MANUAL TRANSMISSION ASSEMBLY > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY |
![]() |
Disengage the 4 clips and claw, and remove the console upper rear panel sub-assembly.
| 3. REMOVE REAR CONSOLE BOX ASSEMBLY |
![]() |
Remove the console box carpet.
![]() |
Remove the 2 screws <F> and 2 bolts <B>.
Disengage the 4 claws and remove the rear console box assembly.
| 4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
| 5. REMOVE FRONT CONSOLE BOX |
![]() |
Remove the shift knob.
Remove the 2 screws <F>.
Disengage the 2 clips and claw, and remove the front console box.
| 6. REMOVE SHIFT LEVER BOOT ASSEMBLY |
![]() |
Remove the 2 screws and 2 clips, then remove the shift lever boot.
| 7. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY |
![]() |
Separate the shift lever cap boot from the manual transmission.
![]() |
Cover the shift lever cap with a cloth.
Pressing down on the shift lever cap, turn it counterclockwise to remove the shift lever.
Pull out the shift lever.
| 8. REMOVE NO. 2 ENGINE UNDER COVER |
| 9. DRAIN MANUAL TRANSMISSION OIL |
Remove the drain plug, gasket and then drain the manual transmission oil.
Install a new gasket and drain plug.
| 10. REMOVE EXHAUST PIPE ASSEMBLY |
Remove the 2 nuts, then remove the exhaust front pipe.
| 11. REMOVE FRONT PROPELLER SHAFT ASSEMBLY |
![]() |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 12. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
![]() |
Place matchmarks on the propeller shaft flange and differential.
Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.
![]() |
Remove the 2 center support bearing bolts from the frame crossmember.
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 13. REMOVE NO. 2 MANIFOLD STAY |
![]() |
Remove the 3 bolts and manifold stay No. 2.
| 14. REMOVE MANIFOLD STAY |
![]() |
Remove the 3 bolts and manifold stay.
| 15. REMOVE STARTER ASSEMBLY |
![]() |
Disconnect the terminal 50 connector from the starter assembly.
Remove the nut, then remove the wire harness from terminal 30.
Remove the 2 bolts, then remove the starter assembly.
| 16. REMOVE NO. 1 CLUTCH HOUSING COVER |
![]() |
Remove the 3 bolts and clutch housing cover No. 1.
| 17. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY |
![]() |
Remove the 2 bolts and pull out the clutch release cylinder.
| 18. REMOVE CLUTCH ACCUMULATOR ASSEMBLY |
![]() |
Using union nut wrench, disconnect the 2 flexible hose tubes from the clutch accumulator.
![]() |
Remove the 3 bolts and clutch accumulator.
| 19. SUPPORT MANUAL TRANSMISSION WITH TRANSFER |
Support the manual transmission with a transmission jack.
| 20. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Remove the 4 bolts on the frame crossmember sub-assembly No. 3.
Remove the 4 nuts, 4 bolts and frame crossmember sub-assembly No. 3.
| 21. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR |
![]() |
Remove the 4 bolts and engine mounting insulator rear from the manual transmission.
| 22. DISCONNECT CONNECTOR |
Tilt down the transmission.
Disconnect the transfer shift actuator connector.
Disconnect the transfer indicator switch No. 1 connector.
Disconnect the transfer indicator switch No. 2 connector.
Disconnect the speedometer sensor connector.
Disconnect the back up lamp switch connector.
| 23. DISCONNECT WIRE HARNESS |
| 24. REMOVE MANUAL TRANSMISSION WITH TRANSFER |
![]() |
Remove the 9 bolts.
Separate and remove the manual transmission.
| 25. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY |
![]() |
Remove the 5 bolts and manual transmission case cover.
| 26. REMOVE TRANSFER ASSEMBLY |
![]() |
Remove the 8 transfer adaptor rear mounting bolts.
Pull the transfer straight up and remove it from the transmission.