Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > INSPECTION

for Preparation Click here



1. INSPECT CAMSHAFTS


A005912E01
  1. Inspect the camshaft for runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum runout:
      0.06 mm (0.0024 in.)

      If the circle runout is greater than the maximum, replace the camshaft.



    EM02011E01
  1. Inspect the cam lobes.

    1. Using a micrometer, measure the cam lobe height.

      Standard cam lobe height:
      Intake 44.168 to 44.268 mm (1.7389 to 1.7428 in.)
      Exhaust 44.580 to 44.680 mm (1.7551 to 1.7591 in.)

      Minimum cam lobe height:
      Intake 44.018 mm (1.7330 in.)
      Exhaust 44.430 mm (1.7492 in.)

      If the cam lobe height is less than the minimum, replace the camshaft.



    A076249E03
  1. Inspect the camshaft journals.

    1. Using a micrometer, measure the journal diameter.

      No. 1 journal diameter:
      35.971 to 35.985 mm (1.4162 to 1.4167 in.)

      Other journal diameter:
      22.959 to 22.975 mm (0.9039 to 0.9045 in.)

      If the journal diameter is not as specified, check the oil clearance.



2. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the intake camshaft in a vise.

    NOTICE:
    Be careful not to damage the camshaft.



    A076250E02
  1. Align the knock pin hole in the camshaft timing gear assembly with the knock pin of the camshaft, and install the camshaft timing gear assembly with the bolt.

    Torque:
    100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }

  1. Confirm that the camshaft timing gear assembly is locked.



    G036837E02
  1. Release that lock pin.

    1. Cover 4 oil paths of cam journal with masking tape as shown in the illustration.

      HINT:
      One of the 2 grooves on the cam journal is for the retard side path (upper) and the other is for the advance side path (lower). Each groove has 2 oil paths. Plug one of the oil paths for each groove with a piece of rubber before wrapping the cam journal with tape.

    2. Puncture the tape covering the advance oil path and retard oil path on the opposite side of the groove as shown in the illustration.



    3. G036838E02
    4. Apply air pressure into two broken paths (the advance side path and the retard side path) of about 200 kPa (2.0 kgf/cm2).

      NOTICE:
      Cover the paths with a shop rag to avoid oil splashes.



    5. G036839E02
    6. Confirm that the camshaft timing gear assembly rotates in the timing advance direction when reducing the air pressure on the timing retard path.

      HINT:
      When the lock pin is released, the camshaft timing gear rotates in the advance direction.

    7. When the camshaft timing gear comes to the most advanced position, release the air pressure on the timing retard side path, and release that of the timing advance side path.

      NOTICE:
      Camshaft timing assembly gear occasionally shifts to the retard side abruptly if the air compression on the advanced side path is released first. This often causes the breakage of the lock pin.

  1. Check the smooth revolution.

    1. Rotate the camshaft timing gear several times within the movable range except for the most retarded position and check it rotates smoothly.

      Standard:
      Move smoothly in the range about 31°

      NOTICE:
      Be sure to perform this check by hand, instead of using air pressure.

  1. Check that the lock is in the most retarded position.

    1. Confirm that the camshaft timing gear assembly is locked in the most retarded position.



    G036840E02
  1. Remove the set bolt, then remove the camshaft timing gear assembly.

    NOTICE:
    Be sure not to remove the other 3 bolts.



3. INSPECT CYLINDER HEAD SET BOLT


A076820E01
  1. Using vernier calipers, measure the outer diameter of the bolt thread.

    Standard outer diameter:
    10.85 to 11.00 mm (0.4272 to 0.4331 in.)

    Minimum outer diameter:
    10.7 mm (0.421 in.)

    If the cylinder head set bolt is less than the minimum, replace the bolt.



4. INSPECT CHAIN SUB-ASSEMBLY


A053044E02
  1. Using a spring scale, apply 147 N (15.0 kgf, 33.1 lbf) to the chain and measure the length.

    Maximum chain length:
    146.8 mm (5.780 in.)

    NOTICE:
    Measure the length at least 3 places and calculate the average length.

    If the chain length is greater than the maximum, replace the chain.



5. INSPECT NO.2 CHAIN SUB-ASSEMBLY


A053044E02
  1. Using a spring scale, apply 147 N (15.0 kgf, 33.1 lbf) to the chain and measure the length.

    Maximum chain length:
    146.8 mm (5.780 in.)

    NOTICE:
    Measure the length at least 3 places and calculate the average length.

    If the chain length is greater than the maximum, replace the chain.



6. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY


A076255E01
  1. Wrap the No. 1 chain around the larger gear of timing gear assembly.

  1. Using vernier caliper, measure the timing gear with the chain wrapped.

    Minimum gear diameter (with chain):
    115.5 mm (4.547 in.)

    NOTICE:
    Vernier caliper must be in contact with the chain rollers when measuring.

    If the gear diameter is less than the minimum, replace the No. 1 chain and the camshaft timing gear assembly.



    A076256E01
  1. Wrap the No. 2 chain around the smaller gear of timing gear assembly.

  1. Using vernier calipers, measure the timing gear with the chain wrapped.

    Minimum gear diameter (with chain):
    73.1 mm (2.878 in.)

    NOTICE:
    The vernier calipers must be in contact the chain rollers when measuring.

    If the gear diameter is less than the minimum, replace the No. 2 chain and the camshaft timing gear assembly.



7. INSPECT CAMSHAFT TIMING GEAR OR SPROCKET


A076257E01
  1. Wrap the No. 2 chain around the timing gear.

  1. Using vernier calipers, measure the camshaft timing gear diameter with the chain wrapped.

    Minimum gear diameter (with chain):
    73.1 mm (2.878 in.)

    NOTICE:
    The vernier calipers must be in contact the chain rollers when measuring.

    If the gear diameter is less than the minimum, replace the No. 2 chain and camshaft timing gear.



8. INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET


A076258E01
  1. Wrap the No. 1 chain around the timing gear.

  1. Using vernier calipers, measure the timing gear diameter with the chain wrapped.

    Minimum gear diameter (with chain):
    61.0 mm (2.402 in.)

    NOTICE:
    The vernier calipers must be in contact with the chain rollers when measuring.

    If the gear diameter is less than the minimum, replace the No. 1 chain and the crankshaft timing gear.



9. INSPECT IDLE SPROCKET ASSEMBLY


A076259E01
  1. Wrap the No. 1 chain around the idle sprocket.

  1. Using vernier caliper, measure the idle sprocket with the chain wrapped.

    Minimum gear diameter (with chain):
    61.0 mm (2.402 in.)

    NOTICE:
    The vernier caliper must be in contact with the chain rollers when measuring.

    If the gear diameter is less than the minimum, replace the No. 1 chain and idle sprocket.



10. INSPECT NO.1 IDLE GEAR SHAFT


A076260E01
  1. Using a micrometer, measure the idle gear shaft diameter.

    Idle gear shaft diameter:
    22.987 to 23.000 mm (0.9050 to 0.9055 in.)



    A076261E01
  1. Using a caliper gauge, measure the internal diameter of the idle gear.

    Idle gear internal diameter:
    23.02 to 23.03 mm (0.9063 to 0.9067 in.)

  1. Subtract the idle gear shaft diameter measurement from the idle gear internal diameter measurement.

    Standard oil clearance:
    0.020 to 0.043 mm (0.0008 to 0.0017 in.)

    Maximum oil clearance:
    0.093 mm (0.0037 in.)



11. INSPECT NO.1 CHAIN TENSIONER ASSEMBLY


A076262E02
  1. Check that the plunger moves smoothly when the ratchet pawl is raised with finger.

  1. Release the ratchet pawl, then check that the plunger is locked in place by the ratchet pawl and does not move when pushing it with finger.



12. INSPECT NO.2 CHAIN TENSIONER ASSEMBLY


A076263E02
  1. Check that the plunger moves smoothly.

  1. Measure the wear of the chain tensioner slipper.

    Maximum wear:
    1.0 mm (0.039 in.)

    If the wear is greater than the maximum, replace the chain tensioner No. 2.



13. INSPECT NO.3 CHAIN TENSIONER ASSEMBLY


A076264E02
  1. Check that the plunger moves smoothly.

  1. Measure the wear of the chain tensioner slipper.

    Maximum wear:
    1.0 mm (0.039 in.)

    If the wear is greater than the maximum, replace the chain tensioner No. 3.



14. INSPECT CHAIN TENSIONER SLIPPER


A076265E02
  1. Measure the wear of the tensioner slipper.

    Maximum wear:
    1.0 mm (0.039 in.)

    If the thickness is greater than the maximum, replace the tensioner slipper.



15. INSPECT NO.1 CHAIN VIBRATION DAMPER


A076266E02
  1. Measure the wear of the vibration damper No. 1.

    Maximum wear:
    1.0 mm (0.039 in.)

    If the thickness is greater than the maximum, replace the vibration damper No. 1.



16. INSPECT NO.2 CHAIN VIBRATION DAMPER


A076267E02
  1. Measure the wear of the vibration damper No. 2 .

    Maximum wear:
    1.0 mm (0.039 in.)

    If the thickness is greater than the maximum, replace the vibration damper No. 2.



17. INSPECT CYLINDER HEAD SUB-ASSEMBLY


A075609E03
  1. Inspect the cylinder head for warpage.

    1. Using a precision straight edge and feeler gauge, measure the warpage on the cylinder block side and the intake and exhaust sides.

      Maximum warpage:
      0.10 mm (0.0039 in.)

      If the warpage is greater than the maximum, replace the cylinder head.



    A075610E01
  1. Inspect the cylinder head for crack.

    1. Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.
      If cracked, replace the cylinder head.



18. CLEAN VALVE


EM00580E01
  1. Using a gasket scraper, chip off any carbon from the valve head.

  1. Using a wire brush, thoroughly clean the valve.



19. INSPECT VALVE


A032770E01
  1. Inspect valve stem diameter.

    1. Using a micrometer, measure the diameter of the valve stem.

      Valve stem diameter:
      Item
      Specified Condition
      Intake
      5.470 to 5.485 mm (0.2154 to 0.2159 in.)
      Exhaust
      5.465 to 5.480 mm (0.2152 to 0.2158 in.)



    A075611E03
  1. Inspect valve face angle.

    1. Grind the valve enough to remove any pits and carbon.

    2. Check that the valve is ground to the correct valve face angle.

      Valve face angle:
      45.5°



    EM00181E02
  1. Inspect valve head margin thickness.

    1. Using vernier calipers, check the valve head margin thickness.

      Standard margin thickness:
      1.0 mm (0.039 in.)

      Minimum margin thickness:
      0.5 mm (0.020 in.)

      If the margin thickness is less than the minimum, replace the valve.



    EM02534E08
  1. Inspect overall length.

    1. Using vernier calipers, check the overall length.

      Standard overall length:
      Item
      Specified Condition
      Intake
      106.95 mm (4.2106 in.)
      Exhaust
      105.80 mm (4.1654 in.)

      Minimum overall length:
      Item
      Specified Condition
      Intake
      106.70 mm (4.2008 in.)
      Exhaust
      105.55 mm (4.1555 in.)

      If the overall length is less than the minimum, replace the valve.



    EM00255E01
  1. Inspect valve stem tip.

    1. Check the surface of the valve stem tip for wear.

      NOTICE:
      Do not grind to less than the minimum length.

      If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.



20. CLEAN VALVE SEAT


A075612E01
  1. Using a 45° carbide cutter, resurface the valve seats.

  1. Clean the valve seats.



21. INSPECT VALVE SEAT


P012729E01
  1. Apply a light coat of prussian blue (or white lead) to the valve face.

  1. Lightly press the valve against the valve seat.

    NOTICE:
    Do not rotate the valve.

  1. Check the valve face and seat according to the following procedure.

    1. If blue appears 360° around the face, the valve is concentric.
      If not, replace the valve.

    2. If the blue appears 360° around the valve seat, the guide and face are concentric.
      If not, resurface the valve seat.

    3. Check that the seat is in contact with the middle of the valve face with the following width.

      Standard width:
      1.0 to 1.4 mm (0.039 to 0.055 in.)



22. INSPECT INNER COMPRESSION SPRING


EM00988E03
  1. Inspect the deviation.

    1. Using steel squares, measure the deviation of the inner compression spring.

      Maximum deviation:
      2.0 mm (0.079 in.)

      If the deviation is greater than the maximum, replace the inner compression spring.



    EM00801E01
  1. Inspect the free length.

    1. Using vernier calipers, measure the free length of the inner compression spring.

      Free length:
      47.80 mm (1.8819 in.)

      If the free length is not as specified, replace the inner compression spring.



    EM00281E01
  1. Inspect the tension.

    1. Using a spring tester, measure the tension of the inner compression spring at the specified installed length.

      Installed tension:
      186.2 to 205.8 N (19.0 to 21.0 kgf, 41.9 to 46.3 lbf) at 33.3 mm (1.311 in.)

      If the installed tension is not as specified, replace the inner compression spring.



23. INSPECT VALVE GUIDE BUSH OIL CLEARANCE


A075615E01
  1. Using a caliper gauge, measure the internal diameter of the valve guide bush.

    Inside diameter:
    5.51 to 5.53 mm (0.2169 to 0.2177 in.)

  1. Subtract the valve stem diameter measurement (Step 8) from the valve guide bush internal diameter measurement.

    Standard oil clearance:
    Item
    Specified Condition
    Intake
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)
    Exhaust
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)

    Maximum oil clearance:
    Item
    Specified Condition
    Intake
    0.08 mm (0.0031 in.)
    Exhaust
    0.10 mm (0.0039 in..)

    If the oil clearance is greater than the maximum, replace the valve and valve guide bush.



24. INSPECT VALVE LIFTER


P016860E01
  1. Using a micrometer, measure the valve lifter diameter.

    Valve lifter diameter:
    30.966 to 30.976 mm (1.2191 to 1.2195 in.)



25. INSPECT VALVE LIFTER OIL CLEARANCE


A075621E02
  1. Using a caliper gauge, measure the lifter bore diameter of the cylinder head.

    Lifter bore diameter:
    31.009 to 31.025 mm (1.2208 to 1.2215 in.)

  1. Subtract the valve lifter diameter measurement (Step 16) from the lifter bore diameter measurement.

    Standard oil clearance:
    0.033 to 0.059 mm (0.0013 to 0.0023 in.)

    Maximum oil clearance:
    0.08 mm (0.0031 in.)

    If the oil clearance is greater than the maximum, replace the valve lifter.
    If necessary, replace the cylinder head.



26. INSPECT CAMSHAFT OIL CLEARANCE


A075622E02
  1. Clean the camshaft bearing caps, camshaft bearings and camshaft journals.

  1. Install the camshaft bearing (Click here or Click here).

  1. Place the camshaft on the cylinder head.

  1. Lay a strip of Plastigage across each camshaft journal.

  1. Install the camshaft bearing caps (Click here or Click here).

    NOTICE:
    Do not turn the camshafts.

  1. Remove the camshaft bearing caps (Click here or Click here).



    A075623E01
  1. Measure the Plastigage at its widest point.

    Standard oil clearance (Cylinder head RH):
    Item
    Specified Condition
    No. 1 (Intake)
    0.008 to 0.038 mm (0.0003 to 0.0015 in.)
    No. 1 (Exhaust)
    0.040 to 0.079 mm (0.0016 to 0.0031 in.)
    Others
    0.025 to 0.062 mm (0.0010 to 0.0024 in.)

    Standard oil clearance (Cylinder head LH):
    Item
    Specified Condition
    No. 1
    0.040 to 0.079 mm (0.0016 to 0.0031 in.)
    Others
    0.025 to 0.062 mm (0.0010 to 0.0024 in.)

    Maximum oil clearance (Cylinder head RH):
    Item
    Specified Condition
    No. 1 (Intake)
    0.07 mm (0.0028 in.)
    Others
    0.10 mm (0.0039 in.)

    Maximum oil clearance (Cylinder head LH):
    0.10 mm (0.0039 in.)

    If the oil clearance is greater than the maximum, replace the camshaft bearings and/or camshafts.
    If necessary, replace the camshaft bearing caps and cylinder head together.

    Reference:
    Item
    Specified Condition
    Cylinder head journal bore diameter
    40.009 to 40.017 mm (1.5752 to 1.5755 in.)
    Camshaft bearing center wall thickness (Mark "2")
    2.004 to 2.008 mm (0.0789 to 0.0791 in.)
    Camshaft journal diameter
    35.971 to 35.985 mm (1.4165 to 1.4167 in.)

  1. Remove the Plastigage completely.

  1. Remove the camshafts.

  1. Remove the camshaft bearing.



27. INSPECT CAMSHAFT THRUST CLEARANCE


A075624E01
  1. Install the camshafts. (Click here or Click here).

  1. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard thrust clearance:
    0.04 to 0.09 mm (0.016 to 0.035 in.)

    Maximum thrust clearance:
    0.11 mm (0.0043 in.)

    If the thrust clearance is greater than the maximum, replace the camshafts.
    If necessary, replace the camshaft bearing caps and cylinder head as a set.



28. INSPECT CONNECTING ROD THRUST CLEARANCE


A075147E01
  1. Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.15 to 0.30 mm (0.0059 to 0.0118 in.)

    Maximum thrust clearance:
    0.35 mm (0.0138 in.)



29. INSPECT CONNECTING ROD OIL CLEARANCE
  1. Check the matchmarks on the connecting rod and cap are aligned to ensure correct assembly.

  1. Remove the 2 connecting rod cap bolts.

  1. Clean the crank pin, bearing and connecting rod.

  1. Check the crank pin and bearing for any pits and scratches.



    A075148E02
  1. Lay a strip of plastigage across the crank pin.



    A075149E02
  1. Check that the protrusion of the connecting rod cap is facing in the correct direction.

  1. Apply a light coat of engine oil to the threads of the connecting rod cap bolts.



    A075150E01
  1. Tighten the bolts alternately to the specified torque.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



    A075151E03
  1. Mark the front side of the each connecting cap bolt with paint.

  1. Retighten the cap bolts 90° as shown in the illustration.

    NOTICE:
    Do not turn the crankshaft.

  1. Remove the 2 bolts, connecting rod cap and lower bearing.



    A075152E02
  1. Measure the plastigage at its widest point.

    Standard oil clearance:
    0.026 to 0.046 mm (0.0010 to 0.0018 in.)

    Maximum oil clearance:
    0.066 mm (0.0025 in.)

    NOTICE:
    Completely remove the plastigage.



    A075153E02
  1. When replacing the bearing, replace it with one with the same number as marked on the connecting rod. There are 4 sizes of standard bearings, marked "1 ", "2", "3" and "4" accordingly.

    HINT:
    Standard bearing center wall thickness

    Mark
    mm (in.)
    "1"
    1.484 to 1.487 (0.0584 to 0.0585)
    "2"
    1.487 to 1.490 (0.0585 to 0.0587)
    "3"
    1.490 to 1.493 (0.0587 to 0.0588)
    "4"
    1.493 to 1.496 (0.0588 to 0.0589)



30. CHECK CYLINDER BLOCK FOR WARPAGE


A076052E01
  1. Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.

    Maximum warpage:
    0.05 mm (0.0020 in.)

    If the warpage is greater than the maximum, replace the cylinder block.



31. INSPECT CYLINDER BORE


A092877E02
  1. Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.

    Standard diameter:
    94.000 to 94.012 mm (3.7008 to 3.7013 in.)

    Maximum diameter:
    94.132mm (3.7060 in.)

    If the average diameter of 4 positions is greater than the maximum, replace the cylinder block.



32. INSPECT WITH PISTON SUB-ASSEMBLY


A076054E01
  1. Using a micrometer, measure the piston diameter at right angles to the piston pin center line, 27.7 mm (1.091 in.) from the piston head.

    Piston diameter:
    93.910 to 93.940 mm (3.6972 to 3.6984 in.)



33. INSPECT PISTON OIL CLEARANCE
  1. Subtract the piston diameter measurement from the cylinder bore diameter measurement.

    Standard oil clearance:
    0.060 to 0.102 mm (0.0031 to 0.0040 in.)

    Maximum oil clearance:
    0.13 mm (0.0051 in.)

    If the oil clearance is greater than the maximum, replace all the 6 pistons. If necessary, replace the cylinder block.



34. INSPECT CONNECTING ROD SUB-ASSEMBLY


Z000064E01


  1. Using a rod aligner and feeler gauge, check the connecting rod alignment.

    1. Check for misalignment.

      Maximum misalignment:
      0.05 mm (0.0020 in.) per 100 mm (3.94 in.)

      If misalignment is greater than the maximum, replace the connecting rod assembly.



    2. Z000065E01
    3. Check the twist.

      Maximum twist:
      0.15 mm (0.0059 in.) per 100 mm (3.94 in.)

      If the twist is greater than the maximum, replace the connecting rod assembly.



35. INSPECT PISTON PIN OIL CLEARANCE


A013490E01
  1. Using a caliper gauge, measure the internal diameter of the piston pin hole.

    Piston pin hole internal diameter:
    22.001 to 22.010 mm (0.8662 to 0.8665 in.)

    Piston pin hole inside diameter:
    Mark
    mm (in.)
    A
    22.001 to 22.004 (0.8662 to 0.8663)
    B
    22.005 to 22.007 (0.8663 to 0.8664)
    C
    22.008 to 22.010 (0.8665 to 0.8665)



    EM00227E01
  1. Using a micrometer, measure the piston pin diameter.

    Piston pin diameter:
    21.997 to 22.006 mm (0.8660 to 0.8664 in.)

    Piston pin diameter:
    Mark
    mm (in.)
    A
    21.997 to 22.000 (0.8660 to 0.8661)
    B
    22.001 to 22.003 (0.8661 to 0.8663)
    C
    22.004 to 22.006 (0.8663 to 0.8664)



    A076055E01
  1. Using a caliper gauge, measure the internal diameter of the connecting rod bushing.

    Bushing internal diameter:
    22.005 to 22.014 mm (0.8663 to 0.8667 in.)

    Bushing internal diameter:
    Mark
    mm (in.)
    A
    22.005 to 22.008 (0.8663 to 0.8665)
    B
    22.009 to 22.011 (0.8665 to 0.8666)
    C
    22.012 to 22.014 (0.8666 to 0.8667)

  1. Subtract the piston pin diameter measurement from the piton pin hole diameter measurement.

    Standard oil clearance:
    0.001 to 0.007 mm (0.00004 to 0.00028 in.)

    Maximum oil clearance:
    0.040 mm (0.0016 in.)



    A076391E02
  1. If the oil clearance is greater than the maximum, replace the bushing. If necessary, replace the piston and piston pin together.

  1. Subtract the piston pin diameter measurement from the bushing inside diameter measurement.

    Standard oil clearance:
    0.005 to 0.011 mm (0.0002 to 0.0004 in.)

    Maximum oil clearance:
    0.050 mm (0.0020 in.)

  1. If the oil clearance is greater than the maximum, replace the bushing. If necessary, replace the connecting rod and piston pin together.



36. INSPECT RING GROOVE CLEARANCE


A076056E01
  1. Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

    Ring groove clearance:
    No.1 0.02 to 0.07 mm (0.0008 to 0.0028 in.)
    No.2 0.02 to 0.06 mm (0.0008 to 0.0024 in.)
    Oil 0.07 to 0.15 mm (0.0028 to 0.0060 in.)



37. INSPECT PISTON RING END GAP


A076057E02
  1. Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.



    A037355E01
  1. Using a feeler gauge, measure the end gap.

    Standard end gap:
    No. 1 0.30 to 0.40 mm (0.0118 to 0.0157 in.)
    No. 2 0.40 to 0.50 mm (0.0157 to 0.0197 in.)
    Oil (Side rail) 0.10 to 0.40 mm (0.0039 to 0.0157 in.)

    Maximum end gap:
    No. 1 1.0 mm (0.039 in.)
    No. 2 1.1 mm (0.043 in.)
    Oil (Side rail) 1.0 mm (0.039 in.)



38. INSPECT CONNECTING ROD BOLT


A015065E01
  1. Using vernier calipers, measure the tension portion diameter of the bolt.

    Standard diameter:
    7.2 to 7.3 mm (0.283 to 0.287 in.)

    Minimum diameter:
    7.0 mm (0.276 in.)

    If the diameter is less than the minimum, replace the bolt.



39. INSPECT CRANKSHAFT BEARING CAP SET BOLT


A015065E01
  1. Using vernier calipers, measure the tension portion diameter of the bolt.

    Standard diameter:
    10.0 to 10.2 mm (0.393 to 0.402 in.)

    If the diameter is less than the minimum, replace the bolt.



40. INSPECT CRANKSHAFT


A076058E01
  1. Using a dial indicator and V-blocks, measure the runout as shown in the illustration.

    Maximum circle runout:
    0.06 mm (0.0024 in.)



    A076059E01
  1. Using a micrometer, measure the diameter of each main journal.

    Diameter:
    71.988 to 72.000 mm (2.8342 to 2.8346 in.)

  1. Check each main journal for taper and out-of-roundness as shown.

    Maximum taper and out-of-roundness:
    0.02 mm (0.0008 in.)



    A076060E01
  1. Using a micrometer, measure the diameter of each crank pin.

    Diameter:
    55.992 to 56.000 mm (2.2044 to 2.2047 in.)

  1. Check each crank pin for taper and out-of-roundness as shown.

    Maximum taper and out-of-roundness:
    0.02 mm (0.0008 in.)



41. INSPECT CRANKSHAFT OIL CLEARANCE


A076063E06

HINT:
There are 2 types of main bearings with different widths (19.0 mm (0.748 in.) and 22.4 mm (0.882 in.)) for use in the inspection. Install the 22.4mm (0.882 in.) bearings in the No. 1 and No. 4 cylinder block journal positions with the main bearing cap. Install the 19.0 mm (0.748 in.) bearings in the No. 2 and No. 3 positions.

  1. Clean each main journal and bearing.



    A094746E02
  1. Install the 4 upper bearings.

    1. Install the upper bearing near the center of the cylinder block.

      NOTICE:
      1. The width of the No. 1 and No. 4 journal bearings is different from that of the No. 2 and No. 3 journal bearings. Therefore, confirm whether it is the correct journal bearing prior to installation.
      2. Do not apply engine oil to the bearing installation surfaces of the cylinder block and the back side of the bearings.
      3. Check that the oil groove on the cylinder block can be seen through the oil supply holes of the upper bearing.



    A076065E01
  1. Install the 4 lower bearings.

    1. Install the lower bearing near the center of the cylinder block.

      NOTICE:
      Do not apply engine oil to the bearing and its contact surface.

      HINT:
      A number marked on each main bearing cap indicates the installation position.

  1. Place the crankshaft on the cylinder block.



    A076066E02
  1. Lay a strip of plastigage across each journal.



    A076067E01
  1. Examine the front marks and numbers, check the sequence order is as shown and install the bearing caps onto the cylinder block.

  1. Apply a light coat of engine oil to the threads of bearing cap bolts.

  1. Temporarily install the 8 main bearing cap bolts in the inside positions.



    A076069E02
  1. Install the main bearing caps. Tighten the 2 bolts for each bearing cap until the clearance between the bearing cap and the cylinder block is under 6 mm (0.23 in.).



    A076070E01
  1. Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.

  1. Apply a light coat of engine oil to the threads of main bearing cap bolts.



    A076071E04
  1. Install the 16 main bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

    Torque:
    61 N*m{ 622 kgf*cm , 45 ft.*lbf }



    A076072E03
  1. Mark the front side of the bearing cap bolts with paint.

  1. Retighten the bearing cap bolts 90° in the sequence as shown.

  1. Check that the painted mark is now at a 90° angle from the front.

    NOTICE:
    Do not turn the crankshaft.



    A075843E03
  1. Install the 8 main bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Remove the main bearing caps.



    A075844E01
  1. Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.018 to 0.030 mm (0.0007 to 0.0012 in.)

    Maximum clearance:
    0.046 mm (0.0018 in.)

    If the oil clearance is greater than the maximum, replace the bearings. If necessary, replace the crankshaft.

    NOTICE:
    Completely remove the plastigage.



    A075845E03
  1. Replace the bearing with the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then refer to the table below for the appropriate bearing number. There are 5 size of standard bearings, marked "1", "2", "3", "4" and "5" accordingly.
    Journal bearing 
    Cylinder block (A) + Crankshaft
    0 -
    6 - 1
    12 - 7
    18 - 23
    24 - 28
    Use Bearing
    "1"
    "2"
    "3"
    "4"
    "5"

    HINT:
    EXAMPLE
    Cylinder block "11" (A) + Crankshaft "06" (B)
    =Total number 17 (Use bearing "3")


    Item
    Mark
    mm (in.)
    Cylinder block main journal bore diameter (A)
    "00"
    "01"
    "02"
    "03"
    "04"
    "05"
    "06"
    "07"
    "08"
    "09"
    "10"
    "11"
    "12"
    "13"
    "14"
    "15"
    "16"
    77.000 (3.0315)
    77.001 (3.0315)
    77.002 (3.0316)
    77.003 (3.0316)
    77.004 (3.0317)
    77.005 (3.0317)
    77.006 (3.0317)
    77.007 (3.0318)
    77.008 (3.0318)
    77.009 (3.0319)
    77.010 (3.0319)
    77.011 (3.0319)
    77.012 (3.0320)
    77.013 (3.0320)
    77.014 (3.0320)
    77.015 (3.0321)
    77.016 (3.0321)
    Crankshaft main journal diameter (B)
    "00"
    "01"
    "02"
    "03"
    "04"
    "05"
    "06"
    "07"
    "08"
    "09"
    "10"
    "11"
    71.999 to 72.000 (2.8346 to 2.8346)
    71.998 to 71.999 (2.8346 to 2.8346)
    71.997 to 71.998 (2.8345 to 2.8346)
    71.996 to 71.997 (2.8345 to 2.8346)
    71.995 to 71.996 (2.8344 to 2.8345)
    71.994 to 71.995 (2.8344 to 2.8344)
    71.993 to 71.994 (2.8343 to 2.8344)
    71.992 to 71.993 (2.8343 to 2.8343)
    71.991 to 71.992 (2.8343 to 2.8343)
    71.990 to 71.991 (2.8343 to 2.8343)
    71.989 to 71.990 (2.8342 to 2.8343)
    71.988 to 71.989 (2.8342 to 2.8342)
    Standard bearing center wall thickness
    "1"
    "2"
    "3"
    "4"
    "5"
    2.488 to 2.491 (0.0980 to 0.0981)
    2.491 to 2.494 (0.0981 to 0.0982)
    2.494 to 2.497 (0.0982 to 0.0983)
    2.497 to 2.500 (0.0982 to 0.0984)
    2.500 to 2.503 (0.0984 to 0.0985)