Home › ENGINE ยท 2TR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE OIL FILLER CAP SUB-ASSEMBLY


G037255E02
  1. Remove the oil filler cap sub-assembly.



2. REMOVE VENTILATION VALVE SUB-ASSEMBLY


G037256E01
  1. Remove the ventilation valve sub-assembly.



3. REMOVE CAMSHAFT POSITION SENSOR


G037258E02
  1. Remove the bolt and camshaft position sensor.



4. REMOVE CRANKSHAFT POSITION SENSOR


G037257E02
  1. Remove the bolt and crankshaft position sensor.



5. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


G037259E02
  1. Remove the bolt and camshaft timing oil control valve.



6. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


G037266E01
  1. Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.



7. REMOVE CRANKSHAFT PULLEY


G037261E05
  1. Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the bearing cap No.1, as shown in the illustration.



    G037262E01
  1. Using SST, loosen the crankshaft pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G037263E01
  1. Using SST, remove the crankshaft pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



8. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


G037265E01
  1. Remove the drain plug and gasket.

  1. Remove the 18 bolts and 2 nuts.



    G037267E01
  1. Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan sub-assembly No.2.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.



9. REMOVE OIL STRAINER SUB-ASSEMBLY


G037268E01
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.



10. REMOVE OIL PAN SUB-ASSEMBLY


G037269E02
  1. Remove the 16 bolts and 2 nuts.



    G037270E01
  1. Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.



    G037271E01
  1. Remove the O-ring.



11. REMOVE TIMING CHAIN COVER


G037272E02
  1. Remove the 19 bolts and 2 nuts as shown in the illustration.



    G037273E03
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.



    G037274E01
  1. Remove the 3 O-rings.



    G038407E01
  1. Using a 10 mm socket hexagon wrench, remove the timing chain cover plug.



12. REMOVE WATER PUMP ASSEMBLY


G037275E01
  1. Remove the 8 bolts, water pump and gasket.



13. REMOVE TIMING CHAIN GUIDE


G037278E04
  1. Remove the 2 bolts, timing chain guide and O-ring.



14. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


G037277E03

NOTICE:
  1. When the chain tensioner is removed, do not rotate the crankshaft.
  2. When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90 degrees to the right.

  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate's hole.



    G037279E01
  1. Remove the bolt, nut, chain tensioner assembly No.1 and gasket.



15. REMOVE CHAIN TENSIONER SLIPPER


G037281E04
  1. Remove the bolt and tensioner slipper.



16. REMOVE NO. 1 CHAIN VIBRATION DAMPER


G037280E01
  1. Remove the bolt, nut, and vibration damper.



17. REMOVE CHAIN SUB-ASSEMBLY
  1. Remove the chain.



18. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET


G037282E01
  1. Remove the crankshaft timing gear from the crankshaft.



19. REMOVE CAMSHAFT BEARING CAP


G037283E03
  1. Uniformly loosen and remove the 21 bearing cap bolts and 20 washers on the camshafts in the sequence shown in the illustration.



    G037284E05
  1. Remove the oil delivery pipe and O-ring from the bearing caps.



    G037285E02
  1. Remove the 9 bearing caps.



20. REMOVE CAMSHAFT


G037286E01
  1. Remove the camshaft sub-assembly.



21. REMOVE NO.2 CAMSHAFT


G037287E01
  1. Remove the No.2 camshaft sub-assembly.



22. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY


G037288E01
  1. Remove the 16 valve rocker arm sub-assembly.



23. REMOVE CAMSHAFT TIMING SPROCKET


G037291E01
  1. Fix the camshaft with a vise and then remove the sprocket bolt and camshaft timing sprocket.

    NOTICE:
    Be careful not to damage the camshaft.



24. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY


A062190E05
  1. Check the lock of the camshaft timing gear.

    1. Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.

      NOTICE:
      Be careful not to damage the camshaft.



  1. Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      2 advance side paths are provided in the groove of the camshaft. Plug one of the paths with a rubber piece.

    2. Break through the tape of the advance side path and the retard side path on the opposite side to the hole of the advance side path, as shown in the illustration.



    3. A062191E06
    4. Apply approximately 200 kPa (2.0 kgf*cm2, 28 psi) of air pressure to the two broken paths.

      CAUTION:
      Some oil splashing will occur. Cover the paths with a shop rag.



    5. A062192E06
    6. Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.

      OK:
      Gear rotates in the advance direction.

      HINT:
      This operation releases the lock pin for the most retarded position.

    7. When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path, in that order.

      NOTICE:
      Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Rotate the camshaft timing gear within its movable range several times, but do not turn it to the most retarded position. Check that the gear rotates smoothly.

      OK:
      Gear rotates in the advance direction.

      CAUTION:
      Do not use an air pressure to perform the smooth operation check.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing gear is locked at the most retarded position.



25. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY


G037292E01
  1. Remove the fringe bolt and camshaft timing gear.

    NOTICE:
    1. Be sure not to remove the other 3 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.



26. REMOVE CYLINDER HEAD SUB-ASSEMBLY


G037293E01
  1. Uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

  1. Remove the cylinder head.



27. REMOVE CYLINDER HEAD GASKET
  1. Remove the cylinder head and gasket.



28. REMOVE NO. 2 CHAIN VIBRATION DAMPER


G037294E04
  1. Move the stopper plate downward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate upward to set the lock, and insert a hexagon wrench into the stopper plate's hole.



    G037295E01
  1. Remove the bolt and chain vibration damper No.2.



29. REMOVE NO. 3 CHAIN VIBRATION DAMPER


G037296E01
  1. Remove the 2 bolts and chain vibration damper No.3.



30. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


G037297E01
  1. Remove the hexagon wrench from the tensioner assembly No.2.

  1. Remove the nut and chain tensioner assembly No.2.



31. REMOVE NO.2 CHAIN SUB-ASSEMBLY


G037298E01
  1. Remove the bolt, balanceshaft drive gear shaft and balanceshaft drive gear.

  1. Remove the crankshaft timing sprocket No.2 and chain.



32. REMOVE NO. 4 CHAIN VIBRATION DAMPER


G037299E01
  1. Remove the 2 bolts and vibration damper No.4.



33. REMOVE CRANKSHAFT PULLEY SET CRANKSHAFT KEY


G037300E02
  1. Remove the 2 pulley set keys from the crankshaft.



34. REMOVE OIL FILTER SUB-ASSEMBLY


G037302E02
  1. Using SST, remove the oil filter.

    SST
    09228-07501  



    G037462E01
  1. Using a 27 mm socket wrench, remove the oil filter union.



35. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY


G037304E02
  1. Remove the 2 bolts and nut from the oil filter bracket.

  1. Remove the 2 screw plugs and 2 gaskets from the oil filter bracket.



    G037305E03
  1. Remove the oil filter bracket gasket and O-ring.



    G037461E02
  1. Using a hexagon wrench, remove the oil filter bracket union.



36. REMOVE NO. 1 WITH HEAD TAPER SCREW PLUG


G038538E01
  1. Remove the taper screw plug from the cylinder block.



37. REMOVE ENGINE REAR OIL SEAL RETAINER


G037309E01
  1. Remove the 6 bolts.

  1. Using a screwdriver with its tip taped, pry out the oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.



38. REMOVE VALVE STEM CAP


G037289E01
  1. Remove the valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



39. REMOVE VALVE LASH ADJUSTER ASSEMBLY


G037290E01
  1. Remove the valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



40. REMOVE INTAKE VALVE


A097931E01
  1. Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.

    SST
    09202-70020   (09202-00010)



    G037449E01
  1. Remove the retainer, compression spring, and valve.

    HINT:
    Arrange the removed parts in the correct order.



41. REMOVE EXHAUST VALVE


A097932E01
  1. Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.

    SST
    09202-70020   (09202-00010)



    G037453E01
  1. Remove the retainer, compression spring, and valve.

    HINT:
    Arrange the removed parts in the correct order.



42. REMOVE VALVE STEM OIL SEAL


G037403E01
  1. Using needle-nose pliers, remove the oil seals.



43. REMOVE VALVE SPRING SEAT
  1. Remove the valve spring seats from the cylinder head.



44. REMOVE OIL CONTROL VALVE FILTER


G037445E01
  1. Using an 8 mm hexagon wrench, remove the screw plug.

  1. Remove the oil control valve filter and gasket.



45. REMOVE NO. 1 WITH HEAD STRAIGHT SCREW PLUG


G037405E01
  1. Using a 10 mm hexagon wrench, remove the 3 screw plugs and 3 gaskets.

    NOTICE:
    If water leaks from the w/ head straight screw plug No.1 or the plug corrodes, replace it.



46. REMOVE NO. 2 WITH HEAD STRAIGHT SCREW PLUG


G037406E01
  1. Using a 19 mm hexagon wrench, remove the screw plug and gasket.

    NOTICE:
    If water leaks from the w/ head straight screw plug No.2 or the plug corrodes, replace it.



47. REMOVE CRANKSHAFT BEARING


48. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD


G035191E05
  1. Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.



49. REMOVE CONNECTING ROD BEARING

HINT:
Arrange the removed parts in the correct order.



50. REMOVE CRANKSHAFT


G037353E01
  1. Uniformly loosen the 10 bearing cap bolts, in several steps, in the sequence shown in the illustration.

    HINT:
    1. Keep the lower bearings and crankshaft bearing caps together.
    2. Arrange the thrust washers in the correct order.

  1. Lift out the crankshaft.



    G037374E01
  1. Remove the upper bearings and upper thrust washers from the cylinder block.

    HINT:
    Arrange the main bearing caps, bearings and thrust washers in the correct order.



51. REMOVE CRANKSHAFT BEARING

HINT:
Arrange the removed parts in the correct order.



52. REMOVE PISTON RING SET


G037354E01
  1. Using a piston ring expander, remove the 2 compression rings.

  1. Using a piston ring expander, remove the oil ring rail.

  1. Remove the oil ring expander by hand.

    HINT:
    Arrange the piston rings in the correct order.



53. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


G037307E01
  1. Remove the water drain cock sub-assembly from the cylinder block.

  1. Remove the water drain cock plug from the water drain cock sub-assembly.



54. REMOVE WITH PIN PISTON SUB-ASSEMBLY


G035197E02
  1. Check the fitting condition between the piston and piston pin.

    1. Try to move the piston back and forth on the piston pin.
      If any movement is felt, replace the piston and pin as a set.



    G037386E01
  1. Disconnect the connecting rod from the piston.

    1. Using a screwdriver, pry off the snap rings from the piston.



    2. A001178E05
    3. Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).



    4. G036556E01
    5. Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.



55. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY


G037357E01
  1. Using a 5 mm hexagon wrench, remove the oil nozzles.



56. REMOVE NO.1 BALANCESHAFT


G037389E01
  1. Remove the bolt.



    G037390E01
  1. Remove the balanceshaft from the cylinder block.

    NOTICE:
    When removing the balanceshaft, make sure to support the balanceshaft with both hands and avoid scratching the balanceshaft bearing on the cylinder block side.



57. REMOVE NO. 1 BALANCESHAFT DRIVEN GEAR


G037391E03
  1. Mount the head portion of the balanceshaft in a vise.

    NOTICE:
    Be careful not to damage the balanceshaft.

  1. Remove the bolt.

  1. Remove the balanceshaft driven gear No.1 (*1), sliding key (*2), balanceshaft thrust washer No.1 (*3) and balanceshaft thrust spacer (*4).



58. REMOVE NO.2 BALANCESHAFT


G037392E01
  1. Remove the 2 bolts.



    G037393E01
  1. Remove the balanceshaft from the cylinder block.

    NOTICE:
    When removing the balanceshaft, make sure to support the balanceshaft with both hands and avoid scratching the balanceshaft bearing on the cylinder block side.



59. REMOVE NO. 2 BALANCESHAFT DRIVEN GEAR


G037394E04
  1. Mount the head portion of the balanceshaft in a vise.

    NOTICE:
    Be careful not to damage the balanceshaft.

  1. Remove the bolt.

  1. Remove the balanceshaft driven gear No.2 (*1) and balanceshaft thrust washer No.2 (*2).