Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2741    Transmission Fluid Temperature Sensor "B" Performance

for Preparation Click here


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input to the ECM. The sensor resistance changes with the transmission fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1, and the ECM calculates the fluid temperature based on the voltage signal.

HINT:
The ATF temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No.
DTC Detection Conditions
Trouble Areas
P2741
When one of the condition below is met:
  1. ATF level
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM
Condition (A):
(a), (b), (c), (d) and (e) are detected: (2-trip detection logic)
(a) After the engine is stopped, 5 hours or more elapse before the engine is started
(b) After normal driving for 68 seconds and 5.0 km (3.0 miles) or more
(c) Engine coolant and intake air temperature is 15°C (59°F) or more at 12 seconds after engine start
(d) ATF temperature is less than 20°C (68°F)
(e) Engine has been running for at least 10 minutes
Condition (B):
All of (a), (b) and (c) are detected (2-trip detection logic)
  1. (a) Intake air and engine coolant temperatures are more than -10°C (14°F) at engine start.
  2. (b) After normal driving for over 4 minutes and 10 seconds and 9 km (5.6 miles) or more, ATF temperature is less than 20°C (68°F).
  3. (c) 18 min. and 20 seconds or more have elapsed after engine start.
Condition (C):
Both (a) and (b) are detected (2-trip detection logic)
  1. (a) Engine coolant temperature is less than 35°C (95°F) at engine start.
  2. (b) ATF temperature is 110°C (230°F) or more when engine coolant temperature reaches 60°C (140°F).

MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects opens or shorts in the ATF temperature circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, and turns on the MIL.
When the ATF temperature is 110°C (230°F) or more and the engine coolant temperature reaches 60°C (140°F) after a cold start, the ECM also interprets this as a fault, turns on the MIL, and stores the DTC.

MONITOR STRATEGY


Related DTCs
P2741: ATF temperature sensor/Rationality check
Required sensors/Components
No. 1 ATF temperature sensor
Frequency of operation
Continuous
Duration
3 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


ALL 
The monitor will run whenever the following DTCs are not present
Not circuit malfunctionP2742, P2743 (Transmission temperature sensor "B" circuit)
P0128 (ECT (Engine coolant temperature) sensor circuit)
P0112, P0113 (IAT (Intake Air Temperature) sensor circuit)

Condition (A) 
Time after engine start
10 minutes or more
Driving distance after engine start
5.0 km (3.0 miles) or more
IAT (12 seconds after engine start)
15°C (59°F) or more
ECT (12 seconds after engine start)
15°C (59°F) or more
Soak time
5 hours or more

Condition (B) 
Time after engine start
18 minutes and 20 seconds or more
Driving distance after engine start
9 km (5.6 miles) or more
IAT (12 seconds after engine start)
-10°C (14°F) or more
ECT (12 seconds after engine start)
-10°C (14°F) or more

Condition (C) 
Time after ECT reaches 60°C (140°F)
10 seconds or more
ATF temperature (12 seconds after engine start)
110°C (230°F) or more
ECT (12 seconds after engine start)
Less than 35°C (95°F)

TYPICAL MALFUNCTION THRESHOLDS


Condition (A) and (B) 
ATF temperature
Less than 20°C (68°F)

Condition (C) 
ATF temperature
110°C (230°F) or more

COMPONENT OPERATING RANGE


ATF temperature
20 to 110°C (68 to 230°F)

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


DATA LIST

HINT:
According to the Data List displayed by Techstream, you can read the values of switches, sensors, actuators and so on without removing parts. Reading the Data List as the first step of troubleshooting is one method to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or short circuited

    HINT:
    When DTC P2742 is output and Techstream reading is 150°C (302°F) or more, there is a short circuit.
    When DTC P2743 is output and Techstream reading is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the tester in order to check if a malfunction exists.


    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit

HINT:
It is not necessary to inspect the circuit when P2741 is set.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2741)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using Techstream.
    Result 
    Result
    Proceed to
    Only P2741 is output
    A
    P2741 and other DTCs are output
    B

    HINT:
    If any codes besides P2741 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK TRANSMISSION FLUID LEVEL
  1. Check the transmission fluid level (Click here).

    OK:
    Automatic transmission fluid level is correct.



NG
ADD FLUID
OK

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR) (Click here)