MANUAL TRANSMISSION ASSEMBLY > INSTALLATION |
| 1. INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY |
![]() |
Install the manual transmission case cover with the 5 bolts.
| 2. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY |
![]() |
Install the manual transmission with the 9 bolts.
| 3. CONNECT WIRE HARNESS |
| 4. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR |
![]() |
Install the engine mounting insulator rear No. 1 with the 4 bolts.
| 5. INSTALL NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Install the frame crossmember sub-assembly No. 3 with the 4 bolts and 4 nuts.
Install the frame crossmember sub-assembly No. 3 with the 4 bolts.
| 6. INSTALL CLUTCH ACCUMULATOR ASSEMBLY |
![]() |
Using union nut wrench, connect the 2 flexible hose tubes to the clutch accumulator.
![]() |
Install the clutch accumulator with the 3 bolts.
![]() |
Using union nut wrench, tighten the 2 flexible hose tubes.
| 7. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY |
![]() |
Install the clutch release cylinder with the 2 bolts.
| 8. INSTALL NO. 1 CLUTCH HOUSING COVER |
![]() |
Install the clutch housing cover No. 1 with the 3 bolts.
| 9. INSTALL STARTER ASSEMBLY |
Install the starter assembly with the 2 bolts.
Install the wire harness with the nut to terminal 30.
Connect terminal 50 to the starter assembly.
| 10. INSTALL MANIFOLD STAY |
![]() |
Install the manifold stay with the 3 bolts.
| 11. INSTALL NO. 2 MANIFOLD STAY |
![]() |
Install the manifold stay No. 2 with the 3 bolts.
| 12. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
![]() |
Remove SST from the extension housing.
Install the propeller shaft into the extension housing.
![]() |
Align the matchmarks on the propeller shaft flange and differential flange.
Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.
![]() |
Provisionally install the center support bearing with the 2 mounting bolts.
![]() |
Adjust the center support bearing.
Torque the 2 bolts.
| 13. INSTALL EXHAUST PIPE |
Install a new gasket onto the exhaust manifold RH.
Install the exhaust front pipe with the new 2 nuts.
| 14. ADD MANUAL TRANSMISSION OIL |
| 15. ADJUST MANUAL TRANSMISSION OIL |
![]() |
Park the vehicle in a level place.
Remove the transmission filler plug and gasket.
Check that the oil surface is within 5 mm (0.20 in.) of the lowest point of the transmission filler plug opening.
Check for oil leakage when the oil level is low.
Install the transmission filler plug and a new gasket.
| 16. INSTALL NO.2 ENGINE UNDER COVER |
| 17. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY |
![]() |
Apply MP grease to the tip of the shift lever.
![]() |
Cover the shift lever cap with a cloth.
Pressing down on the shift lever cap, turn it clockwise to install the shift lever.
| 18. INSTALL SHIFT LEVER BOOT ASSEMBLY |
Install the shift lever boot with the 2 screws and 2 clips.
| 19. INSTALL FRONT CONSOLE BOX |
![]() |
Engage the 2 clips and claw, and install the front console box.
Install the 2 screws <F>.
Install the shift knob.
| 20. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
| 21. INSTALL REAR CONSOLE BOX ASSEMBLY |
![]() |
Engage the 4 claws and install the console box rear.
Install the 2 screws <F> and 2 bolts <B>.
Install the console box carpet.
| 22. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY |
Engage the 4 clips and claw, and install the console upper panel sub-assembly.
| 23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |