ENGINE UNIT > INSPECTION |
| 1. INSPECT CHAIN SUB-ASSEMBLY |
![]() |
Pull the chain with a force of 147 N (15 kgf, 33 Ibf) as shown in the illustration.
Using vernier calipers, measure the length of 16 links.
| 2. INSPECT NO.2 CHAIN SUB-ASSEMBLY |
![]() |
Pull the chain with a force of 147 N (15 kgf, 33 Ibf) as shown in the illustration.
Using vernier calipers, measure the length of 16 links.
| 3. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
| 4. INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate downward to release the lock. Push the plunger and check that it moves smoothly.
| 5. INSPECT CAMSHAFT TIMING GEAR OR SPROCKET |
![]() |
Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.
Wrap the chain around the sprocket.
Using vernier calipers, measure the sprocket diameter with the chain.
| 6. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Measure the distance between the most worn out timing gear tip and the beginning of the worn area below the tip.
Wrap the chain around the timing gear.
Using vernier calipers, measure the sprocket diameter with the chain.
| 7. INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET |
![]() |
Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.
Wrap the chain around the drive sprocket.
Using vernier calipers, measure the sprocket diameter with the chain.
| 8. INSPECT CHAIN TENSIONER SLIPPER |
![]() |
Using vernier calipers, measure the tensioner slipper wear.
| 9. INSPECT NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Using vernier calipers, measure the vibration damper wear.
| 10. INSPECT TIMING CHAIN GUIDE |
![]() |
Using vernier calipers, measure the chain guide wear.
| 11. INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET |
![]() |
Wrap the chain around the sprocket.
Using vernier calipers, measure the sprocket diameter with the chain.
| 12. INSPECT BALANCESHAFT DRIVE GEAR SUB-ASSEMBLY |
![]() |
Wrap the chain around the sprocket.
Using vernier calipers, measure the sprocket diameter with the chain.
| 13. INSPECT NO. 2 CHAIN VIBRATION DAMPER |
![]() |
Using vernier calipers, measure the vibration damper No.2 wear.
| 14. INSPECT NO. 3 CHAIN VIBRATION DAMPER |
![]() |
Using vernier calipers, measure the vibration damper No.3 wear.
| 15. INSPECT NO. 4 CHAIN VIBRATION DAMPER |
![]() |
Using vernier calipers, measure the vibration damper No.4 wear.
| 16. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using vernier calipers, measure the minimum diameter of the elongated thread at the measuring point.
| 17. INSTALL CRANKSHAFT PULLEY SET CRANKSHAFT KEY |
![]() |
Install the 2 pulley keys to the crankshaft.
| 18. INSTALL NO. 4 CHAIN VIBRATION DAMPER |
![]() |
Install the vibration damper No.4 with the 2 bolts.
| 19. INSPECT VALVE LASH ADJUSTER ASSEMBLY |
![]() |
Place the lash adjuster into a container full of engine oil.
Insert SST's tip into the lash adjuster's plunger and use the tip to press down on the checkball inside the plunger.
Squeeze the SST and lash adjuster together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed the air.
After bleeding the air, remove the SST. Then quickly and firmly press the plunger with a finger.
| 20. INSPECT CYLINDER HEAD FOR FLATNESS |
![]() |
Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of contacting the cylinder block and manifolds.
| 21. INSPECT CYLINDER HEAD FOR CRACKS |
![]() |
Using a dye penetrate, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head.
| 22. INSPECT INTAKE VALVE SEAT |
![]() |
Apply a light coat of prussian blue (or white lead) to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve seat by using the following procedure.
If prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts in the middle of the valve face with the width between 1.0 and 1.4 mm (0.039 and 0.055 in.).
| 23. INSPECT EXHAUST VALVE SEAT |
![]() |
Apply a light coat of prussian blue (or white lead) to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve seat by using to the following procedure.
If prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts in the middle of the valve face with the width between 1.0 and 1.4 mm (0.039 and 0.055 in.).
| 24. INSPECT CAMSHAFT |
![]() |
Check the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Using a micrometer, measure the cam lobe height.
![]() |
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
| No.1 journal | 35.949 to 35.965 mm (1.4153 to 1.4159 in.) |
| Other journal | 26.959 to 26.975 mm (1.0614 to 1.0620 in.) |
| 25. INSPECT NO.2 CAMSHAFT |
![]() |
Check the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Using a micrometer, measure the cam lobe height.
![]() |
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
| No.1 journal | 35.949 to 35.965 mm (1.4153 to 1.4159 in.) |
| Other journal | 26.959 to 26.975 mm (1.0614 to 1.0620 in.) |
| 26. INSPECT CAMSHAFT THRUST CLEARANCE |
![]() |
Install the camshafts.
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 27. INSPECT CAMSHAFT OIL CLEARANCE |
![]() |
Clean the bearing caps and camshaft journals.
Place the camshafts on the cylinder head.
Lay a strip of Plastigage across each of the camshaft journals.
Install the bearing caps.
Remove the bearing caps.
![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| No.1 journal | 0.035 to 0.072 mm (0.0014 to 0.0029 in.) |
| Other journal | 0.025 to 0.062 mm (0.00098 to 0.0024 in.) |
Completely remove the Plastigage.
| 28. INSPECT INNER COMPRESSION SPRING |
![]() |
Using vernier calipers, measure the free length of the inner compression spring.
![]() |
Using a steel square, measure the deviation of the inner compression spring.
| 29. INSPECT INTAKE VALVE |
![]() |
Using vernier calipers, measure the valve's overall length.
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using vernier calipers, measure the valve head margin thickness.
| 30. INSPECT EXHAUST VALVE |
![]() |
Using vernier calipers, measure the valve's overall length.
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using vernier calipers, measure the valve head margin thickness.
| 31. INSPECT VALVE GUIDE BUSHING |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| 32. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 33. INSPECT CONNECTING ROD OIL CLEARANCE |
Check that the matchmarks on the connecting rod and cap are aligned to ensure the correct reassembly.
![]() |
Remove the 2 connecting rod cap bolts.
Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches.
![]() |
Lay a strip of Plastigage on the crank pin.
![]() |
Check that the front mark of the connecting rod cap is facing forward.
![]() |
Install the connecting rod cap.
Remove the 2 bolts and connecting rod cap (see steps (b) and (c) above).
![]() |
Measure the Plastigage at its widest point.
| Mark | Thickness |
| 4 | 52.989 to 53.002 mm (2.0862 to 2.0867 in.) |
| 5 | 52.989 to 53.002 mm (2.0862 to 2.0867 in.) |
| 6 | 52.989 to 53.002 mm (2.0862 to 2.0867 in.) |
| Mark | Thickness |
| 4 | 1.484 to 1.487 mm (0.0584 to 0.0585 in.) |
| 5 | 1.488 to 1.490 mm (0.0586 to 0.0587 in.) |
| 6 | 1.491 to 1.493 mm (0.0587 to 0.0588 in.) |
Completely remove the Plastigage.
| 34. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| 35. CLEAN WITH PIN PISTON SUB-ASSEMBLY |
![]() |
Using a gasket scraper, remove the carbon from the piston top.
![]() |
Using a groove cleaning tool or broken ring, clean the piston ring grooves.
![]() |
Using solvent and a brush, thoroughly clean the piston.
| 36. INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY |
Check the oil nozzles for damage or clogging.
If necessary, replace the oil nozzle.
| 37. INSPECT BALANCE SHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the balanceshaft back and forth.
| 38. INSPECT CYLINDER BLOCK FOR FLATNESS |
![]() |
Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.
![]() |
Visually check the cylinder for vertical scratches.
If deep scratches are present, rebore all the 4 cylinders. If necessary, replace the cylinder block.
| 39. INSPECT CYLINDER BORE |
![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions A in the thrust and axial directions.
![]() |
Inspect the cylinder ridge.
If the wear is less than 0.2 mm (0.008 in.), using a ridge reamer, grind the top of the cylinder.
| 40. CLEAN CYLINDER BLOCK |
![]() |
Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.
Using a soft brush and solvent, thoroughly clean the cylinder block.
| 41. INSPECT PISTON DIAMETER |
![]() |
Using a micrometer, measure the piston diameter at right angles to the piston center line, the indicated distance from the piston end.
| 42. INSPECT PISTON OIL CLEARANCE |
Measure the cylinder bore diameter in the thrust directions (see step 20).
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
If the oil clearance is greater than the standard.
Prepare 4 new O/S pistons.
Using a micrometer, measure the piston diameter at right angles to the piston center line, the indicated distance from the piston end.
Calculate the amount each cylinder is to be rebored as follows:
| P | Piston diameter |
| C | Piston clearance: 0.019 to 0.052 mm (0.0007 to 0.0020 in.) |
| H | Allowance for honing: 0.02 mm (0.0008 in.) or less |
Bore and hone the cylinders to calculated dimensions.
| 43. INSPECT RING GROOVE CLEARANCE |
![]() |
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
| Item | Specified Condition |
| No. 1 | 0.020 to 0.075 mm (0.0008 to 0.0030 in.) |
| No. 2 | 0.020 to 0.065 mm (0.0008 to 0.0026 in.) |
| Oil | 0.020 to 0.070 mm (0.0008 to 0.0028 in.) |
| 44. INSPECT PISTON RING END GAP |
![]() |
Insert the piston ring into the cylinder bore.
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.
![]() |
Using a feeler gauge, measure the end gap.
| Item | Specified Condition |
| No. 1 | 0.22 to 0.34 mm (0.0087 to 0.0134 in.) |
| No. 2 | 0.45 to 0.57 mm (0.0177 to 0.0224 in.) |
| Oil | 0.10 to 0.40 mm (0.0039 to 0.0157 in.) |
| Item | Specified Condition |
| No. 1 | 0.90 mm (0.0354 in.) |
| No. 2 | 1.36 mm (0.0535 in.) |
| Oil | 0.75 mm (0.0295 in.) |
| 45. INSPECT PISTON PIN OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the piston pin hole.
![]() |
Using a micrometer, measure the piston pin diameter.
![]() |
Using a caliper gauge, measure the inside diameter of the connecting rod bushing.
Subtract the piston pin diameter measurement from the piton pin hole diameter measurement.
![]() |
Subtract the piston pin diameter measurement from the bushing inside diameter measurement.
If the oil clearance is greater than the maximum, replace the bushing. If necessary, replace the connecting rod and piston pin as a set.
| 46. INSPECT CONNECTING ROD |
![]() |
Using a rod aligner and feeler gauge, check the connecting rod alignment.
Check for bend.
![]() |
Check for twist.
| 47. INSPECT CONNECTING ROD BOLT |
![]() |
Using vernier calipers, measure the tension portion diameter of the bolt.
| 48. INSPECT CRANKSHAFT |
![]() |
Inspect for circle runout.
Place the crankshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Inspect the main journals.
Using a micrometer, measure the diameter of each main journal.
| Item | Specified Condition |
| No.3 journal | 59.981 to 59.994 mm (2.3615 to 2.3620 in.) |
| Except No.3 journal | 59.987 to 60.000 mm (2.3619 to 2.3622 in.) |
Check each main journal for taper and out-of-round as shown in the illustration.
![]() |
Inspect the crank pin.
Using a micrometer, measure the diameter of each crank pin.
Check each crank pin for taper and out-of-round as shown in the illustration.
| 49. INSPECT CRANKSHAFT OIL CLEARANCE |
Clean each main journal and bearing.
Check each main journal and bearing for pitting and scratches.
If the journal or bearing is damaged, replace the bearing.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of Plastigage across each journal.
![]() |
Install the 5 crankshaft bearing caps in their proper locations.
Install the 5 crankshaft bearing caps with the 10 bolts (see step 49).
Remove the 10 bolts and 5 crankshaft bearing caps.
![]() |
Measure the Plastigage at its widest point.
| Bearing Cap | Standard |
| No.3 | 0.030 to 0.055 mm (0.0012 to 0.0022 in.) |
| Others | 0.024 to 0.049 mm (0.0009 to 0.0019 in.) |
| Mark | Diameter |
| 1 | 64.004 to 64.010 mm (2.5198 to 2.5201 in.) |
| 2 | 64.011 to 64.016 mm (2.5201 to 2.5203 in.) |
| 3 | 64.017 to 64.022 mm (2.5203 to 2.5206 in.) |
| Mark | Thickness |
| 1 | 1.987 to 1.990 mm (0.0782 to 0.0783 in.) |
| 2 | 1.991 to 1.993 mm (0.0784 to 0.0785 in.) |
| 3 | 1.994 to 1.996 mm (0.0785 to 0.0786 in.) |
Completely remove the Plastigage.
| 50. INSPECT CRANKSHAFT BEARING CAP SET BOLT |
![]() |
Using vernier calipers, measure the minimum diameter of the compressed thread at the measuring point.
| 51. INSPECT NO.1 BALANCESHAFT |
![]() |
Inspect the diameter of the journal.
Using a micrometer, measure the diameter of the balanceshaft main journals.
| Item | Specified Condition |
| A | 37.969 to 37.985 mm (1.4948 to 1.4955 in.) |
| B | 37.449 to 37.465 mm (1.4744 to 1.4750 in.) |
![]() |
Inspect the diameter of bearing.
Using a cylinder gauge, measure the inside diameter of the balanceshaft bearing.
| Item | Specified Condition |
| A | 38.025 to 38.045 mm (1.4970 to 1.4978 in.) |
| B | 37.525 to 37.545 mm (1.4774 to 1.4781 in.) |
Inspect oil clearance.
Subtract the balanceshaft main journal diameter measurement from the balanceshaft bearing inside diameter measurement.
| Item | Specified Condition |
| A | 0.040 to 0.076 mm (0.0016 to 0.0030 in.) |
| B | 0.060 to 0.096 mm (0.0024 to 0.0038 in.) |
| 52. INSPECT NO.2 BALANCESHAFT |
![]() |
Inspect the diameter of the journal.
Using a micrometer, measure the diameter of the balanceshaft main journals.
| Item | Specified Condition |
| A | 37.969 to 37.985 mm (1.4948 to 1.4955 in.) |
| B | 37.449 to 37.465 mm (1.4744 to 1.4750 in.) |
![]() |
Inspect the diameter of bearing.
Using a cylinder gauge, measure the inside diameter of the balanceshaft bearing.
| Item | Specified Condition |
| A | 38.025 to 38.045 mm (1.4970 to 1.4978 in.) |
| B | 37.525 to 37.545 mm (1.4774 to 1.4781 in.) |
Inspect oil clearance.
| Item | Specified Condition |
| A | 0.040 to 0.076 mm (0.0016 to 0.0030 in.) |
| B | 0.060 to 0.096 mm (0.0024 to 0.0038 in.) |