Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

DTC    C1253    Pump Motor Relay

for Preparation Click here


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid).

DTC No.
DTC Detecting Condition
Trouble Areas
C1253
Open in motor system circuit (motor input circuit)
  1. Hydraulic brake booster pump motor
  2. Hydraulic brake booster pump motor circuit

WIRING DIAGRAM


C124775E04


INSPECTION PROCEDURE

HINT:
Start the inspection from step 1 when using Techstream and start from step 3 when not using Techstream.

1.PERFORM ACTIVE TEST USING TECHSTREAM (MOTOR RELAY)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn Techstream ON.

  1. Select the Active Test mode on the Techstream.

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    Turns motor relay
    ON / OFF
    Operation of motor can be heard

  1. Check for operation sound of the motor when it is operated with Techstream.

    OK:
    The operation sound of the motor can be heard.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to OFF.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to the ON position.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor is turned on.

  1. Wait until the pump stops.

  1. Repeat (f) and (g) three times.

  1. Check if the same DTCs are recorded.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE HYDRAULIC BRAKE BOOSTER 

3.INSPECT FUSE (ABS NO. 1)


    F051653E11
  1. Remove the ABS NO. 1 fuse from the engine room R/B and J/B.

  1. Measure the resistance of the ABS NO. 1 fuse.

    Standard:
    Below 1 Ω

  1. Reinstall the ABS NO. 1.



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


4.INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (+BM, +BM2 TERMINAL)


    C124799E02
  1. Disconnect the skid control ECU (master cylinder solenoid) connectors.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Specified Condition
    S1-2 (+BM1) - Body ground
    10 to 14 V
    S2-2 (+BM2) - Body ground
    10 to 14 V

  1. Reconnect the skid control ECU (master cylinder solenoid) connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM1 AND +BM2 CIRCUIT)
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BODY GROUND)


    C124799E01
  1. Disconnect the skid control ECU (master cylinder solenoid) connectors.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    S1-1 (GND1) - Body ground
    Below 1 Ω
    S1-32 (GND2) - Body ground
    Below 1 Ω
    S2-4 (GND3) - Body ground
    Below 1 Ω

  1. Reconnect the skid control ECU (master cylinder solenoid) connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to OFF.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to the ON position.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor is turned on.

  1. Wait until the pump stops.

  1. Repeat (f) and (g) three times.

  1. Check if the same DTCs are recorded.

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE HYDRAULIC BRAKE BOOSTER