Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY


C097020
  1. Connect the actuator hose and connector.

  1. Install the No. 1 mounting support with the 3 bolts.

    Torque:
    186 N*m{ 1899 kgf*cm , 138 ft.*lbf }

  1. Install the No. 2 mounting support with the 2 bolts.

    Torque:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }

  1. Install the No. 3 front differential support with the 2 bolts.

    Torque:
    108 N*m{ 1100 kgf*cm , 80 ft.*lbf }

  1. Support the front differential with a jack.

  1. Install the 2 front mounting bolts and nuts.

    Torque:
    137 N*m{ 1400 kgf*cm , 101 ft.*lbf }

  1. Install the No. 1 front differential mount nut.

    Torque:
    87 N*m{ 889 kgf*cm , 64 ft.*lbf }

  1. Install the front differential breather tube bracket with the bolt.

    Torque:
    13 N*m{ 129 kgf*cm , 8 ft.*lbf }

  1. Lower the jack.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


F042771
  1. Coat the spline of the inboard joint shaft with gear oil.

  1. Align the shaft splines and install the front drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing downward.
    2. Be careful not to damage the oil seal.

    HINT:
    Whether the inboard joint shaft is in contact with the pinion shaft or not can be confirmed from the sound or feeling when driving it.



3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL FRONT SUSPENSION LOWER ARM LH
  1. Install the front lower ball joint attachment with the 2 bolts.

    Torque:
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf }



5. INSTALL FRONT SUSPENSION LOWER ARM RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL TIE ROD END SUB-ASSEMBLY LH
  1. Install the tie rod end onto the steering knuckle arm.

  1. Install the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.



7. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



8. INSTALL FRONT SPEED SENSOR LH


C114967E02
  1. Install the front speed sensor with the bolt.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    NOTICE:
    Make sure that the sensor tip is clean.

  1. Connect the speed sensor connector.



9. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


G020162
  1. Install the front stabilizer bracket with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



11. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



12. INSTALL FRONT AXLE SHAFT LH NUT
  1. Install the front axle hub nut.

    Torque:
    235 N*m{ 2396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and a new cotter pin.

  1. Install the front axle hub grease cap.



13. INSTALL FRONT AXLE SHAFT RH NUT

HINT:
Use the same procedure as for the LH side.



14. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


C098708E03
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098709E02
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



15. ADD DIFFERENTIAL OIL


D025304E37
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the differential carrier assembly with differential gear oil.

    Oil type and viscosity:
    Toyota Genuine Differential gear oil LT APL 75W-85 GL-5 or equivalent.

    Capacity:
    Front differential carrier assembly:
    1.45 to 1.55 liters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)
    Rear differential carrier assembly (for 2WD):
    3.26 to 3.36 liters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Rear differential carrier assembly (for Pre, 4WD):
    2.75 to 2.85 liters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



16. INSPECT DIFFERENTIAL OIL


D025304E37
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the differential carrier assembly with differential gear oil.

    Oil type and viscosity:
    Toyota Genuine Differential gear oil LT APL 75W-85 GL-5 or equivalent.

    Capacity:
    Front differential carrier assembly:
    1.45 to 1.55 liters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)
    Rear differential carrier assembly (for 2WD):
    3.26 to 3.36 liters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Rear differential carrier assembly (for Pre, 4WD):
    2.75 to 2.85 liters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



17. INSPECT FOR DIFFERENTIAL OIL LEAK


18. INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 2 engine under cover sub-assembly with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



19. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover sub-assembly with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



20. INSTALL FRONT WHEEL

Torque:
113 N*m{ 1,152 kgf*cm , 83 ft.*lbf }



21. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



23. CHECK VSC SENSOR SIGNAL (for Hydraulic Brake Booster)
(Click here)


24. CHECK VSC SENSOR SIGNAL (for Vacuum Brake Booster)
(Click here)