AUTOMATIC TRANSMISSION FLUID > ADJUSTMENT |
| 1. BEFORE FILLING TRANSMISSION |
| 2. TRANSMISSION PAN FILL |
![]() |
Remove the refill plug and overflow plug.
| *1 | Refill Plug |
| *2 | Overflow Plug |
| *3 | Refill Hole |
![]() |
Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.
| *1 | Overflow Tube |
| *a | Specified Fluid Level |
Reinstall the overflow plug.
| 3. TRANSMISSION FILL |
Fill the transmission with the correct amount of fluid as listed in the table below.
Reinstall the refill plug to avoid fluid splash.
| Repair | Fill Amount |
| Transmission pan and drain plug removal | 1.7 liters (1.8 US qts, 1.5 Imp. qts) |
| Transmission valve body removal | 4.3 liters (4.5 US qts, 3.8 Imp. qts) |
| Torque converter removal | 5.4 liters (5.7 US qts, 4.8 Imp. qts) |
| 4. FLUID CIRCULATION |
Allow the engine to idle with the air conditioning off.
Move the shift lever through entire gear range to circulate fluid.
| 5. FLUID TEMPERATURE CHECK |
When using the Techstream:
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.
Check ATF temperature.
According to the display on the Techstream, perform the Active Test "Connect the TC and TE1".
Start the engine.
![]() |
When not using the Techstream (using indicator light):
| *a | Front view of DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Start the engine.
Slowly move the shift lever from P to L, and then return the shift lever to P.
![]() |
Move the shift lever to D, and quickly move back and forth between N and D (once within 1.5 seconds) for at least 6 seconds. This will activate the fluid temperature detection mode.
| *a | A/T OIL TEMP Warning Light |
When using the Techstream:
Return the shift lever to P and terminate the Active Test on the Techstream.
When not using the Techstream:
Return the shift lever to P and disconnect terminals 13 (TC) and 4 (CG).
Allow the engine to idle until the fluid temperature reaches 36 to 46°C (97 to 115°F).
The A/T OIL TEMP warning light will come on again when the fluid temperature reaches 36°C (97°F) and will blink when it exceeds 46°C (115°F).
| Below Proper Temperature | Proper Temperature | Higher than Proper Temperature |
| Data List: [A/T Oil Temperature 1] 36°C (97°F) or less | Data List: [A/T Oil Temperature 1] 36 to 46°C (97 to 115°F) | Data List: [A/T Oil Temperature 1] 46°C (115°F) or higher |
| A/T OIL TEMP warning light: Turn off | A/T OIL TEMP warning light: Turn on | A/T OIL TEMP warning light: Blinking |
| 6. FLUID LEVEL CHECK |
![]() |
Remove the overflow plug with the engine idling.
| *1 | Overflow Tube |
| *a | Specified Fluid Level |
Check that the fluid comes out of the overflow tube.
If fluid does not come out, proceed to step 7.
If fluid comes out, wait until the overflow slows to a trickle and proceed to step 8.
| 7. TRANSMISSION REFILL |
Install the overflow plug.
Stop the engine.
Remove the refill plug.
Add 0.4 liters (0.42 US qts, 0.35 Imp. qts) of fluid.
Allow the engine to idle and wait for 10 seconds.
Proceed to step 6.
| 8. COMPLETE |
Install the overflow plug with a new gasket.
Stop the engine.
Install the refill plug with a new gasket.