Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock) > INSTALLATION

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY


F051366E03
  1. Remove any dust and oil from the differential carrier assembly and contact surface of the axle housing.

  1. Apply liquid gasket to both sides of a new gasket.
    Text in Illustration 
    *1
    Liquid Gasket

    NOTICE:
    Do not put the liquid gasket on the stud bolt.

  1. Install the gasket and the differential carrier assembly with the 10 nuts and 10 washers.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



2. INSTALL REAR AXLE SHAFT WITH BACKING PLATE LH


F052131
  1. Install a new O-ring.

  1. Install the rear axle shaft with backing plate with the 4 nuts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



3. INSTALL REAR AXLE SHAFT WITH BACKING PLATE RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL NO.3 PARKING BRAKE CABLE ASSEMBLY


D028121
  1. Install the parking brake cable with the 2 bolts onto the backing plate.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL NO.2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Use the same procedure as for the LH side.



6. INSTALL REAR SPEED SENSOR LH


F050583
  1. Install the rear speed sensor with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Make sure that the sensor tip is clean.

  1. Connect the speed sensor connector.



7. INSTALL REAR SPEED SENSOR RH

HINT:
Use the same procedure as for the LH side.



8. INSTALL REAR BRAKE SHOE


C179336E01
  1. Apply high temperature grease to the adjusting bolt.



    F050550
  1. Install the parking brake shoe lever LH and parking brake shoe strut set with the shoe return spring onto the rear brake shoe.



    F050544
  1. Using pliers, install the parking brake shoe strut set, parking brake reaction lever and parking brake shoe lever LH with 2 new C-washers.



    F042688
  1. Using needle-nose pliers, connect the parking brake cable No. 3 to the parking brake shoe lever LH.



    F050543E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



9. INSTALL FRONT BRAKE SHOE
  1. Install the automatic adjust lever LH, automatic adjust lever spring and parking brake shoe strut lower onto the front brake shoe.



    F050542E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



    F042698
  1. Install the tension spring onto the front brake shoe and rear brake shoe.



    F050551
  1. Using needle-nose pliers, install the return spring.



    F050540E01
  1. Using SST, install the shoe return spring onto the front brake shoe.

    SST
    09921-00010  



10. INSPECT REAR DRUM BRAKE INSTALLATION


  1. Check that each part is installed properly.


    F050552E01



    F050553E01
  1. Measure the brake drum inside diameter and the diameter of the brake shoes. Check that difference between the diameters is the specified shoe clearance.

    Shoe clearance:
    0.5 mm (0.0197 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and the drum.



11. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY
  1. Install a new drum gasket onto the rear brake drum.

  1. Install the rear brake drum.



12. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


F040023E02
  1. Provisionally install the hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 15 notches.

  1. Install the hole plug.



13. INSTALL PROPELLER SHAFT ASSEMBLY (for 2WD Regular Cab)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft assembly into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



14. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 2WD Except Regular Cab)


D033911E01
  1. Remove SST from the extension housing.

  1. Install the propeller shaft into the extension housing.



    C060588E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with the 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.



    F052184E02
  1. Adjust the center support bearing.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing to keep the intervals, as shown.
    2. In the same condition, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.039 to 0.039 in.) of each other in the vehicle's longitudinal direction when the vehicle is unladen.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



15. INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD Regular Cab)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C060588E01
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



16. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD Expect Regular Cab)


C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098708E02
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    D033899E01
  1. Provisionally install the center support bearing with 2 mounting bolts.

    HINT:
    Make sure the bearing is installed with the drain hole facing downwards.

  1. Torque the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



17. FILL RESERVOIR WITH BRAKE FLUID (for Hydraulic Brake Booster)

Fluid:
SAE J1703 or FMVSS NO. 116 DOT3



18. FILL RESERVOIR WITH BRAKE FLUID (for Vacuum Brake Booster)


C187250

Fluid:
SAE J1703 or FMVSS No. 116 DOT3



19. BLEED MASTER CYLINDER (for Vacuum Brake Booster)
Click here

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C187279
  1. Using a union nut wrench, separate the brake tubes from the master cylinder.



    C187251
  1. Slowly depress the brake pedal and hold it there (Step A).



    C187252
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C187280E01
  1. Using a union nut wrench, install the brake tubes into the master cylinder.

    Torque:
    without union nut wrench:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }
    with union nut wrench:
    18 N*m{ 187 kgf*cm , 13 ft.*lbf }

    HINT:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 20 mm (0.787 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.



20. BLEED BRAKE LINE (for Hydraulic Brake Booster)
  1. Turn the ignition switch to ON, and wait until the pump motor has stopped.

    HINT:
    Pump operating sound can be heard.



    F052299
  1. Front brake line.

    1. Connect the vinyl tube to the brake caliper.

    2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down (step D).

    3. At the point when the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (step E).

    4. Repeat step D and E until all the air in the fluid has been bled out.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



    F052424
  1. Rear brake line.

    1. Connect the vinyl tube to the wheel cylinder.

    2. Depress the brake pedal, hold it, and then loosen the bleeder plug.

      HINT:
      Brake fluid is pumped out automatically.

    3. Loosen the bleeder plug and release air.

      NOTICE:
      Keep brake fluid in the reservoir tank above the MIN line during the above procedures.

    4. When the air is completely bled out of the brake fluid through the bleeder plug, tighten the bleeder plug.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    5. Repeat the above procedures to bleed the other brake line.



21. BLEED BRAKE LINE (for Vacuum Brake Booster)


C187268
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



22. INSPECT FLUID LEVEL IN RESERVOIR (for Hydraulic Brake Booster)


    C172184
  1. Turn the ignition switch to OFF, and depress the brake pedal more than 40 times (until the pedal reaction feels light and pedal stroke becomes longer), and adjust the fluid level to the MAX level.

  1. When the ignition switch is turned to the ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm from the level when the ignition switch is off (normal).

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



23. INSPECT FLUID LEVEL IN RESERVOIR (for Vacuum Brake Booster)


A261799
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



24. INSPECT FOR BRAKE FLUID LEAK


25. ADD DIFFERENTIAL OIL


26. INSPECT DIFFERENTIAL OIL


D025304E37
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the differential carrier assembly with differential gear oil.

    Oil type and viscosity:
    Toyota Genuine Differential gear oil LT APL 75W-85 GL-5 or equivalent.

    Capacity:
    Front differential carrier assembly:
    1.45 to 1.55 liters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)
    Rear differential carrier assembly (for 2WD):
    3.26 to 3.36 liters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Rear differential carrier assembly (for Pre, 4WD):
    2.75 to 2.85 liters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



27. INSPECT FOR DIFFERENTIAL OIL LEAK


28. INSTALL REAR WHEEL

Torque:
113 N*m{ 1152 kgf*cm , 83 ft.*lbf }



29. INSPECT PARKING BRAKE PEDAL TRAVEL (for Automatic Transaxle)
  1. Slowly depress the parking brake pedal to the fully applied position, and count the number of clicks.

    Parking brake pedal travel at 300 N (31 kgf, 67 lbf):
    7 to 10 clicks



30. INSPECT PARKING BRAKE LEVER TRAVEL (for Manual Transaxle)
  1. Slowly pull the parking brake lever to the fully applied position, and count the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    7 to 10 clicks



31. ADJUST PARKING BRAKE PEDAL TRAVEL (for Automatic Transaxle)
  1. Confirm that the parking brake pedal is released.



    F050697E01
  1. Loosen the lock nut (labeled A) and turn the adjusting nut (labeled B) until the parking brake pedal travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light comes on.



32. ADJUST PARKING BRAKE LEVER TRAVEL (for Manual Transaxle)
  1. Confirm that the parking brake lever is released.



    F050697E01
  1. Loosen the lock nut (labeled A) and turn the adjusting nut (labeled B) until the parking brake lever travel is corrected to the specified value.

  1. Tighten the lock nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the parking brake lever indicator light comes on.



33. CHECK VSC SENSOR SIGNAL (for Hydraulic Brake Booster)
(Click here)


34. CHECK VSC SENSOR SIGNAL (for Vacuum Brake Booster)
(Click here)