Home › TRANSMISSION ยท R155F MANUAL TRANSMISSION › TRANSFER ADAPTER OIL SEAL

TRANSFER ADAPTER OIL SEAL > REMOVAL

for Preparation Click here



1. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Separate Seat Type)


    B085770E01
  1. Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.



2. REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Seat Type)


    B290398
  1. Remove the console box carpet.



    B290399
  1. Remove the 2 screws <F> and 2 bolts <B>.

  1. Disengage the 4 claws and remove the rear console box assembly.



3. REMOVE FRONT CONSOLE BOX (for Separate Seat Type)


    E232345
  1. Remove the shift knob.

  1. Remove the 2 screws <F>.

  1. Disengage the 2 clips and claw, and remove the front console box.



4. REMOVE FRONT CONSOLE BOX (for Bench Seat Type)


    B290403
  1. Remove the shift knob.

  1. Remove the box bottom mat.

  1. Remove the 2 instrument panel cup holders.



    E232347
  1. Remove the clip and 2 bolts <A>.

  1. Disengage the 2 clips and claw, and remove the front console box.



5. REMOVE SHIFT LEVER BOOT ASSEMBLY


F050667E01
  1. Remove the 2 screws A, 2 clips B and floor shift lever assembly.



6. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY


G021695E04
  1. Cover the shift lever cap with a cloth.

  1. While pressing down on the shift lever cap, turn it counterclockwise to remove.

  1. Pull out the shift lever.



7. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and engine under cover No. 2.



8. DRAIN MANUAL TRANSMISSION OIL

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }



9. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the exhaust pipe front from the exhaust pipe support.

  1. Remove the gasket from the exhaust manifold.



10. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


11. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Access Cab)


12. REMOVE PROPELLER SHAFT ASSEMBLY (for Regular Cab)


13. REMOVE MANIFOLD STAY


F050668
  1. Remove the 3 bolts and manifold stay.



14. REMOVE STARTER ASSEMBLY


G037949E01
  1. Remove the terminal cap.

  1. Remove the nut, then remove the starter wire harness.

  1. Disconnect the starter connector.



    G037950E01
  1. Remove the 2 bolts, then remove the starter.



15. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY


G021426
  1. Remove the 2 bolts and separate the clutch release cylinder assembly.



16. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


F050666
  1. Support the transfer with a support stand.



    G021429
  1. Remove the 4 bolts from the engine rear mounting.

  1. Remove the 4 bolts, nuts and frame crossmember sub- assembly No. 3.



17. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR


G021430
  1. Remove the 4 bolts and engine mounting insulator rear No. 1.

  1. Using a transmission jack, support the transmission unit assembly.

  1. Remove the support stand from the rear side of the transfer.



18. DISCONNECT WIRE HARNESS
  1. Tilt the transmission assembly downward.

    NOTICE:
    Make sure that the cooling fan does not come in contact with the fan shroud.

  1. Disconnect the back-up lamp switch connector.

  1. Disconnect the speed sensor connector.

  1. Disconnect the 2 transfer indicator switch connectors.

  1. Disconnect the transfer shift actuator motor connector.

  1. Disconnect the wire harness clamp from the transmission w/ transfer assembly.



19. REMOVE MANUAL TRANSMISSION WITH TRANSFER


F050669
  1. Remove the 7 bolts and remove the transmission assembly.



20. REMOVE TRANSFER ASSEMBLY


F050671
  1. Remove the 8 transfer adaptor rear mounting bolts.

  1. Pull the transfer straight up and remove it from the transmission.

    NOTICE:
    Take care not to damage the adaptor rear oil seal with the transfer input gear spline.



21. REMOVE TRANSFER ADAPTER OIL SEAL


G021435E01
  1. Using SST, remove the transfer adapter oil seal.

    SST
    09308-00010  

    NOTICE:
    Do not damage the oil seal fitted surface of the transfer adapter.