Home › ENGINE · 1GR-FE › ENGINE MECHANICAL › ENGINE

ENGINE > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT ENGINE COOLANT
  1. The engine coolant should be between the LOW and FULL lines when the engine is cold.
    If low, check for leakage and add Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology up to the FULL line.



2. INSPECT ENGINE OIL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the level gauge.
    If low, check for leakage and top oil up to the full level mark.

    NOTICE:
    Do not fill with engine oil to above the full level mark.



3. INSPECT BATTERY


G036166E01
  1. Check the voltage.

    1. If it has been less than 20 minutes since you stopped driving the vehicle or since the engine was stopped, turn the ignition switch and electrical systems (headlight, blower motor, rear defogger etc.) to the ON position for 60 seconds. This will remove the surface charge on the battery.

    2. Turn the ignition switch to OFF.

    3. Turn the electrical systems to OFF.

    4. Using a voltmeter, measure the battery voltage between the negative (-) and positive (+) terminals of the battery.

      Standard:
      12.6 to 12.9 V at 20°C(68°F)

      If the result is not as specified, replace the battery.



    G036167E01
  1. Check the indicator is as shown in the illustration.
    Indicator Color
    Condition
    Blue
    Ready
    White
    Charging Necessary
    Red
    Have battery checked by your Toyota dealer



4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


5. INSPECT SPARK PLUG

NOTICE:
  1. Never use a wire brush for cleaning.
  2. Never attempt to adjust the electrode gap on a used spark plug.
  3. The spark plug should be replaced every 200,000 km (120,000 miles).

  1. Remove the engine cover.

  1. Remove the air cleaner.

  1. Remove the ignition coil.

  1. Remove the spark plug.



    A110413E04
  1. Check the electrode.

    1. Using an ohmmeter, measure the insulation resistance.

      Correct insulation resistance:
      10 MΩ or more

      If the resistance is below the specified range, remove the spark plug.

      HINT:
      If an ohmmeter is not available, perform the following simple inspection.



    B001301E01
  1. Alternative inspection method:

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage on its threads and insulator.
    If there is damage, replace the spark plug. If not, reinstall the spark plug.

    Recommended spark plug:
    Manufacturer
    Spark Plug Type
    DENSO
    K20HR-U11
    NGK
    LFR6C11



    A088861E02
  1. Check the spark plug electrode gap.

    Standard electrode gap:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

    If the electrode gap is larger than the standard, replace the spark plug.



6. INSPECT DRIVE BELT


A058797E02
  1. Visually check the driver belt for excessive wear, frayed cords, etc. If any defect is found, replace the drive belt.

    HINT:
    Cracks on the rib side of a drive belt are considered acceptable. If the drive belt has chunks missing from the ribs, it should be replaced.



7. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems OFF.
  1. Operate the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.

  1. When using the Techstream.

    1. Connect the Techstream to the DLC3.

    2. Enter the following menu items:
      Select: Powertrain / Engine and ECT / Data List / IGN Advance.

    3. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24° BTDC @ idle (Transmission in neutral position)

    4. Check that the ignition timing advances immediately when the engine speed is increased.



    A118802E01
  1. When not using Techstream.

    1. Using SST, connect the terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be sure not to connect the terminals wrongly. It causes breakage of the engine.

    2. Remove the air cleaner.



    3. A076315E02
    4. Pull out the wire harness as shown in the illustration.

    5. Connect the tester probe of a timing light to the wire of the ignition coil connector for No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects the first signal.
      1. After checking, be sure to wrap the wire harness with tape.



    6. A076316E01
    7. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12° BTDC @ idle (Transmission in neutral position)

    8. Remove the SST from the DLC3.

    9. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24° BTDC @ idle (Transmission in neutral position)

    10. Install the air cleaner.



8. INSPECT ENGINE IDLING SPEED

NOTICE:
  1. Turn all the electrical systems OFF.
  1. Operate the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter the following menu items:
      Select: Powertrain / Engine and ECT / Data List / Engine Speed.

    3. Inspect the engine idling speed.

      Idling speed:
      650 to 750 rpm (Transmission in neutral position)



    A118802E02
  1. When not using the Techstream:

    1. Using SST, connect the terminal 8 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Race the engine speed at 2,500 rpm for approximately 90 seconds.

    3. Inspect the engine idling speed.

      Idling speed:
      650 to 750 rpm (Transmission in neutral position)



9. INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the circuit opening relay.

  1. Remove the V-bank cover.

  1. Remove the air cleaner assembly.

  1. Remove the ignition coils.

  1. Remove the spark plugs.



    A076317E01
  1. Inspect the cylinder compression pressure.

    1. Insert a compression gage into the spark plug hole.

      SST
      09992-00500  

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Compression pressure:
      1,300 kPa (13.3 kgf/cm2, 189 psi)

      Minimum pressure:
      1,000 kPa (10.2 kgf/cm2, 145 psi)

      Difference between each cylinder:
      100 kPa (1.0 kgf/cm2, 15 psi)

      NOTICE:
      1. Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
      1. Inspect the other cylinders in the same way.
      1. Measure the compression in as short a time as possible.

    4. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and repeat steps (1) through (3) for cylinders with low compression.

      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      1. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.



10. INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.

  1. Immediately check the CO/HC concentration during idling and/or at 2,500 rpm.

    HINT:
    1. Complete the measurement within 3 minutes.
    1. When carrying out the 2 modes (idling and 2,500 rpm) test, the measurement orders are prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check the heated oxygen sensor operation.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        1. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        1. Intake manifold
        1. Throttle body
        1. IAC valve
        1. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        1. Faulty engine coolant temperature sensor
        1. Faulty mass air flow meter
        1. Faulty ECM
        1. Faulty injectors
        1. Faulty throttle position sensor