Home › TRANSMISSION ยท RA60 MANUAL TRANSMISSION › MANUAL TRANSMISSION UNIT

MANUAL TRANSMISSION UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL 1ST AND REVERSE SHIFT ARM


D033725E01
  1. Install the shift arm and shift arm pivot onto the interlock bracket.



    D033724E01
  1. Install a new E-ring onto the shift arm pivot.



2. INSTALL NO. 4 GEAR SHIFT FORK SHAFT


D033723E01
  1. Install the spring and ball onto the interlock bracket.

  1. Install the shift fork shaft No. 4.



3. INSTALL NO. 4 GEAR SHIFT FORK


D033773E01
  1. Install the shift fork No. 4 onto the shift fork shaft No. 4.

  1. Using a pin punch (5 mm (0.20 in.)) and hammer, tap the new slotted pin into the shaft fork No. 4 and shift fork shaft No. 4.

    Drive in depth:
    0 to 0.5 mm (0 to 0.050 in.)



4. INSTALL NO. 1 GEAR SHIFT FORK


D033771E01
  1. Install the shift fork No. 1 and shift head No. 2 onto the shift fork shaft No. 4.

  1. Using a pin punch (5 mm (0.20 in.)) and hammer, tap the new slotted pin into the shaft head No. 2 and shift fork shaft No. 4.

    Drive in depth:
    0 to 0.5 mm (0 to 0.050 in.)



5. INSTALL NO. 1 GEAR SHIFT FORK SHAFT


F051831E01
  1. Apply MP grease to the interlock pin No. 1 and install it onto the interlock bracket.

  1. Install the spring and ball onto the interlock bracket.

  1. Install the shift fork shaft No. 1 onto the interlock bracket.

    HINT:
    Place the shift fork shaft No. 4 in the neutral position.



6. INSTALL NO. 1 GEAR SHIFT HEAD


D033772E01
  1. Install the shift head No. 1 into the shift fork shaft No. 1.

  1. Using a pin punch (5 mm (0.20 in.)) and hammer, tap the new slotted pin into the shaft head No. 1 and shift fork shaft No. 1.

    Drive in depth:
    0 to 0.5 mm (0 to 0.050 in.)



7. INSTALL NO. 2 GEAR SHIFT FORK SHAFT


F051830E01
  1. Apply MP grease to the interlock pins No. 2 and No. 3, then install them onto the interlock bracket.

  1. Install the spring and ball the interlock bracket.

  1. Install the shift fork shaft No. 2 onto the interlock bracket.

    HINT:
    Place the shift fork shafts No. 3 and No. 4 in the neutral position.



8. INSTALL NO. 2 GEAR SHIFT FORK


F051589E01
  1. Install the shift fork No. 2 with the bolt.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



9. INSTALL NO. 3 GEAR SHIFT FORK SHAFT


F051829E01
  1. Apply MP grease to the interlock pins No. 2 and No. 3, then install them onto the interlock bracket.

  1. Install the spring and ball onto the interlock bracket.

  1. Install the shift fork shaft No. 3 onto the interlock bracket.

    HINT:
    Place the shift fork shafts No. 2, No. 1 and No. 4 in the neutral position.



10. INSTALL NO. 3 GEAR SHIFT FORK


F051588E01
  1. Install the shift fork No. 3 with the bolt.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



11. INSTALL TRANSMISSION CASE OIL SEAL


D033643E01
  1. Using SST and a hammer, tap a new oil seal into the front case in accordance with the dimension specified in the illustration.

    SST
    09950-70010   (09951-07100)
    09950-60010   (09951-00470)

    Dimension A:
    60.0 to 60.8 mm (2.362 to 2.394 in.)

  1. Apply gear oil to the lip of the oil seal.



12. INSTALL FRONT BEARING SHAFT SNAP RING


D033639E01
  1. Using a snap ring plier, install the 2 snap rings.



13. INSTALL NO. 1 OIL RECEIVER PIPE


D033642E01
  1. Install the oil receiver pipe No. 1 onto the transmission front case.

    HINT:
    Align the convex portion of the oil receiver pipe with the cutout of the front case and install the oil receiver pipe onto the clutch housing.



14. INSTALL TRANSMISSION FRONT CASE


D033644E01
  1. Apply gear oil to all sliding and rotating parts.

  1. Provisionally install the output shaft, input shaft, counter gear shaft and control assembly, and tie them with a rope or string.



    D033637E01
  1. Using a snap ring expander, extend the 2 snap rings and install the output shaft, input shaft, counter gear shaft and control assembly.

    HINT:
    Make sure that the snap ring is fitted into the grooves of the input shaft and front bearing of the counter gear shaft.

  1. Untie the output shaft, input shaft, counter gear shaft and control assembly.



    F051583E01
  1. Using a hexagonal wrench (27 mm), install the plug onto the front case.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



    D033635E01
  1. Install the 4 bolts onto the interlock bracket.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



15. INSTALL REVERSE IDLER GEAR


C116297E01
  1. Install the reverse idler gear, reverse idler gear bearing and reverse idler gear shaft.

    HINT:
    Make sure that the reverse idler gear faces the correct direction as shown in the illustration.

    NOTICE:
    Make sure that the tapped hole portion of the reverse idler shaft is in the position shown in the illustration.



16. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY


F051581E01
  1. Using SST, install the back-up light switch with a new gasket onto the transmission front case.

    SST
    09817-16011  

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }



17. INSTALL SHIFT AND SELECT LEVER CAM


F051580E01
  1. Install the shift and select lever cam onto the shaft and install a new E-ring.



18. INSTALL SHIFT AND SELECT LEVER


F051579E01
  1. Install the lock ball pin and spring onto the shift and select lever.

  1. Install the shift and select lever onto the shift and select lever cam and shaft.

  1. Install the bolt onto the shift and select lever.

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }



19. INSTALL SHIFT AND SELECT LEVER SHAFT


D033647E01
  1. Align the groove of the shift and select cam with the reverse idler shaft, and the claw with the groove of the control assembly, and install them.



20. INSTALL NO. 2 OIL RECEIVER PIPE


F051577E01
  1. Install the oil receiver pipe No. 2 into the transmission middle case.



21. INSTALL DRAIN PLUG SUB-ASSEMBLY


F051576E01
  1. Install the drain plug with a new gasket onto the transmission middle case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



22. INSTALL TRANSMISSION MIDDLE CASE


    D033756E05
  1. Apply seal packing to the transmission middle case, as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Parts must be assembled within 10 minutes of application. Otherwise, the packing material must be removed and reapplied.



    D033740E02
  1. Install the transmission middle case with the 11 bolts onto the transmission front case.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Bolt length:
    Bolt A:
    40 mm (1.57 in.)
    Bolt B:
    80 mm (3.15 in.)



23. INSTALL REVERSE IDLER GEAR SHAFT BOLT


D033649E01
  1. Install a new gasket and the reverse idler gear shaft bolt onto the reverse idler gear shaft.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



24. INSTALL TRANSMISSION OIL SEPARATOR


F051575E01
  1. Install the transmission oil separator with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



25. INSTALL COUNTER GEAR REAR RADIAL BALL BEARING


D033750E01
  1. Coat a new counter gear rear radial ball bearing with gear oil, and using SST and a press, install it into the transmission rear case.

    SST
    09950-70010   (09951-07360)
    09950-60010   (09951-00650)



    D033746E01
  1. Install the bearing lock plate with the bolt.

    Torque:
    11 N*m{ 115 kgf*cm , 8.3 ft.*lbf }



26. INSTALL OUTPUT SHAFT REAR BEARING OUTER RACE


D033749E01
  1. Using SST and a press, press in 2 new bearing outer races.

    SST
    09950-70010   (09951-07100, 09951-07360)
    09950-60020   (09951-00790)



27. INSTALL OIL SEPARATOR PACKING SEAL


D033752E01
  1. Install the oil separator packing seal onto the transmission rear case.

    HINT:
    Insert the protruding part of the oil separator packing seal into the groove on the transmission rear case.



28. INSTALL EXTENSION HOUSING OIL RECEIVER PIPE


F051573E01
  1. Install the extension housing oil receiver pipe onto the transmission rear case.



29. INSTALL MANUAL TRANSMISSION FILLER PLUG


F051572E01
  1. Install the 2 transmission filler plugs with 2 new gaskets onto the transmission rear case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



30. INSTALL TRANSMISSION REAR CASE


    D033757E05
  1. Apply seal packing to the transmission rear case, as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Parts must be assembled within 10 minutes of application. Otherwise, the packing material must be removed and reapplied.



    D033738E03
  1. Install the transmission rear case with the 10 bolts and 3 brackets onto the transmission middle case.
    Text in Illustration 
    *1
    Clamp

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



31. INSTALL SHIFT DETENT BALL PLUG


F051570E01
  1. Install the ball and compression spring onto the transmission rear case.

  1. Install a new shift detent ball plug, and install it onto the transmission rear case.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



32. INSTALL OUTPUT SHAFT ADJUST NUT
  1. Using a belt and wooden block, securely fasten the transmission to the workbench.



    D033736
  1. Install a new spacer and a new No. 2 taper roller bearing.



    C199428E03
  1. Temporarily tighten a new nut by hand.
    Text in Illustration 
    *1
    Spacer
    *2
    No. 2 Taper Roller Bearing
    *3
    Nut

    HINT:
    Fit the spacer and No. 2 taper roller bearing securely.

  1. Move the shift and select lever shaft to N.

  1. Fit the bearing into the output shaft by turning the output shaft 15 times.



    C199430E01
  1. Using SST and a torque wrench, inspect preload (at starting)*1.

    SST
    09326-35010   (09326-03020)
    09326-35020  



    C199426E04
  1. Engage 5th gear, and then secure the input shaft using SST.
    Text in Illustration 
    *1
    Input Shaft

    SST
    09322-35010   (09322-03010, 09322-03020, 09322-03030, 90105-12087, 90170-12030, 94622-51200)

    HINT:
    1. Install SST securely so that (A) is in-line with the input shaft.
    2. Make sure that (A) moves back and forth by hand after installing SST.



    C199429E01
  1. Using SST, tighten the nut.

    SST
    09326-35020  

    Torque:
    Reference without SST:
    410 to 750 N*m{ 4180 to 7648 kgf*cm , 302 to 551 ft.*lbf }
    Reference with SST:
    374 to 684 N*m{ 3814 to 6974 kgf*cm , 275 to 502 ft.*lbf }

    NOTICE:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 100 mm (3.94 in.).
    2. The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 1040 mm (40.9 in.).
    3. The "with SST" torque value is effective when SST is parallel to the torque wrench.

  1. Move the shift and select lever shaft to N.

  1. Fit the bearing into the output shaft by turning the output shaft 15 times.



    C199430E01
  1. Using SST and a torque wrench, inspect preload (at starting)*2.

    SST
    09326-35010   (09326-03020)
    09326-35020  

  1. Adjust the preload so that the difference between *1 and *2 is within the specified range.

    Preload (at starting) without SST:
    *2 - *1 = 0.45 to 1.35 N*m (4.59 to 13.77 kgf*cm, 3.98 to 11.95 in.*lbf)

    Preload (at starting) with SST:
    *2 - *1 = 0.25 to 0.76 N*m (2.55 to 7.74 kgf*cm, 2.21 to 6.73 in.*lbf)

    NOTICE:
    1. If the result is not as specified, tighten and adjust the output shaft adjust nut.
    2. If the output shaft adjust nut is loose or removed due to excess preload, always replace the spacer and nut with new ones.



    D033734
  1. Using a chisel and hammer, stake the output shaft adjust nut.



33. INSTALL SPEEDOMETER DRIVE GEAR


D033733E01
  1. Install the oil receiver pipe, ball and speedometer drive gear.



    D033732E01
  1. Using a snap ring expander, install the snap ring.



34. INSTALL MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL


F051839E01
  1. Using SST and a hammer, tap a new oil seal into the extension housing in accordance with the dimension specified in the illustration.

    SST
    09950-60020   (09951-00640)
    09950-70010   (09951-07100)

    Dimension A:
    -0.5 to 0.5 mm (-0.197 to 0.197 in.)

  1. Apply gear oil to the lip of the oil seal.



35. INSTALL EXTENSION HOUSING SUB-ASSEMBLY


    D033760E04
  1. Apply seal packing to the extension housing, as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Parts must be assembled within 10 minutes of application. Otherwise, the packing material must be removed and reapplied.



    D033630E02
  1. Install the extension housing with the 8 bolts.
    Text in Illustration 
    *1
    Clamp

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



36. INSTALL SPEEDOMETER SENSOR


    D033775E02
  1. Install a new O-ring onto the speedometer sensor.
    Text in Illustration 
    *1
    O-ring
    *2
    Clip
    *3
    Speedometer Driven Gear

  1. Install the speedometer driven gear into the speedometer sensor with the clip.

    NOTICE:
    Be sure to install the clip in the direction shown in the illustration.



    D033774E01
  1. Install the speedometer driven gear with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



37. INSTALL SHIFT LEVER HOUSING


F051568E01
  1. Install the shift lever housing with the bolt.

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }



38. INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY


    D033761E03
  1. Apply seal packing to the floor shift control shift lever retainer, as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Parts must be assembled within 10 minutes of application. Otherwise, the packing material must be removed and reapplied.



    F051567E01
  1. Install the floor shift control shift lever retainer with the 4 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }