Home › ENGINE · 1GR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here


HINT:
  1. Thoroughly clean all parts to be assembled.
  2. Before installing the parts, apply new engine oil to all sliding and rotating surfaces.
  3. Replace all gaskets, O-rings and oil seals with new parts.



1. REMOVE ENGINE HANGERS


A072941E02
  1. Remove the 2 bolts and engine hanger No. 1.

  1. Remove the 2 bolts and engine hanger No. 2.



2. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the bolt, then pull out the oil level gauge guide.

  1. Remove the O-ring from the oil level gauge guide.



3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
  1. Remove the 2 water drain cocks.



4. REMOVE VVT SENSOR


G036794E01
  1. Remove the 2 bolts, then remove the 2 VVT sensors.



5. REMOVE CRANKSHAFT POSITION SENSOR


G036795E01
  1. Remove the bolt, then remove the crankshaft position sensor.



6. REMOVE OIL CONTROL VALVE FILTER


A072942E02
  1. Remove the plug and filter, then remove the gasket from each cylinder head.



7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


A072943E01
  1. Remove the 10 bolts, 3 seal washers and 2 nuts, then remove the cylinder head cover.

  1. Remove the gasket from the cylinder head cover.



8. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


A072944E01
  1. Remove the 10 bolts, 3 seal washers and 2 nuts, then remove the cylinder head cover.

  1. Remove the gasket from the cylinder head cover.

  1. Remove the ventilation valve from the cylinder head cover.



9. REMOVE CRANKSHAFT PULLEY


A072945E01
  1. Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.



    G036831E01
  1. Check that each timing mark of the camshaft timing gears is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.



    A072947E02
  1. Using SST, fix the pulley and loosen the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)



10. REMOVE OIL PAN DRAIN PLUG
  1. Remove the drain plug and gasket.



11. REMOVE NO.2 OIL PAN SUB-ASSEMBLY


    G036799E01
  1. Remove the 15 bolts and 2 nuts (for 2WD).



    A118006E01
  1. Remove the 10 bolts and 2 nuts (for Pre Runner and 4WD).



    A072950E03
  1. Insert the blade of the oil pan seal cutter between the oil pan and oil pan No. 2, then cut off applied sealer and remove the oil pan No. 2.

    NOTICE:
    1. Be careful not to damage the contact surface of the oil pan and oil pan No. 2.
    2. Be careful not to damage the oil pan No. 2 flange.



12. REMOVE OIL STRAINER SUB-ASSEMBLY


G036832E01
  1. Remove the 2 nuts, then remove the oil strainer and gasket (for 2WD).



    A072951E02
  1. Remove the 2 nuts, then remove the oil strainer and gasket (for Pre Runner and 4WD).



13. REMOVE OIL PAN SUB-ASSEMBLY


G036798E02
  1. Remove the 17 bolts and 2 nuts (for 2WD).



    A122289E01
  1. Remove the 17 bolts and 2 nuts (for Pre Runner and 4WD).



    G036806E01
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block in the sequence shown.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. Remove the O-ring from the oil pump.



14. REMOVE WATER PUMP ASSEMBLY


A072954E01
  1. Remove the 17 bolts, then remove the water pump and gasket.



15. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


G036855E03
  1. Remove the 15 bolts and 2 nuts.



    G036859E01
  1. Remove the timing chain cover by prying between the timing chain cover, cylinder head and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the LH cylinder head.



16. REMOVE NO.1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.



    A072958E02
  1. While turning the stopper plate of the tensioner upward, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner downward, insert a bar of φ 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts, then remove the chain tensioner.



17. REMOVE CHAIN TENSIONER SLIPPER


18. REMOVE IDLE SPROCKET ASSEMBLY


G036860E01
  1. Using a 10 mm hexagon wrench, remove the idle gear shaft No. 2, idle gear No. 1 and idle gear shaft No. 1.



19. REMOVE NO.2 CHAIN VIBRATION DAMPER


G036844E01
  1. Remove the 2 chain vibration dampers No. 2.



20. REMOVE CHAIN SUB-ASSEMBLY


21. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET


22. REMOVE NO.1 CHAIN VIBRATION DAMPER


G036808E01
  1. Remove the 2 bolts, then remove the chain vibration damper No. 1.



23. REMOVE CAMSHAFT TIMING GEARS AND NO.2 CHAIN (for Bank 1)


G036850E01
  1. While raising the chain tensioner No. 2 upward, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.



    G036834E01
  1. Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing gear assembly and timing chain No. 2.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.



24. REMOVE NO.2 CHAIN TENSIONER ASSEMBLY


A072962E01
  1. Remove the bolt, then remove the chain tensioner No. 2.



25. REMOVE CAMSHAFT TIMING GEARS AND NO.2 CHAIN (for Bank 2)


G036835E01
  1. While pushing down the chain tensioner No. 3, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.



    G036836E01
  1. Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing gear assembly and timing chain No. 2.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.



26. REMOVE NO.3 CHAIN TENSIONER ASSEMBLY


A072965E01
  1. Remove the bolt, then remove the chain tensioner No. 3.



27. REMOVE CAMSHAFTS

NOTICE:
Keep the camshaft level while it is being removed. The camshaft thrust clearance is very small and failing to keep it level could crack or damage the cylinder head journal surface, which receives the thrust. This could subsequently lead the camshaft to seize or break. Perform the following steps to avoid such problems.



    A072966E02
  1. Remove the camshafts of the RH bank.

    1. Rotate the camshafts counterclockwise using a wrench so that cam lobes of No. 1 cylinder face in the directions as shown in the illustration.



    2. A072967E07
    3. Using several steps, uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

    4. Remove the 8 bearing caps, then remove the 2 camshafts.



    A072968E06
  1. Remove the camshafts of the LH bank.

    1. Using several steps, uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

    2. Remove the 8 bearing caps, then remove the 2 camshafts.



28. REMOVE NO.1 CAMSHAFT BEARING


29. REMOVE NO.2 CAMSHAFT BEARING


30. REMOVE CYLINDER HEADS


A072969E04
  1. Using several steps, remove the 2 cylinder head bolts on the LH cylinder head in the sequence shown in the illustration.



    A072970E03
  1. Using several steps, loosen the 8 cylinder head bolts on each cylinder head with a 10 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 16 cylinder head bolts, then remove the plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing the bolts in the wrong order.



    A072971E01
  1. Lift the cylinder head from the dowels on the cylinder block, and place the 2 cylinder heads on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to remove, pry between the cylinder head and cylinder block with a screwdriver.

  1. Remove the RH and LH cylinder head gaskets.



31. REMOVE NO.1 WATER OUTLET PIPE


G036807E01
  1. Separate the knock sensor wire.

  1. Remove the 3 bolts, then remove the water outlet pipe.



32. REMOVE KNOCK CONTROL SENSOR


A076270E01
  1. Disconnect the knock sensor connectors.

  1. Remove the 2 bolts, then remove the 2 knock sensors.



33. REMOVE REAR ENGINE OIL SEAL RETAINER


A076247E02
  1. Remove the 5 bolts and 2 nuts.

  1. Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.



34. REMOVE VALVE LIFTER


A075601E01

HINT:
Arrange the valve lifter in the correct order.



35. REMOVE VALVE


A075602E02

HINT:
Arrange the valves, inner compression springs, valve spring retainers and valve spring retainer rocks in the correct order.

  1. Place the cylinder head on a wooden block.

  1. Using SST, compress the inner compression spring and remove the 2 valve spring retainer rocks.

    SST
    09202-70020   (09202-00010)

  1. Remove the valve, inner compression spring and valve spring retainer.



36. REMOVE VALVE SPRING SEAT


A075603E01
  1. Using compressed air and a magnetic finger, remove the valve spring seat by blowing air.



37. REMOVE VALVE STEM OIL O SEAL OR RING


A075604E01
  1. Using needle-nose pliers, remove the valve stem oil seal.



38. CLEAN CYLINDER HEAD SUB-ASSEMBLY


A075605E01
  1. Using a gasket scraper, remove all the gasket material from the cylinder block contact surface.

    NOTICE:
    Be careful not to scratch the cylinder block contact surface.



    A075606E01
  1. Using a wire brush, remove all the carbon from the combustion chambers.

    NOTICE:
    Be careful not to scratch the combustion chambers.



    A075607E01
  1. Using a valve guide bushing brush and solvent, clean all the valve guide bushes.



    A075608E01
  1. Using a soft brush and solvent, thoroughly clean the cylinder head.



39. REMOVE WITH PISTON SUB-ASSEMBLY WITH CONNECTING ROD


A076043E01
  1. Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push in the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearings, connecting rod and cap together.
    2. Arrange the piston and connecting rod in the correct order.



40. REMOVE CONNECTING ROD BEARING


41. REMOVE PISTON RING SET


A076044E01
  1. Using a piston ring expander, remove the 2 compression rings.

  1. Remove the 2 side rails and oil ring by hand.



42. REMOVE HOLE SNAP RING


P012403E01
  1. Using a small screwdriver, pry out the 2 snap rings.



43. REMOVE WITH PISTON SUB-ASSEMBLY


A076045E06
  1. Gradually heat the piston to approximately 80°C (176°F).



    A076046E01
  1. Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.



44. INSPECT CRANKSHAFT THRUST CLEARANCE


A076047E01
  1. Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.04 to 0.24 mm (0.0016 to 0.0094 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is greater than the maximum, replace the pair of the thrust washers or crankshaft.

    HINT:
    Thrust washer thickness:
    1.93 to 1.98 mm (0.0760 to 0.0780 in.)



45. REMOVE CRANKSHAFT


A076048E01
  1. Using several steps, uniformly loosen and remove the 8 main bearing cap bolts and seal washers in the sequence shown in the illustration.



    A076049E01
  1. Using several steps, uniformly loosen and remove the 16 main bearing cap bolts in the sequence shown in the illustration.



    A121032E01
  1. Using a screwdriver, pry out the main bearing caps. Remove the 4 main bearing caps and lower bearings.

    NOTICE:
    1. Pull up the main bearing cap by turning it to the right and left little by little.
    2. Be careful not to damage the joint surfaces of the cylinder block and the main bearing cap.



46. REMOVE CRANKSHAFT THRUST WASHER SET


47. REMOVE CRANKSHAFT BEARING


48. REMOVE NO.1 SUB-ASSEMBLY OIL NOZZLE


A076051E01
  1. Using a 5 mm socket hexagon wrench, remove the 3 oil nozzles.