Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/o Differential Lock) > REMOVAL

for Preparation Click here



1. REMOVE REAR WHEEL


2. DRAIN BRAKE FLUID


3. DRAIN DIFFERENTIAL OIL


4. REMOVE PROPELLER SHAFT ASSEMBLY (for 2WD Regular Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    D033911E01
  1. Remove the propeller shaft.

  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



5. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 2WD Except Regular Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts and 4 washers, and remove the propeller shaft.



    D033912
  1. Remove the 2 center support bearing bolts from the frame crossmember.



    D033911E01
  1. Pull out the propeller shaft.

  1. Insert SST into the transmission to prevent oil leakage.

    SST
    09325-40010  



6. REMOVE PROPELLER SHAFT ASSEMBLY (for 4WD Regular Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    C098709E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



7. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD Except Regular Cab)


C060588E01
  1. Place matchmarks on the propeller shaft flange and differential.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft.



    D033912
  1. Remove the 2 center support bearing bolts from the frame crossmember.



    C098709E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



8. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY


F040009
  1. Release the parking brake, and remove the rear brake drum.
    If the rear brake drum cannot be removed easily, perform the following procedures.

  1. Remove the hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjusting lever away from the adjuster.

  1. Using another screwdriver, contract the brake shoe by turning the adjusting bolt.

  1. Remove the drum gasket from the rear brake drum.



9. REMOVE FRONT BRAKE SHOE


F050540E01
  1. Using SST, remove the shoe return spring from the front brake shoe.

    SST
    09921-00010  



    F050541E01
  1. Using needle-nose pliers, remove the return spring.



    F050542E01
  1. Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.

    SST
    09718-00010  

  1. Remove the parking brake shoe strut lower.

  1. Remove the tension spring and front brake shoe.

  1. Remove the automatic adjust lever spring and automatic adjust lever LH from the front brake shoe.



10. REMOVE REAR BRAKE SHOE


F050543E01
  1. Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.

    SST
    09718-00010  



    F042688E01
  1. Using needle-nose pliers, disconnect the parking brake cable No. 3 and remove the rear brake shoe.



    F050544E01
  1. Using a screwdriver, remove the 2 C-washers, parking brake shoe lever, parking brake reaction lever and parking brake shoe strut set.



11. SEPARATE REAR SPEED SENSOR LH


F050583
  1. Disconnect the speed sensor connector.

  1. Remove the nut and speed sensor rear.

    NOTICE:
    1. Do not attach any foreign matter to the sensor tip.
    2. Ensure that no foreign matter enters the sensor installation hole.



12. SEPARATE REAR SPEED SENSOR RH

HINT:
Use the same procedure as for the LH side.



13. SEPARATE NO.3 PARKING BRAKE CABLE ASSEMBLY


D028121
  1. Remove the 2 bolts and disconnect the parking brake cable from the backing plate.



14. SEPARATE NO.2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Use the same procedure as for the LH side.



15. REMOVE REAR AXLE SHAFT WITH BACKING PLATE


F052131
  1. Remove the 4 nuts and rear axle shaft with backing plate.

  1. Remove the O-ring.



16. REMOVE REAR AXLE SHAFT WITH BACKING PLATE

HINT:
Use the same procedure as for the LH side.



17. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY


C171931
  1. Remove the 10 nuts and the rear differential carrier assembly.

    NOTICE:
    Be careful not to damage the removal surface.

  1. Remove the rear differential carrier gasket from the rear differential carrier assembly.