Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

DTC    B15D3    Stereo Component Amplifier Disconnected

for Preparation Click here


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the radio and display receiver assembly and stereo component amplifier assembly, this DTC will be stored.

DTC No.
DTC Detection Condition
Trouble Area
B15D3*1
When either condition below is met:
  1. Stereo component amplifier assembly is/was not connected while the ignition switch is ON or ACC.
  2. Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.
  1. Stereo component amplifier assembly power source circuit
  2. AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly
  3. Stereo component amplifier assembly
  4. Radio and display receiver assembly
  5. Harness or connector

HINT:
  1. *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The radio and display receiver assembly is the master unit.


WIRING DIAGRAM


E233349E01


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC
  1. If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.
    Result 
    Result
    Proceed to
    DTC B15C3 is not output
    A
    DTC B15C3 is output
    B



B
GO TO DTC "B15C3" IN DIAGNOSTIC TROUBLE CODE CHART
A


2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check that optional components (including associated wiring) which generate radio waves are not installed.
    Result 
    Result
    Proceed to
    Optional components (including associated wiring) are installed.
    A
    Optional components (including associated wiring) are not installed.
    B

    HINT:
    1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
    2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 4
A


3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


4.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 5
OK

END 

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
  1. Disconnect the S23, S24 and S31 stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S24-6 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S31-1 (+B) - S24-6 (GND)
    Always
    11 to 14 V
    S31-5 (+B2) - S24-6 (GND)
    Always
    11 to 14 V
    S23-12 (ACC) - S24-6 (GND)
    Ignition switch ACC
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
  1. Disconnect the R16 radio and display receiver assembly connector.

  1. Disconnect the S23 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R16-5 (TX2+) - S23-8 (TX+)
    Always
    Below 1 Ω
    R16-15 (TX2-) - S23-7 (TX-)
    Always
    Below 1 Ω
    R16-5 (TX2+) - Body ground
    Always
    10 kΩ or higher
    R16-15 (TX2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END