 shift interlock roller to the intermediate plate.



    D029051E01
  1. Install the No. 2 shift fork to the No. 2 transmission hub sleeve.



    D029050E01
  1. Apply gear oil to the No. 2 gear shift fork shaft and install it to the intermediate plate from the rear side.



    D029049E01
  1. Install a new bolt to the No. 2 shift fork.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



    D029116E01
  1. Using a brass bar and hammer, install the shift fork shaft snap ring to the No. 2 gear shift fork shaft.



26. INSTALL NO. 1 SHIFT DETENT BALL SPRING SEAT


D033570E01
  1. Install the 2 shift detent balls and the 2 shift detent ball low side compression springs to the intermediate plate.



    D033569E05
  1. Apply adhesive to 2 or 3 threads on the 2 No. 1 shift detent ball spring seats.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using "TORX" socket wrench T40, install the 2 No. 1 shift detent ball spring seats to the intermediate plate.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



    D025960E01
  1. Install the shift detent ball and the shift detent ball low side compression spring to the intermediate plate.



    D029046E03
  1. Apply adhesive to 2 or 3 threads on the No. 1 shift detent ball spring seat.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using "TORX" socket wrench T40, install the No. 1 shift detent ball spring seat to the intermediate plate.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



27. INSTALL TRANSMISSION MAGNET


D025957E01
  1. Clean the transmission magnet and install it to the intermediate plate.



28. INSTALL MANUAL TRANSMISSION CASE


    D026033E01
  1. Apply seal packing to the manual transmission case as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



    D029117E01
  1. Using a plastic hammer, tap the manual transmission case to attach it to the intermediate plate.



29. INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING


D025954E01
  1. Using a snap ring expander, install the No. 1 counter gear front bearing snap ring to the manual transmission case.



30. INSTALL FRONT BEARING SHAFT SNAP RING


D025953E01
  1. Using a snap ring expander, install the front bearing shaft snap ring to the manual transmission case.



31. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL


D026035E06
  1. Using SST and a hammer, install a new transmission front bearing retainer oil seal to the front bearing retainer.

    SST
    09950-60010   (09951-00300, 09951-00520, 09952-06010)
    09950-70010   (09951-07100)

    Drive in depth:
    11.2 to 12.2 mm (0.441 to 0.480 in.)

  1. Coat the lip of the transmission front bearing retainer oil seal with MP grease.



32. INSTALL FRONT BEARING RETAINER


    D026036E03
  1. Apply seal packing to the front bearing retainer as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



    D025950E01
  1. Apply adhesive to 2 or 3 threads on the end of the 8 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the front bearing retainer to the manual transmission case with the 8 bolts.

    Torque:
    17 N*m{ 168 kgf*cm , 12 ft.*lbf }

  1. Check that the input shaft assembly and the output shaft assembly rotate smoothly.



33. INSTALL TRANSFER ADAPTER OIL SEAL


D029118E01
  1. Using SST and a hammer, install a new transfer adapter oil seal to the transfer adapter.

    SST
    09710-30050  
    09950-70010   (09951-07100)

    Drive in depth:
    45.4 to 46.4 mm (1.788 to 1.826 in.)

    NOTICE:
    Be careful not to damage the oil seal lip.

  1. Coat the lip of the transfer adapter oil seal with MP grease.



34. INSTALL REVERSE RESTRICT PIN


D029042E01
  1. Install the reverse restrict pin to the transfer adapter.



    F050672E01
  1. Using a pin punch (5 mm) and hammer, install the reverse restrict slotted pin to the transfer adapter.

  1. Apply adhesive to 2 or 3 threads on the plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using "TORX" socket wrench T40, install the plug to the transfer adapter.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }



35. INSTALL OIL RECEIVER PIPE


D029037E01
  1. Install the oil receiver pipe to the transfer adapter.



36. INSTALL TRANSFER ADAPTER


    D029067E13
  1. Apply seal packing to the transfer adapter as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. Insert the shift and select lever to the transfer adapter.



    G034242E01
  1. Connect the shift and select lever to the shift fork shaft and put in the shift lever housing.

  1. Align the shift and select lever to the transfer adapter installation hole and push in the transfer adapter.



    D029033E03
  1. Install the transfer adapter to the manual transmission case with the 10 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    F050674E01
  1. Apply adhesive to 2 or 3 threads on the end of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the bolt to the shift lever housing.

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }



37. INSTALL REVERSE RESTRICT PIN ASSEMBLY


    C247409E01
  1. Install the 2 reverse restrict pin assemblies to the transfer adapter.
    Text in Illustration 
    *a
    Identification Paint Color: Green
    *b
    Identification Paint Color: White
    V100135
    Front Side

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



38. INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY


F050653E01
  1. Install a new oil deflector and the floor shift control shift lever retainer sub-assembly to the transfer adapter with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



39. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY


D029030E01
  1. Using SST, install a new gasket and the back-up light switch assembly to the manual transmission case.

    SST
    09817-16011  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



40. INSTALL CLUTCH HOUSING


D029028E01
  1. Install the clutch housing to the manual transmission case with the 9 bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



41. INSTALL CLUTCH RELEASE FORK BOOT


42. INSTALL RELEASE FORK SUPPORT
  1. Install the release fork support onto the transaxle assembly.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



43. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY


    D027398E06
  1. Apply release hub grease to the release fork and release bearing assembly contact surfaces, release fork and push rod contact surface and release fork pivot point.
    Text in Illustration 
    *1
    Release hub grease

    Grease:
    Toyota Genuine Release Hub Grease or equivalent

  1. Install the release fork onto the release bearing assembly.



44. INSTALL CLUTCH RELEASE BEARING ASSEMBLY
  1. Apply clutch spline grease to the input shaft spline.

    Grease:
    Toyota Genuine Clutch Spline Grease or equivalent

  1. Install the bearing onto the release fork, and then install them onto the transaxle assembly.

    NOTICE:
    After installation, move the fork forward and backward to check that the release bearing slides smoothly.



45. INSTALL DRAIN PLUG


D029024E01
  1. Install a new gasket and the drain plug to the manual transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



46. INSTALL FILLER PLUG


D029023E01
  1. Install a new gasket and the filler plug to the manual transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }