Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Vacuum Brake Booster)

VEHICLE STABILITY CONTROL SYSTEM (for Vacuum Brake Booster) > TERMINALS OF ECU

for Preparation Click here



SKID CONTROL ECU

C237107E01


Text in Illustration 
*a
Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
-
-

Terminal No. (Symbol)
Terminal Description
S1-1 (GND1)
Ground
S1-2 (STP)
Stop light switch input
S1-4 (RL-)
Rear wheel speed sensor LH signal input
S1-5 (RL+)
Rear wheel speed sensor LH power supply output
S1-6 (FR-)
Front wheel speed sensor RH signal input
S1-7 (FR+)
Front wheel speed sensor RH power supply output
S1-9 (EXI4)
L4 detection switch input*1
S1-11 (SP1)
Speed signal output for speedometer
S1-12 (+BS)
Power supply for solenoid relay
S1-13 (GND2)
Ground
S1-14 (CANL)
CAN communication line L
S1-16 (RR-)
Rear wheel speed sensor RH signal input
S1-17 (RR+)
Rear wheel speed sensor RH power supply output
S1-18 (FL-)
Front wheel speed sensor LH signal input
S1-19 (FL+)
Front wheel speed sensor LH power supply output
S1-20 (EXI)
4WD detection switch input*1
S1-22 (STP2)
Stop light switch input*5
S1-24 (BM)
Power supply for motor
S1-25 (CANH)
CAN communication line H
S1-26 (NEO)
4WD identification signal input*1
S1-28 (EXI3)
Differential lock indicator switch input *3
IG power supply *4
S1-29 (PKB)
Parking brake switch input
S1-30 (CSW)
VSC OFF switch input
S1-31 (STPO)
Stop light operated relay output*5
S1-32 (P)
Shift position indicator P signal input*2
S1-33 (TS)
Sensor test terminal (Signal check switch)
S1-34 (IG1)
IG1 power supply
  1. *1: for 4WD
  2. *2: for Automatic Transmission
  3. *3: w/ Rear Differential Lock
  4. *4: w/o Rear Differential Lock
  5. *5: w/ Trailer Towing

CHECK SKID CONTROL ECU
  1. Disconnect the S1 skid control ECU connector.



  2. Measure the voltage or resistance according to the value(s) in the table below.

    HINT:
    Voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.


    C237108E01


    Text in Illustration 
    *a
    Front view of wire harness connector
    (Skid Control ECU (Brake Actuator Assembly))
    -
    -

    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S1-1 (GND1) - Body ground
    W-B
    Ground
    Always
    Below 1 Ω
    S1-2 (STP) - Body ground
    L
    Stop light switch input
    Stop light switch off (Brake pedal released)
    Below 1.5 V
    Stop light switch on (Brake pedal depressed)
    11 to 14 V
    S1-9 (EXI4) - Body ground*1
    Y-B
    L4 detection switch input
    Ignition switch ON
    Transfer position in L4
    Below 1.5 V
    Ignition switch ON
    Transfer condition not in L4
    11 to 14 V
    S1-12 (+BS) - Body ground
    R
    Power supply for solenoid relay
    Always
    11 to 14 V
    S1-13 (GND2) - Body ground
    W-B
    Ground
    Always
    Below 1 Ω
    S1-20 (EXI) - Body ground*1
    LG-B
    4WD detection switch input
    Ignition switch ON
    Transfer condition in H4 or L4
    Below 1.5 V
    Ignition switch ON
    Transfer condition in H2
    11 to 14 V
    S1-22 (STP2) - Body ground*5
    L
    Stop light switch input
    Stop light switch off (Brake pedal released)
    Below 1.5 V
    Stop light switch on (Brake pedal depressed)
    8 to 14 V
    S1-24 (BM) - Body ground
    B
    Power supply for motor
    Always
    11 to 14 V
    S1-26 (NEO) - Body ground*1
    W-B
    4WD identification signal input
    Always
    Below 1 Ω
    S1-28 (EXI3) - Body ground*3
    L-Y
    Differential lock indicator switch input
    Ignition switch ON
    Differential lock switch on
    Below 1.5 V
    Ignition switch ON
    Differential lock switch off
    11 to 14 V
    S1-28 (EXI3) - Body ground*4
    L-Y
    IG power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    S1-29 (PKB) - Body ground
    G-Y
    Parking brake switch input
    Parking brake switch off
    10 kΩ or higher
    Parking brake switch on
    Below 1 Ω
    S1-30 (CSW) - Body ground
    GR-B
    VSC OFF switch input
    VSC OFF switch off
    10 kΩ or higher
    VSC OFF switch on and held
    Below 1 Ω
    S1-31 (STPO) - Body ground*5
    G-B
    Stop light operated relay output
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    S1-32 (P) - Body ground*2
    BR-W
    Shift position indicator P signal input
    Ignition switch ON
    Shift lever in P
    11 to 14 V
    Ignition switch ON
    Shift lever in not P
    Below 1 V
    S1-34 (IG1) - Body ground
    LG
    IG power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    1. *1: for 4WD
    2. *2: for Automatic Transmission
    3. *3: w/ Rear Differential Lock
    4. *4: w/o Rear Differential Lock
    5. *5: w/ Trailer Towing