WHEEL OPENING MOULDING > REMOVAL |
| 1. REMOVE FRONT SPOILER COVER (for X-Runner) |
![]() |
Remove the 6 retainers.
![]() |
Using a clip remover, remove the 3 clips.
Remove the retainer and the front spoiler cover.
| 2. REMOVE FRONT BUMPER EXTENSION |
![]() |
Remove the 2 screws.
Using the screwdriver, remove the pin hold clip.
![]() |
for Type A:
Remove the screw.
Remove the 7 retainers and front bumper extension.
![]() |
for Type B:
Remove the screw.
Remove the 5 retainers and front bumper extension.
| 3. REMOVE FRONT FENDER MUDGUARD (w/ Front Fender Mudguard) |
![]() |
Using a clip remover, remove the 3 clips.
Remove the 3 screws and front fender mudguard.
| 4. REMOVE ROCKER PANEL MOULDING (for X-Runner) |
![]() |
Remove the 4 screws.
![]() |
Apply protective tape to the outer circumference of the rocker panel moulding, as shown in the illustration.
Using a moulding remover, disengage the 9 clips and remove the rocker panel moulding.
![]() |
Turn the clips 90° clockwise and remove them.
| 5. REMOVE FRONT FENDER WHEEL OPENING MOULDING |
![]() |
w/o Front fender mudguard:
Remove the screw and the 3 clips.
![]() |
for Type A:
Remove the 4 screws.
![]() |
Apply protective tape to the outer circumference of the front fender wheel opening moulding, as shown in the illustration.
Using a moulding remover, disengage the 9 clips and remove the front fender wheel opening moulding.
| *1 | Moulding Remover |
| *2 | Protective Tape |
![]() |
Turn the clips 90° clockwise and remove them.
![]() |
for Type B:
Remove the 5 screws and front fender wheel opening moulding.
| 6. REMOVE REAR QUARTER PANEL MUDGUARD (w/ Rear Fender Mudguard) |
![]() |
for Type A:
Using a clip remover, remove the 3 clips.
Remove the 3 screws and rear quarter panel mudguard.
![]() |
for Type B:
Remove the 3 screws and rear quarter panel mudguard.
| 7. REMOVE BACK DOOR OUTSIDE MOULDING SUB-ASSEMBLY (for X-Runner) |
![]() |
Remove the 3 screws.
![]() |
Apply protective tape to the outer circumference of the back door outside moulding, as shown in the illustration.
Using a moulding remover, disengage the 3 clips and remove the back door outside moulding.
![]() |
Turn the clips 90° clockwise and remove them.
| 8. REMOVE BODY ROCKER PANEL MOULDING ASSEMBLY (for X-Runner) |
![]() |
Remove the 3 screws.
![]() |
Apply protective tape to the outer circumference of the body rocker panel moulding, as shown in the illustration.
Using a moulding remover, disengage the 3 clips and remove the body rocker panel moulding.
![]() |
Turn the 90° clockwise and remove them.
| 9. REMOVE QUARTER PANEL WHEEL OPENING MOULDING |
![]() |
for Type A:
Remove the 5 screws.
![]() |
Apply protective tape to the outer circumference of the quarter panel wheel opening moulding, as shown in the illustration.
Using a moulding remover, disengage the 10 clips and remove the quarter panel wheel opening moulding.
| *1 | Moulding Remover |
| *2 | Protective Tape |
![]() |
Turn the clips 90° clockwise and remove them.
![]() |
for Type B:
Remove the 5 screws and quarter panel wheel opening moulding.