Home › ENGINE ยท 1GR-FE › EMISSION CONTROL › CANISTER

CANISTER > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


4. DISCONNECT FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE


G036078E01
  1. Remove the fuel pipe clamp.



    A121079E01
  1. Disconnect the fuel tank main tube and fuel tank return tube.

    1. Pinch the retainer as illustrated, then pull the fuel tube connectors out of the pipes.

      NOTICE:
      1. Remove any dirt and foreign objects from the fuel tube connector before performing this work.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
      6. If the fuel tube connector and pipe are stuck, push and pull to release them.



5. REMOVE FUEL TANK ASSEMBLY


G036080E01
  1. Loosen the clamp bolt.

  1. Disconnect the fuel breather tube.

    1. Remove the checker of the fuel tube connector from the pipe.

    2. Pinch the retainer of the fuel tube connector, then pull the tube connector out of the pipe.

      NOTICE:

      1. B079934E01
        Remove any dirt and foreign objects from the fuel tube connector before performing this work.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
      6. If the fuel tube connector and pipe are stuck, push and pull to release them.

  1. Hold the fuel tank using the mission jack.



    G036081E01
  1. Remove the 2 fuel tank bands.

    1. Remove the 2 bolts.

    2. Remove the 2 clips and 2 pins, then remove the 2 fuel tank bands.

  1. Slightly jack the fuel tank down and separate the fuel tank to filler pipe hose from the inlet pipe.

    NOTICE:
    Slowly jack down the fuel tank so as not to tear the wire harness and hose.

  1. Remove the fuel pump cover.

  1. Disconnect the fuel pump connector.

  1. Disconnect the fuel tank vent hose.

    1. Pinch the retainer and pull the fuel tank vent hose connector out of the charcoal canister to disconnect the fuel tank vent hose from the charcoal canister.

      NOTICE:
      1. Remove any dirt and foreign objects from the fuel tank vent hose connector before performing this work.
      2. Do not allow any scratches of foreign objects on the parts when disconnecting, as the fuel tank vent hose connector has the O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tank vent hose.
      6. If the fuel tank vent connector and pipe are stuck, push and pull to release them.



  1. Remove the fuel tank assembly.


    G036082E01



6. REMOVE NO. 2 CHARCOAL CANISTER FILTER


A266609
  1. Remove the bolt, then remove the ABS wire harness bracket from the charcoal canister.



    G036109E01
  1. Release the EVAP pipe from the hose clamp.

  1. Disconnect the breather hose from the pipe.

  1. Disengage the hose clamp.



    G036108E01
  1. Disconnect the breather hose from the charcoal canister.



    G036107E01
  1. Remove the nut, then remove the No. 2 charcoal canister filter.



7. REMOVE CHARCOAL CANISTER ASSEMBLY


G036105E01
  1. Disconnect the connector.

  1. Disconnect the EVAP tube.



    G036104E01
  1. Remove the bolt and 2 nuts, then remove the charcoal canister.



    G036103E02
  1. Disconnect the fuel tank vent hose.

    1. Pinch the retainer and pull the fuel tank vent hose connector out of the charcoal canister to disconnect the fuel tank vent hose from the charcoal canister.
      Text in Illustration 
      *a
      Pinch
      *b
      Push

      NOTICE:
      1. Remove any dirt and foreign objects from the fuel tank vent hose connector before performing the work.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tank vent hose connector has the O-ring that seals the pipe.
      3. Perform the work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tank vent hose.
      6. If the fuel vent connector and pipe are stuck, push and pull them to release.



8. REMOVE CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY
  1. Before removing the charcoal canister leak detection pump, clean the canister by blowing air on its outside to ensure that the canister is free of foreign matter.

    NOTICE:
    1. Make sure to clean the canister using only air.
    2. Do not blow air into canister parts.
    3. Do not use gasoline, thinners or solvents.



    A261699
  1. Disconnect the vacuum hose.

  1. Remove the 3 bolts and charcoal canister leak detection pump.



    A259576
  1. Check if the canister contains foreign matter such as mud or water.

    1. Visually check that the inside of the canister is free of foreign matter.

    2. Hold the canister upside down to make sure that the canister is free of foreign matter. If the canister contains foreign matter, replace the canister.