Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REPLACEMENT

for Preparation Click here



1. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


A072957E01
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the oil pump assembly. Wrap a tip of the screwdriver with tape.



2. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


A076300E02
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09226-10010  

  1. Apply MP grease to the oil seal lip.



3. REMOVE REAR ENGINE OIL SEAL


A076248E02
  1. Using a screwdriver and hammer, tap the oil seal out.



4. INSTALL REAR ENGINE OIL SEAL


A076268E02
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.

    SST
    09223-78010  

  1. Apply MP grease to the oil seal lip.



5. REMOVE VALVE GUIDE BUSH


A075616E01
  1. Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).



    A075617E02
  1. Place the cylinder head on a wooden block.

  1. Using SST, tap out the valve guide bush.

    SST
    09201-10000  
    09201-01055  
    09950-70010   (09951-07100)



6. INSTALL VALVE GUIDE BUSH


A075618E01
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Bush bore diameter:
    10.295 to 10.315 mm (0.4053 to 0.4061 in.)

    If the bush bore diameter of the cylinder head is greater than 10.315 mm (0.4061 in.), machine the bush bore to the dimension of 10.345 to 10.365 mm (0.4073 to 0.4081 in.).

    Valve guide bush diameter:
    Item
    Specified Condition
    STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)



    A075616E01
  1. Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).



    A075619E03
  1. Place the cylinder head on a wooden block.

  1. Using SST, tap in a new valve guide bush to the specified protrusion height.

    SST
    09201-10000  
    09201-01055  
    09950-70010   (09951-07100)

    Protrusion height:
    9.3 to 9.7 mm (0.366 to 0.382 in.)



    A075620E01
  1. Using a sharp 5.5 mm reamer, ream the valve guide bush to the standard specified clearance between the valve guide bush and valve stem.

    Standard oil clearance::
    Item
    Specified Condition
    Intake
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)
    Exhaust
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)



7. REMOVE CONNECTING ROD SMALL END BUSH


EM06363E01
  1. Using SST and a press, press out the bushing.

    SST
    09222-30010  



8. INSTALL CONNECTING ROD SMALL END BUSH


A051812E01
  1. Align the oil holes of a new bushing and the connecting rod.



    EM06363E01
  1. Using SST and a press, press in the bushing.

    SST
    09222-30010  



    A121034E01
  1. Using a pin hole grinder, hone the bushing to the standard specified clearance between the bushing and piston pin.

    Standard oil clearance:
    0.005 to 0.011 mm (0.0002 to 0.0004 in.)

    HINT:
    Check the measurement at room temperature. Coat the piston pin with engine oil, and push it into the connecting rod with a thumb.