Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) > TERMINALS OF ECU

for Preparation Click here



TERMINALS OF ECU

C237105E01


Text in Illustration 
*a
Component without harness connected
(Skid Control ECU (Master Cylinder Solenoid))
-
-

Terminal No. (Symbol)
Terminal Description
S1-1 (GND1)
Ground
S1-2 (+BM1)
Power supply for motor
S1-3 (FR+)
Front wheel speed sensor RH power supply output
S1-4 (FL-)
Front wheel speed LH signal input
S1-5 (RR+)
Rear wheel speed sensor RH power supply output
S1-6 (RL-)
Rear wheel speed LH signal input
S1-7 (STP)
Stop light switch input
S1-9 (CSW)
VSC OFF switch input
S1-11 (CANH)
CAN communication line H
S1-12 (SP1)
Speed signal output for speedometer
S1-13 (ATRC)
A-TRAC switch input
S1-14 (P)*1
Shift position indicator P signal input
S1-16 (STPO)
Stop light operated relay output
S1-17 (FR-)
Front wheel speed sensor RH input
S1-18 (FL+)
Front wheel speed sensor LH power supply output
S1-19 (RR-)
Rear wheel speed sensor RH input
S1-20 (RL+)
Rear wheel speed sensor LH power supply output
S1-24 (TS)
Sensor test terminal (Sensor check switch) input
S1-25 (CANL)
CAN communication line L
S1-27 (EXI)
L4 detection switch input
S1-28 (PKB)
Parking brake switch input
S1-29 (EXI4)
4WD detection switch input
S1-31 (+BS)
Power supply for solenoid
S1-32 (GND2)
Ground
S1-40 (EXI3)
Differential lock indicator switch input
S1-41 (LBL)
Brake fluid level warning switch input
S1-44 (HDCS)*2
Downhill assist control switch input
S1-45 (STP2)
Stop light switch input
S1-46 (IG1)
IG1 power supply
S2-1 (IG2)
IG2 power supply
S2-2 (+BM2)
Power supply for motor
S2-4 (GND3)
Ground
  1. *1: for Automatic Transmission
  2. *2: w/ Downhill Assist Control

TERMINAL INSPECTION
Disconnect the connector and measure the voltage or resistance on the wire harness side.

HINT:
Voltage cannot be measured with the connector connected to the skid control ECU (master cylinder solenoid) as the connector is water resistant.


C237106E01


Text in Illustration 
*a
Front view of wire harness connector
(Skid Control ECU (Master Cylinder Solenoid))
-
-

Standard 
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
S1-1 (GND1) - Body ground
W-B
Ground
Always
Below 1 Ω
S1-2 (+BM1) - Body ground
B
Power supply for motor from battery
Always
11 to 14 V
S1-7 (STP) - Body ground
L
Stop light switch input
Stop light switch off (Brake pedal released)
Below 1.5 V
Stop light switch on (Brake pedal depressed)
8 to 14 V
S1-9 (CSW) - Body ground
GR-B
VSC OFF switch input
VSC OFF switch off
10 kΩ or higher
VSC OFF switch on and hold
Below 1 Ω
S1-13 (ATRC) - Body ground
R-B
A-TRAC switch input
A-TRAC switch off
10 kΩ or higher
A-TRAC switch on and hold
Below 1 Ω
S1-14 (P) - Body ground*1
BR-W
Shift position indicator P signal input
Ignition switch ON
Shift lever in P
11 to 14 V
Ignition switch ON
Shift lever in not P
Below 1 V
S1-16 (STPO) - Body ground
G-B
Stop light operated relay output
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
S1-27 (EXI) - Body ground
Y-B
L4 detection switch input
Ignition switch ON
Transfer position in L4
Below 1.5 V
Ignition switch ON
Transfer condition not in L4
11 to 14 V
S1-28 (PKB) - Body ground
G-Y
Parking brake switch input
Parking brake switch off
10 kΩ or higher
Parking brake switch on
Below 1 Ω
S1-29 (EXI4) - Body ground
LG-B
4WD detection switch input
Ignition switch ON
Transfer condition in H4 or L4
Below 1.5 V
Ignition switch ON
Transfer condition in H2
11 to 14 V
S1-31 (+BS) - Body ground
R
Power supply for solenoid from battery
Always
11 to 14 V
S1-32 (GND2) - Body ground
W-B
Ground
Always
Below 1 Ω
S1-40 (EXI3) - Body ground
L-Y
Differential lock indicator switch input
Ignition switch ON
Rear differential lock switch on
Below 1.5 V
Ignition switch ON
Rear differential lock switch off
11 to 14 V
S1-41 (LBL) - Body ground
V-W
Brake fluid level warning switch input
Brake fluid level min. -5 mm
Below 1 Ω
Brake fluid level max.
1.9 to 2.1 kΩ
S1-44 (HDCS) - Body ground*2
P-B
Downhill assist control switch input
Downhill assist control switch off
10 kΩ or higher
Downhill assist control switch on
Below 1 Ω
S1-45 (STP2) - Body ground
L
Stop light switch input
Stop light switch off (Brake pedal released)
Below 1.5 V
Stop light switch on (Brake pedal depressed)
8 to 14 V
S1-46 (IG1) - Body ground
LG
IG1 power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
S2-1 (IG2) - Body ground
BE
IG2 power supply
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
S2-2 (+BM2) - Body ground
B
Power supply for motor from battery
Always
11 to 14 V
S2-4 (GND3) - Body ground
W-B
Ground
Always
Below 1 Ω
  1. *1: for Automatic Transmission
  2. *2: w/ Downhill Assist Control