Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM


E232754E04


INSPECTION PROCEDURE

NOTICE:
After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
  1. Disconnect the R15 radio and display receiver assembly connector.

  1. Disconnect the T21 telephone microphone assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R15-4 (MACC) - T21-1 (MACC)
    Always
    Below 1 Ω
    R15-5 (MIN+) - T21-2 (MCO+)
    Always
    Below 1 Ω
    R15-19 (MIN-) - T21-4 (MCO-)
    Always
    Below 1 Ω
    R15-6 (SNS2) - T21-3 (SNS2)
    Always
    Below 1 Ω
    R15-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    R15-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    R15-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    R15-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    R15-6 (SNS2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the radio and display receiver assembly connector.

  1. Reconnect the telephone microphone assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E176671E72
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R15-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R15-19 (MIN-) - Body ground
    Always
    Below 1 Ω
    R15-18 (SGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT TELEPHONE MICROPHONE ASSEMBLY


    E233345E01
  1. Remove the telephone microphone assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (SNS2) - 4 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Telephone Microphone Assembly)



NG
REPLACE TELEPHONE MICROPHONE ASSEMBLY (Click here)
OK


4.INSPECT TELEPHONE MICROPHONE ASSEMBLY


    E233849E02
  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the telephone microphone assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.
    Result 
    Result
    Proceed to
    A waveform synchronized with the voice input to the telephone microphone assembly is output
    A
    A waveform synchronized with the voice input to the telephone microphone assembly is not output
    B
    Text in Illustration 
    *a
    Component with harness connected
    (Telephone Microphone Assembly)



B
REPLACE TELEPHONE MICROPHONE ASSEMBLY (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)