Home › ENGINE ยท 1GR-FE › EMISSION CONTROL › CANISTER

CANISTER > INSTALLATION

for Preparation Click here



1. INSTALL CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY
  1. Install a new charcoal canister leak detection pump with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Do not allow foreign matter such as grease, oil or water to adhere to the O-rings.
    2. Ensure that the claws are engaged properly.

  1. Connect the vacuum hose.



2. INSTALL CHARCOAL CANISTER ASSEMBLY
  1. Connect the fuel tank vent hose.

    1. Align the fuel tank vent hose connector with the pipe, then push in the fuel tank vent connector until the retainer makes a "click" sound to connect the fuel tank vent hose to the charcoal canister.

      NOTICE:
      1. Check that there are no scratches or foreign objects on the disconnected parts of the fuel tank vent connector and pipe before performing the work.
      2. After connecting the fuel tank vent hose, check that the fuel tank vent hose is securely connected by pulling the quick connector.

  1. Install the charcoal canister with the bolt and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the EVAP tube.

  1. Connect the connector.



3. INSTALL NO. 2 CHARCOAL CANISTER FILTER
  1. Install the No. 2 charcoal canister filter with the nut.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the breather hose to the charcoal canister.

  1. Engage the clamp.

  1. Connect the breather hose to the pipe.

  1. Connect the EVAP pipe to the clamp.

  1. Install the ABS wire harness bracket with the bolt.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



4. INSTALL FUEL TANK ASSEMBLY
  1. Set the fuel tank assembly onto the mission jack.

  1. Connect the fuel tank vent hose.

    1. Align the fuel tank vent connector with the pipe, then push in the fuel tank vent connector until the retainer makes a "click" sound to connect the fuel tank vent hose to the fuel suction plate.

      NOTICE:
      1. Check that there are no scratches or foreign objects around the connected part of the fuel tank vent connector and plug before performing this work.
      2. After connecting the fuel tank vent hose, check that the fuel tank vent hose is securely connected by pulling the quick connector.

  1. Connect the fuel pump connector.

  1. Install the fuel pump cover.

  1. Connect the fuel tank to filler pipe hose.

  1. Install the 2 fuel tank bands.

    1. Install the 2 fuel tank bands with the 2 pins and 2 clips.

    2. Install the 2 fuel tank bands with the 2 bolts.

      Torque:
      62 N*m{ 632 kgf*cm , 46 ft.*lbf }



    B079934E02
  1. Connect the fuel tank breather tube.

    1. Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a "click" sound to connect the fuel tank vent breather tube.

      NOTICE:
      1. Check that there are no scratches or foreign objects around the connected part of the fuel tube connector and pipe before performing this work.
      2. After connecting the fuel tank breather tube, check that the fuel pump tube is securely connected by pulling the fuel tube connector and pipe.

    2. Install the checker onto the pipe.

  1. Tighten the clamp bolt.



5. CONNECT FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE


A098610E09
  1. Connect the fuel tank main tube and return tube.

    1. Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a "click" sound to connect the fuel tank main tube and return tube.

      NOTICE:
      1. Check that there are no scratches or foreign objects around the connected part of the fuel tube connector and pipe before performing this work.
      2. After connecting the fuel tube connector, check that the fuel tube connector and pipe are securely connected by pulling them.

    2. Install the fuel pipe clamp.



6. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Off Road Package)
  1. Install the fuel tank protector LWR with the 4 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. CHECK FOR FUEL LEAKAGE