Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
  4. Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


NO. 1 CAN JUNCTION CONNECTOR

C221688E10


Text in Illustration 
*a
Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b
to No. 2 CAN Junction Connector
*c
to ECM
*d
to Yaw Rate and Deceleration Sensor
*e
to DLC3
*f
to Center Airbag Sensor Assembly
*g
to Steering Angle Sensor
-
-

Terminal No. (Symbol)
Wiring Color
Connect to
J19-1 (CANH)
L-Y
No. 2 CAN Junction Connector
J19-12 (CANL)
W-L
No. 2 CAN Junction Connector
J19-2 (CANH)
B
ECM
J19-13 (CANL)
W
ECM
J19-3 (CANH)
Y
Yaw Rate and Deceleration Sensor
J19-14 (CANL)
L
Yaw Rate and Deceleration Sensor
J19-4 CANH)
Y-B
DLC3
J19-15 (CANL)
L-W
DLC3
J19-5 (CANH)
W
Center Airbag Assembly
J19-16 (CANL)
BE
Center Airbag Assembly
J19-6 (CANH)
Y-B
Steering Angle Sensor
J19-17 (CANL)
L-W
Steering Angle Sensor

NO. 2 CAN JUNCTION CONNECTOR

E223295E01


Text in Illustration 
*a
Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b
to Skid Control ECU
*c
to Combination Meter Assembly
*d
to No. 1 CAN Junction Connector

Terminal No. (Symbol)
Wiring Color
Connect to
J18-1 (CANH)
L-Y
Skid Control ECU
J18-3 (CANL)
W-L
Skid Control ECU
J18-2 (CANH)
L-Y
Combination Meter Assembly
J18-4 (CANL)
W-L
Combination Meter Assembly
J18-5 (CANH)
L-Y
No. 1 CAN Junction Connector
J18-7 (CANL)
W-L
No. 1 CAN Junction Connector

DLC3
E191939E12
  1. Turn the ignition switch off.

  2. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D4-6 (CANH) - D4-14 (CANL)
    Y-B - L-W
    Ignition switch off
    54 to 69 Ω
    D4-6 (CANH) - D4-4 (CG)
    Y-B - W-B
    Ignition switch off
    200 Ω or more
    D4-14 (CANL) - D4-4 (CG)
    L-W - W-B
    Ignition switch off
    200 Ω or more
    D4-6 (CANH) - D4-16 (BAT)
    Y-B - Y
    Ignition switch off
    6 kΩ or more
    D4-14 (CANL) - D4-16 (BAT)
    L-W - Y
    Ignition switch off
    6 kΩ or more


MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (for Hydraulic Booster Type)
E223286E01
  1. Turn the ignition switch off.

  2. Disconnect the S1 master cylinder solenoid (skid control ECU) connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    S1-11 (CANH) - S1-25 (CANL)
    L-Y - W-L
    Ignition switch off
    54 to 69 Ω
    S1-11 (CANH) - S1-32 (GND2)
    L-Y - W-B
    Ignition switch off
    200 Ω or higher
    S1-25 (CANL) - S1-32 (GND2)
    W-L - W-B
    Ignition switch off
    200 Ω or higher
    S1-11 (CANH) - S1-31 (+BS)
    L-Y - R
    Ignition switch off
    6 kΩ or higher
    S1-25 (CANL) - S1-31 (+BS)
    W-L - R
    Ignition switch off
    6 kΩ or higher


BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (for Vacuum Booster Type)
E223287E01
  1. Turn the ignition switch off.

  2. Disconnect the S1 brake actuator assembly (skid control ECU) connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly (Skid Control ECU))

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    S1-25 (CANH) - S1-14 (CANL)
    L-Y - W-L
    Ignition switch off
    54 to 69 Ω
    S1-25 (CANH) - S1-13 (GND2)
    L-Y - W-B
    Ignition switch off
    200 Ω or higher
    S1-14 (CANL) - S1-13 (GND2)
    W-L - W-B
    Ignition switch off
    200 Ω or higher
    S1-25 (CANH) - S1-24 (BM)
    L-Y - B
    Ignition switch off
    6 kΩ or higher
    S1-14 (CANL) - S1-24 (BM)
    W-L - B
    Ignition switch off
    6 kΩ or higher


ECM (for 1GR-FE)

E191996E04


Text in Illustration 
*a
Front view of wire harness connector
(to ECM)
-
-
  1. Turn the ignition switch off.

  2. Disconnect the E12, E13 and E14 ECM connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E14-32 (CANH) - E14-31 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E14-32 (CANH) - E12-14 (E01)
    B - W-B
    Ignition switch off
    200 Ω or higher
    E14-31 (CANL) - E12-14 (E01)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E14-32 (CANH) - E13-24 (BATT)
    B - L
    Ignition switch off
    6 kΩ or higher
    E14-31 (CANL) - E13-24 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


ECM (for 2TR-FE)

E223288E01


Text in Illustration 
*a
Front view of wire harness connector
(to ECM)
-
-
  1. Turn the ignition switch off.

  2. Disconnect the E4, E7 and E8 ECM connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E7-33 (CANH) - E7-34 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E7-33 (CANH) - E4-7 (E01)
    B - W-B
    Ignition switch off
    200 Ω or higher
    E7-34 (CANL) - E4-7 (E01)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E7-33 (CANH) - E8-3 (BATT)
    B - L
    Ignition switch off
    6 kΩ or higher
    E7-34 (CANL) - E8-3 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


YAW RATE AND DECELERATION SENSOR
E218497E03
  1. Turn the ignition switch off.

  2. Disconnect the Y2 yaw rate and deceleration sensor connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Deceleration Sensor)
    *b
    Front view of DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    Y2-3 (CANH) - Y2-2 (CANL)
    Y - L
    Ignition switch off
    54 to 69 Ω
    Y2-3 (CANH) - Y2-1 (GND)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    Y2-2 (CANL) - Y2-1 (GND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    Y2-3 (CANH) - D4-16 (BAT)
    Y - Y
    Ignition switch off
    6 kΩ or higher
    Y2-2 (CANL) - D4-16 (BAT)
    L - Y
    Ignition switch off
    6 kΩ or higher


STEERING ANGLE SENSOR
E231212E01
  1. Turn the ignition switch off.

  2. Disconnect the S32 steering angle sensor connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    S32-3 (CANH) - S32-2 (CANL)
    Y-B - L-W
    Ignition switch off
    54 to 69 Ω
    S32-3 (CANH) - S32-1 (ESS)
    Y-B - W-B
    Ignition switch off
    200 Ω or higher
    S32-2 (CANL) - S32-1 (ESS)
    L-W - W-B
    Ignition switch off
    200 Ω or higher
    S32-3 (CANH) - S32-5 (BAT)
    Y-B - R
    Ignition switch off
    6 kΩ or higher
    S32-2 (CANL) - S32-5 (BAT)
    L-W - R
    Ignition switch off
    6 kΩ or higher


COMBINATION METER ASSEMBLY
E221291E07
  1. Turn the ignition switch off.

  2. Disconnect the C9 combination meter assembly connectors.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    C9-8 (CANH) - C9-7 (CANL)
    L-Y - W-L
    Ignition switch off
    108 to 132 Ω
    C9-8 (CANH) - C9-2
    L-Y - W-B
    Ignition switch off
    200 Ω or higher
    C9-7 (CANL) - C9-2
    W-L - W-B
    Ignition switch off
    200 Ω or higher
    C9-8 (CANH) - C9-1
    L-Y - R
    Ignition switch off
    6 kΩ or higher
    C9-7 (CANL) - C9-1
    W-L - R
    Ignition switch off
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY
E176022E08
  1. Turn the ignition switch off.

  2. Disconnect the A21 center airbag sensor assembly.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A21-13 (CANH) - A21-22 (CANL)
    W - BE
    Ignition switch off
    54 to 69 Ω
    A21-13 (CANH) - D4-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A21-22 (CANL) - D4-4 (CG)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    A21-13 (CANH) - D4-16 (BAT)
    W - Y
    Ignition switch off
    6 kΩ or higher
    A21-22 (CANL) - D4-16 (BAT)
    BE - Y
    Ignition switch off
    6 kΩ or higher